[clinton/Smoothieware.git] / ConfigSamples / Smoothieboard / config

# NOTE Lines must not exceed 132 characters
# Robot module configurations : general handling of movement G-codes and slicing into moves
default_feed_rate                            4000             # Default rate ( mm/minute ) for G1/G2/G3 moves
default_seek_rate                            4000             # Default rate ( mm/minute ) for G0 moves
mm_per_arc_segment                           0.5              # Arcs are cut into segments ( lines ), this is the length for
                                                              # these segments.  Smaller values mean more resolution,
                                                              # higher values mean faster computation
mm_per_line_segment                          5                # Lines can be cut into segments ( not usefull with cartesian
                                                              # coordinates robots ).

# Arm solution configuration : Cartesian robot. Translates mm positions into stepper positions
alpha_steps_per_mm                           80               # Steps per mm for alpha stepper
beta_steps_per_mm                            80               # Steps per mm for beta stepper
gamma_steps_per_mm                           1600             # Steps per mm for gamma stepper

# Planner module configuration : Look-ahead and acceleration configuration
planner_queue_size                           32               # DO NOT CHANGE THIS UNLESS YOU KNOW EXACTLY WHAT YOU ARE DOING
acceleration                                 3000             # Acceleration in mm/second/second.
acceleration_ticks_per_second                1000             # Number of times per second the speed is updated
junction_deviation                           0.05             # Similar to the old "max_jerk", in millimeters,
                                                              # see https://github.com/grbl/grbl/blob/master/planner.c#L409
                                                              # and https://github.com/grbl/grbl/wiki/Configuring-Grbl-v0.8
                                                              # Lower values mean being more careful, higher values means being
                                                              # faster and have more jerk
#minimum_planner_speed                       0.0              # sets the minimum planner speed in mm/sec

# Stepper module configuration
microseconds_per_step_pulse                  1                # Duration of step pulses to stepper drivers, in microseconds
minimum_steps_per_minute                     1200             # Never step slower than this
base_stepping_frequency                      100000           # Base frequency for stepping, higher gives smoother movement

# Cartesian axis speed limits
x_axis_max_speed                             30000            # mm/min
y_axis_max_speed                             30000            # mm/min
z_axis_max_speed                             300              # mm/min

# Stepper module pins ( ports, and pin numbers, appending "!" to the number will invert a pin )
alpha_step_pin                               2.0              # Pin for alpha stepper step signal
alpha_dir_pin                                0.5              # Pin for alpha stepper direction
alpha_en_pin                                 0.4              # Pin for alpha enable pin
alpha_current                                1.5              # X stepper motor current
alpha_max_rate                               30000.0          # mm/min

beta_step_pin                                2.1              # Pin for beta stepper step signal
beta_dir_pin                                 0.11             # Pin for beta stepper direction
beta_en_pin                                  0.10             # Pin for beta enable
beta_current                                 1.5              # Y stepper motor current
beta_max_rate                                30000.0          # mm/min

gamma_step_pin                               2.2              # Pin for gamma stepper step signal
gamma_dir_pin                                0.20             # Pin for gamma stepper direction
gamma_en_pin                                 0.19             # Pin for gamma enable
gamma_current                                1.5              # Z stepper motor current
gamma_max_rate                               300.0            # mm/min

# Serial communications configuration ( baud rate default to 9600 if undefined )
uart0.baud_rate                              115200           # Baud rate for the default hardware serial port
second_usb_serial_enable                     false            # This enables a second usb serial port (to have both pronterface
                                                              # and a terminal connected)
#leds_disable                                true             # disable using leds after config loaded


# Extruder module configuration
extruder.hotend.enable                          true             # Whether to activate the extruder module at all. All configuration is ignored if false
extruder.hotend.steps_per_mm                    140              # Steps per mm for extruder stepper
extruder.hotend.default_feed_rate               600              # Default rate ( mm/minute ) for moves where only the extruder moves
extruder.hotend.acceleration                    500              # Acceleration for the stepper motor, as of 0.6, arbitrary ratio
extruder.hotend.max_speed                       50               # mm/s

extruder.hotend.step_pin                        2.3              # Pin for extruder step signal
extruder.hotend.dir_pin                         0.22             # Pin for extruder dir signal
extruder.hotend.en_pin                          0.21             # Pin for extruder enable signal

# for now the first extruder's offsets should be left at 0 or homing will get confused
#extruder.hotend.x_offset                        0                # x offset from origin in mm
#extruder.hotend.y_offset                        0                # y offset from origin in mm
#extruder.hotend.z_offset                        0                # z offset from origin in mm

delta_current                                1.5              # First extruder stepper motor current

# Second extruder module configuration
#extruder.hotend2.enable                          true             # Whether to activate the extruder module at all. All configuration is ignored if false
#extruder.hotend2.steps_per_mm                    140              # Steps per mm for extruder stepper
#extruder.hotend2.default_feed_rate               600              # Default rate ( mm/minute ) for moves where only the extruder moves
#extruder.hotend2.acceleration                    500              # Acceleration for the stepper motor, as of 0.6, arbitrary ratio
#extruder.hotend2.max_speed                       50               # mm/s

#extruder.hotend2.step_pin                        2.8              # Pin for extruder step signal
#extruder.hotend2.dir_pin                         2.13             # Pin for extruder dir signal
#extruder.hotend2.en_pin                          4.29             # Pin for extruder enable signal

#extruder.hotend2.x_offset                        0                # x offset from origin in mm
#extruder.hotend2.y_offset                        25.0             # y offset from origin in mm
#extruder.hotend2.z_offset                        0                # z offset from origin in mm
#epsilon_current                              1.5              # Second extruder stepper motor current

# Laser module configuration
laser_module_enable                          false            # Whether to activate the laser module at all. All configuration is
                                                              # ignored if false.
#laser_module_pin                             2.5             # this pin will be PWMed to control the laser. Only P2.0 - P2.5
                                                              # can be used since laser requires hardware PWM
#laser_module_max_power                       0.8             # this is the maximum duty cycle that will be applied to the laser
#laser_module_tickle_power                    0.0             # this duty cycle will be used for travel moves to keep the laser
                                                              # active without actually burning
#laser_module_pwm_period                      20              # this sets the pwm frequency as the period in microseconds

# Hotend temperature control configuration
temperature_control.hotend.enable            true             # Whether to activate this ( "hotend" ) module at all.
                                                              # All configuration is ignored if false.
temperature_control.hotend.link_to_tool      true             # This tells smoothie to enable and disable control of this hotend at the same time as the extruder of the same name
temperature_control.hotend.thermistor_pin    0.23             # Pin for the thermistor to read
temperature_control.hotend.heater_pin        2.7              # Pin that controls the heater
temperature_control.hotend.thermistor        EPCOS100K        # see src/modules/tools/temperaturecontrol/TemperatureControl.cpp:64
                                                              # for a list of valid thermistor names
temperature_control.hotend.set_m_code        104              #
temperature_control.hotend.set_and_wait_m_code 109            #
temperature_control.hotend.designator        T                #

#temperature_control.hotend.p_factor         13.7             # permanently set the PID values after an auto pid
#temperature_control.hotend.i_factor         0.097            #
#temperature_control.hotend.d_factor         24               #

#temperature_control.hotend.max_pwm          64               # max pwm, 64 is a good value if driving a 12v resistor with 24v.

# Hotend2 temperature control configuration
#temperature_control.hotend2.enable            true             # Whether to activate this ( "hotend" ) module at all.
                                                              # All configuration is ignored if false.
#temperature_control.hotend2.link_to_tool      true            # This tells smoothie to enable and disable control of this hotend at the same time as the extruder of the same name
#temperature_control.hotend2.thermistor_pin    0.25             # Pin for the thermistor to read
#temperature_control.hotend2.heater_pin        1.23              # Pin that controls the heater
#temperature_control.hotend2.thermistor        EPCOS100K        # see src/modules/tools/temperaturecontrol/TemperatureControl.cpp:64
                                                              # for a list of valid thermistor names
#temperature_control.hotend2.set_m_code        884              #
#temperature_control.hotend2.set_and_wait_m_code 889            #
#temperature_control.hotend2.designator        T1               #

#temperature_control.hotend2.p_factor          13.7           # permanently set the PID values after an auto pid
#temperature_control.hotend2.i_factor          0.097          #
#temperature_control.hotend2.d_factor          24             #

#temperature_control.hotend.max_pwm          64               # max pwm, 64 is a good value if driving a 12v resistor with 24v.

temperature_control.bed.enable               true             #
temperature_control.bed.thermistor_pin       0.24             #
temperature_control.bed.heater_pin           2.5              #
temperature_control.bed.thermistor           Honeywell100K    # see src/modules/tools/temperaturecontrol/TemperatureControl.cpp:64
                                                              # for a list of valid thermistor names
temperature_control.bed.set_m_code           140              #
temperature_control.bed.set_and_wait_m_code  190              #
temperature_control.bed.designator           B                #

#temperature_control.bed.bang_bang            false           # set to true to use bang bang control rather than PID
#temperature_control.bed.hysteresis           2.0             # set to the temperature in degrees C to use as hysteresis
                                                              # when using bang bang

# Switch module for fan control
switch.fan.enable                            true             #
switch.fan.input_on_command                  M106             #
switch.fan.input_off_command                 M107             #
switch.fan.output_pin                        2.6              #
switch.fan.output_type                       pwm              # pwm output settable with S parameter in the input_on_comand
#switch.fan.max_pwm                           255              # set max pwm for the pin default is 255

#switch.misc.enable                           true             #
#switch.misc.input_on_command                 M42              #
#switch.misc.input_off_command                M43              #
#switch.misc.output_pin                       2.4              #
#switch.misc.output_type                      digital          # just an on or off pin

# Switch module for spindle control
#switch.spindle.enable                        false            #

# Endstops
endstops_enable                              true             # the endstop module is enabled by default and can be disabled here
#corexy_homing                               false            # set to true if homing on a hbit or corexy
alpha_min_endstop                            1.24^            # add a ! to invert if endstop is NO connected to ground
alpha_max_endstop                            1.25^            #
alpha_homing_direction                       home_to_min      # or set to home_to_max and set alpha_max
alpha_min                                    0                # this gets loaded after homing when home_to_min is set
alpha_max                                    200              # this gets loaded after homing when home_to_max is set
beta_min_endstop                             1.26^            #
beta_max_endstop                             1.27^            #
beta_homing_direction                        home_to_min      #
beta_min                                     0                #
beta_max                                     200              #
gamma_min_endstop                            1.28^            #
gamma_max_endstop                            1.29^            #
gamma_homing_direction                       home_to_min      #
gamma_min                                    0                #
gamma_max                                    200              #

alpha_fast_homing_rate_mm_s                  50               # feedrates in mm/second
beta_fast_homing_rate_mm_s                   50               # "
gamma_fast_homing_rate_mm_s                  4                # "
alpha_slow_homing_rate_mm_s                  25               # "
beta_slow_homing_rate_mm_s                   25               # "
gamma_slow_homing_rate_mm_s                  2                # "

alpha_homing_retract_mm                      5                # distance in mm
beta_homing_retract_mm                       5                # "
gamma_homing_retract_mm                      1                # "

#endstop_debounce_count                       100              # uncomment if you get noise on your endstops

# Pause button
pause_button_enable                          true             #

# Panel
panel.enable                                 false             # set to true to enable the panel code
panel.lcd                                    smoothiepanel     # set type of panel
panel.encoder_a_pin                          3.25!^            # encoder pin
panel.encoder_b_pin                          3.26!^            # encoder pin

# Example for reprap discount GLCD
# on glcd EXP1 is to left and EXP2 is to right, pin 1 is bottom left, pin 2 is top left etc.
# +5v is EXP1 pin 10, Gnd is EXP1 pin 9
#panel.lcd                                   reprap_discount_glcd     #
#panel.spi_channel                           0                 # spi channel to use  ; GLCD EXP1 Pins 3,5 (MOSI, SCLK)
#panel.spi_cs_pin                            0.16              # spi chip select     ; GLCD EXP1 Pin 4
#panel.encoder_a_pin                         3.25!^            # encoder pin         ; GLCD EXP2 Pin 3
#panel.encoder_b_pin                         3.26!^            # encoder pin         ; GLCD EXP2 Pin 5
#panel.click_button_pin                      1.30!^            # click button        ; GLCD EXP1 Pin 2
#panel.buzz_pin                              1.31              # pin for buzzer      ; GLCD EXP1 Pin 1
#panel.button_pause_pin                      2.11^             # kill/pause          ; GLCD EXP2 Pin 8 either
#panel.back_button_pin                       2.11!^            # back button         ; GLCD EXP2 Pin 8 or

# pins used with other panels
#panel.up_button_pin                         0.1!              # up button if used
#panel.down_button_pin                       0.0!              # down button if used
#panel.click_button_pin                      0.18!             # click button if used

panel.menu_offset                            0                 # some panels will need 1 here

panel.alpha_jog_feedrate                     6000              # x jogging feedrate in mm/min
panel.beta_jog_feedrate                      6000              # y jogging feedrate in mm/min
panel.gamma_jog_feedrate                     200               # z jogging feedrate in mm/min

panel.hotend_temperature                     185               # temp to set hotend when preheat is selected
panel.bed_temperature                        60                # temp to set bed when preheat is selected

# Example of a custom menu entry, which will show up in the Custom entry.
# NOTE _ gets converted to space in the menu and commands, | is used to separate multiple commands
custom_menu.power_on.enable                true              #
custom_menu.power_on.name                  Power_on          #
custom_menu.power_on.command               M80               #

custom_menu.power_off.enable               true              #
custom_menu.power_off.name                 Power_off         #
custom_menu.power_off.command              M81               #

# Only needed on a smoothieboard
currentcontrol_module_enable                 true             #

return_error_on_unhandled_gcode              false            #

# network settings
network.enable                               false            # enable the ethernet network services
network.webserver.enable                     true             # enable the webserver
network.telnet.enable                        true             # enable the telnet server
network.ip_address                           auto             # use dhcp to get ip address
# uncomment the 3 below to manually setup ip address
#network.ip_address                           192.168.3.222    # the IP address
#network.ip_mask                              255.255.255.0    # the ip mask
#network.ip_gateway                           192.168.3.1      # the gateway address
#network.mac_override                         xx.xx.xx.xx.xx.xx  # override the mac address, only do this if you have a conflict
Commit	Line	Data
bcb96295	1	# NOTE Lines must not exceed 132 characters
83f1253a MM	2	# Robot module configurations : general handling of movement G-codes and slicing into moves
	3	default_feed_rate 4000 # Default rate ( mm/minute ) for G1/G2/G3 moves
	4	default_seek_rate 4000 # Default rate ( mm/minute ) for G0 moves
a73d3197 JM	5	mm_per_arc_segment 0.5 # Arcs are cut into segments ( lines ), this is the length for
a73d3197 JM	6	# these segments. Smaller values mean more resolution,
bcb96295 JM	7	# higher values mean faster computation
	8	mm_per_line_segment 5 # Lines can be cut into segments ( not usefull with cartesian
	9	# coordinates robots ).
83f1253a MM	10
	11	# Arm solution configuration : Cartesian robot. Translates mm positions into stepper positions
	12	alpha_steps_per_mm 80 # Steps per mm for alpha stepper
	13	beta_steps_per_mm 80 # Steps per mm for beta stepper
	14	gamma_steps_per_mm 1600 # Steps per mm for gamma stepper
	15
	16	# Planner module configuration : Look-ahead and acceleration configuration
bcb96295	17	planner_queue_size 32 # DO NOT CHANGE THIS UNLESS YOU KNOW EXACTLY WHAT YOU ARE DOING
391d4ce8	18	acceleration 3000 # Acceleration in mm/second/second.
83f1253a	19	acceleration_ticks_per_second 1000 # Number of times per second the speed is updated
a73d3197	20	junction_deviation 0.05 # Similar to the old "max_jerk", in millimeters,
bcb96295 JM	21	# see https://github.com/grbl/grbl/blob/master/planner.c#L409
	22	# and https://github.com/grbl/grbl/wiki/Configuring-Grbl-v0.8
	23	# Lower values mean being more careful, higher values means being
	24	# faster and have more jerk
8b69c90d	25	#minimum_planner_speed 0.0 # sets the minimum planner speed in mm/sec
83f1253a MM	26
	27	# Stepper module configuration
	28	microseconds_per_step_pulse 1 # Duration of step pulses to stepper drivers, in microseconds
	29	minimum_steps_per_minute 1200 # Never step slower than this
1a534959	30	base_stepping_frequency 100000 # Base frequency for stepping, higher gives smoother movement
83f1253a	31
df6a30f2 MM	32	# Cartesian axis speed limits
	33	x_axis_max_speed 30000 # mm/min
	34	y_axis_max_speed 30000 # mm/min
	35	z_axis_max_speed 300 # mm/min
	36
83f1253a MM	37	# Stepper module pins ( ports, and pin numbers, appending "!" to the number will invert a pin )
	38	alpha_step_pin 2.0 # Pin for alpha stepper step signal
	39	alpha_dir_pin 0.5 # Pin for alpha stepper direction
	40	alpha_en_pin 0.4 # Pin for alpha enable pin
4fa40652	41	alpha_current 1.5 # X stepper motor current
df6a30f2	42	alpha_max_rate 30000.0 # mm/min
83f1253a MM	43
	44	beta_step_pin 2.1 # Pin for beta stepper step signal
	45	beta_dir_pin 0.11 # Pin for beta stepper direction
	46	beta_en_pin 0.10 # Pin for beta enable
4fa40652	47	beta_current 1.5 # Y stepper motor current
df6a30f2	48	beta_max_rate 30000.0 # mm/min
83f1253a MM	49
	50	gamma_step_pin 2.2 # Pin for gamma stepper step signal
	51	gamma_dir_pin 0.20 # Pin for gamma stepper direction
	52	gamma_en_pin 0.19 # Pin for gamma enable
4fa40652	53	gamma_current 1.5 # Z stepper motor current
df6a30f2	54	gamma_max_rate 300.0 # mm/min
83f1253a MM	55
83f1253a MM	56	# Serial communications configuration ( baud rate default to 9600 if undefined )
764b2de4	57	uart0.baud_rate 115200 # Baud rate for the default hardware serial port
a73d3197	58	second_usb_serial_enable false # This enables a second usb serial port (to have both pronterface
bcb96295	59	# and a terminal connected)
21320fc6 JM	60	#leds_disable true # disable using leds after config loaded
21320fc6 JM	61
83f1253a MM	62
83f1253a MM	63	# Extruder module configuration
c974b296 L	64	extruder.hotend.enable true # Whether to activate the extruder module at all. All configuration is ignored if false
	65	extruder.hotend.steps_per_mm 140 # Steps per mm for extruder stepper
	66	extruder.hotend.default_feed_rate 600 # Default rate ( mm/minute ) for moves where only the extruder moves
a73d3197 JM	67	extruder.hotend.acceleration 500 # Acceleration for the stepper motor, as of 0.6, arbitrary ratio
a73d3197 JM	68	extruder.hotend.max_speed 50 # mm/s
b0b47be7	69
c974b296 L	70	extruder.hotend.step_pin 2.3 # Pin for extruder step signal
	71	extruder.hotend.dir_pin 0.22 # Pin for extruder dir signal
	72	extruder.hotend.en_pin 0.21 # Pin for extruder enable signal
b0b47be7 L	73
b0b47be7 L	74	# for now the first extruder's offsets should be left at 0 or homing will get confused
fb307010 L	75	#extruder.hotend.x_offset 0 # x offset from origin in mm
	76	#extruder.hotend.y_offset 0 # y offset from origin in mm
	77	#extruder.hotend.z_offset 0 # z offset from origin in mm
b0b47be7 L	78
	79	delta_current 1.5 # First extruder stepper motor current
	80
	81	# Second extruder module configuration
c974b296 L	82	#extruder.hotend2.enable true # Whether to activate the extruder module at all. All configuration is ignored if false
	83	#extruder.hotend2.steps_per_mm 140 # Steps per mm for extruder stepper
	84	#extruder.hotend2.default_feed_rate 600 # Default rate ( mm/minute ) for moves where only the extruder moves
a73d3197 JM	85	#extruder.hotend2.acceleration 500 # Acceleration for the stepper motor, as of 0.6, arbitrary ratio
a73d3197 JM	86	#extruder.hotend2.max_speed 50 # mm/s
b0b47be7	87
c974b296 L	88	#extruder.hotend2.step_pin 2.8 # Pin for extruder step signal
	89	#extruder.hotend2.dir_pin 2.13 # Pin for extruder dir signal
	90	#extruder.hotend2.en_pin 4.29 # Pin for extruder enable signal
b0b47be7	91
84d5c1cb	92	#extruder.hotend2.x_offset 0 # x offset from origin in mm
fb307010	93	#extruder.hotend2.y_offset 25.0 # y offset from origin in mm
84d5c1cb	94	#extruder.hotend2.z_offset 0 # z offset from origin in mm
c974b296	95	#epsilon_current 1.5 # Second extruder stepper motor current
83f1253a MM	96
83f1253a MM	97	# Laser module configuration
a73d3197	98	laser_module_enable false # Whether to activate the laser module at all. All configuration is
bcb96295	99	# ignored if false.
a73d3197	100	#laser_module_pin 2.5 # this pin will be PWMed to control the laser. Only P2.0 - P2.5
bcb96295 JM	101	# can be used since laser requires hardware PWM
bcb96295 JM	102	#laser_module_max_power 0.8 # this is the maximum duty cycle that will be applied to the laser
a73d3197	103	#laser_module_tickle_power 0.0 # this duty cycle will be used for travel moves to keep the laser
bcb96295 JM	104	# active without actually burning
bcb96295 JM	105	#laser_module_pwm_period 20 # this sets the pwm frequency as the period in microseconds
83f1253a	106
fb307010	107	# Hotend temperature control configuration
a73d3197	108	temperature_control.hotend.enable true # Whether to activate this ( "hotend" ) module at all.
bcb96295	109	# All configuration is ignored if false.
6e36ad3c	110	temperature_control.hotend.link_to_tool true # This tells smoothie to enable and disable control of this hotend at the same time as the extruder of the same name
83f1253a	111	temperature_control.hotend.thermistor_pin 0.23 # Pin for the thermistor to read
fb307010	112	temperature_control.hotend.heater_pin 2.7 # Pin that controls the heater
bcb96295 JM	113	temperature_control.hotend.thermistor EPCOS100K # see src/modules/tools/temperaturecontrol/TemperatureControl.cpp:64
bcb96295 JM	114	# for a list of valid thermistor names
83f1253a MM	115	temperature_control.hotend.set_m_code 104 #
83f1253a MM	116	temperature_control.hotend.set_and_wait_m_code 109 #
fb307010	117	temperature_control.hotend.designator T #
84d5c1cb	118
fb307010 L	119	#temperature_control.hotend.p_factor 13.7 # permanently set the PID values after an auto pid
	120	#temperature_control.hotend.i_factor 0.097 #
	121	#temperature_control.hotend.d_factor 24 #
84d5c1cb	122
	123	#temperature_control.hotend.max_pwm 64 # max pwm, 64 is a good value if driving a 12v resistor with 24v.
	124
	125	# Hotend2 temperature control configuration
a73d3197	126	#temperature_control.hotend2.enable true # Whether to activate this ( "hotend" ) module at all.
84d5c1cb	127	# All configuration is ignored if false.
6e36ad3c	128	#temperature_control.hotend2.link_to_tool true # This tells smoothie to enable and disable control of this hotend at the same time as the extruder of the same name
84d5c1cb	129	#temperature_control.hotend2.thermistor_pin 0.25 # Pin for the thermistor to read
	130	#temperature_control.hotend2.heater_pin 1.23 # Pin that controls the heater
	131	#temperature_control.hotend2.thermistor EPCOS100K # see src/modules/tools/temperaturecontrol/TemperatureControl.cpp:64
	132	# for a list of valid thermistor names
	133	#temperature_control.hotend2.set_m_code 884 #
	134	#temperature_control.hotend2.set_and_wait_m_code 889 #
fb307010	135	#temperature_control.hotend2.designator T1 #
83f1253a	136
fb307010 L	137	#temperature_control.hotend2.p_factor 13.7 # permanently set the PID values after an auto pid
	138	#temperature_control.hotend2.i_factor 0.097 #
	139	#temperature_control.hotend2.d_factor 24 #
3617b234	140
bcb96295	141	#temperature_control.hotend.max_pwm 64 # max pwm, 64 is a good value if driving a 12v resistor with 24v.
3617b234	142
83f1253a MM	143	temperature_control.bed.enable true #
83f1253a MM	144	temperature_control.bed.thermistor_pin 0.24 #
83953434	145	temperature_control.bed.heater_pin 2.5 #
bcb96295 JM	146	temperature_control.bed.thermistor Honeywell100K # see src/modules/tools/temperaturecontrol/TemperatureControl.cpp:64
bcb96295 JM	147	# for a list of valid thermistor names
83f1253a MM	148	temperature_control.bed.set_m_code 140 #
83f1253a MM	149	temperature_control.bed.set_and_wait_m_code 190 #
4ade0e35	150	temperature_control.bed.designator B #
83f1253a	151
bcb96295 JM	152	#temperature_control.bed.bang_bang false # set to true to use bang bang control rather than PID
	153	#temperature_control.bed.hysteresis 2.0 # set to the temperature in degrees C to use as hysteresis
	154	# when using bang bang
989d0e94	155
83f1253a MM	156	# Switch module for fan control
83f1253a MM	157	switch.fan.enable true #
a044ee23 L	158	switch.fan.input_on_command M106 #
a044ee23 L	159	switch.fan.input_off_command M107 #
83f1253a	160	switch.fan.output_pin 2.6 #
e9f88113	161	switch.fan.output_type pwm # pwm output settable with S parameter in the input_on_comand
ef318bf8	162	#switch.fan.max_pwm 255 # set max pwm for the pin default is 255
83f1253a	163
a044ee23 L	164	#switch.misc.enable true #
	165	#switch.misc.input_on_command M42 #
	166	#switch.misc.input_off_command M43 #
	167	#switch.misc.output_pin 2.4 #
e9f88113	168	#switch.misc.output_type digital # just an on or off pin
83f1253a MM	169
83f1253a MM	170	# Switch module for spindle control
a044ee23	171	#switch.spindle.enable false #
83f1253a MM	172
83f1253a MM	173	# Endstops
3f92b681	174	endstops_enable true # the endstop module is enabled by default and can be disabled here
e367bd54	175	#corexy_homing false # set to true if homing on a hbit or corexy
821587de	176	alpha_min_endstop 1.24^ # add a ! to invert if endstop is NO connected to ground
0c6616d1	177	alpha_max_endstop 1.25^ #
a64e8935 JM	178	alpha_homing_direction home_to_min # or set to home_to_max and set alpha_max
	179	alpha_min 0 # this gets loaded after homing when home_to_min is set
	180	alpha_max 200 # this gets loaded after homing when home_to_max is set
0c6616d1 A	181	beta_min_endstop 1.26^ #
0c6616d1 A	182	beta_max_endstop 1.27^ #
409ff5b3	183	beta_homing_direction home_to_min #
3ffe27fb AV	184	beta_min 0 #
3ffe27fb AV	185	beta_max 200 #
0c6616d1 A	186	gamma_min_endstop 1.28^ #
0c6616d1 A	187	gamma_max_endstop 1.29^ #
409ff5b3	188	gamma_homing_direction home_to_min #
3ffe27fb AV	189	gamma_min 0 #
3ffe27fb AV	190	gamma_max 200 #
83f1253a	191
5de98d7c JM	192	alpha_fast_homing_rate_mm_s 50 # feedrates in mm/second
	193	beta_fast_homing_rate_mm_s 50 # "
	194	gamma_fast_homing_rate_mm_s 4 # "
	195	alpha_slow_homing_rate_mm_s 25 # "
	196	beta_slow_homing_rate_mm_s 25 # "
	197	gamma_slow_homing_rate_mm_s 2 # "
a803eb76	198
5de98d7c JM	199	alpha_homing_retract_mm 5 # distance in mm
	200	beta_homing_retract_mm 5 # "
	201	gamma_homing_retract_mm 1 # "
a803eb76	202
c45f5011 JM	203	#endstop_debounce_count 100 # uncomment if you get noise on your endstops
c45f5011 JM	204
a803eb76 JM	205	# Pause button
	206	pause_button_enable true #
	207
83f1253a	208	# Panel
1a23a9c7	209	panel.enable false # set to true to enable the panel code
a73d3197	210	panel.lcd smoothiepanel # set type of panel
f2811cc5 JM	211	panel.encoder_a_pin 3.25!^ # encoder pin
f2811cc5 JM	212	panel.encoder_b_pin 3.26!^ # encoder pin
19fb4629	213
af301cc4	214	# Example for reprap discount GLCD
5de98d7c	215	# on glcd EXP1 is to left and EXP2 is to right, pin 1 is bottom left, pin 2 is top left etc.
bb5d4dd1 JM	216	# +5v is EXP1 pin 10, Gnd is EXP1 pin 9
	217	#panel.lcd reprap_discount_glcd #
	218	#panel.spi_channel 0 # spi channel to use ; GLCD EXP1 Pins 3,5 (MOSI, SCLK)
	219	#panel.spi_cs_pin 0.16 # spi chip select ; GLCD EXP1 Pin 4
f2811cc5 JM	220	#panel.encoder_a_pin 3.25!^ # encoder pin ; GLCD EXP2 Pin 3
f2811cc5 JM	221	#panel.encoder_b_pin 3.26!^ # encoder pin ; GLCD EXP2 Pin 5
5de98d7c	222	#panel.click_button_pin 1.30!^ # click button ; GLCD EXP1 Pin 2
bb5d4dd1	223	#panel.buzz_pin 1.31 # pin for buzzer ; GLCD EXP1 Pin 1
c9fcf59a JM	224	#panel.button_pause_pin 2.11^ # kill/pause ; GLCD EXP2 Pin 8 either
c9fcf59a JM	225	#panel.back_button_pin 2.11!^ # back button ; GLCD EXP2 Pin 8 or
bb5d4dd1 JM	226
bb5d4dd1 JM	227	# pins used with other panels
35089dc7 JM	228	#panel.up_button_pin 0.1! # up button if used
	229	#panel.down_button_pin 0.0! # down button if used
	230	#panel.click_button_pin 0.18! # click button if used
	231
f597c052 JM	232	panel.menu_offset 0 # some panels will need 1 here
f597c052 JM	233
35089dc7 JM	234	panel.alpha_jog_feedrate 6000 # x jogging feedrate in mm/min
	235	panel.beta_jog_feedrate 6000 # y jogging feedrate in mm/min
	236	panel.gamma_jog_feedrate 200 # z jogging feedrate in mm/min
83f1253a	237
1065cae0 JM	238	panel.hotend_temperature 185 # temp to set hotend when preheat is selected
	239	panel.bed_temperature 60 # temp to set bed when preheat is selected
	240
21320fc6	241	# Example of a custom menu entry, which will show up in the Custom entry.
5ff3e912	242	# NOTE _ gets converted to space in the menu and commands, \| is used to separate multiple commands
ca6effd7 JM	243	custom_menu.power_on.enable true #
	244	custom_menu.power_on.name Power_on #
	245	custom_menu.power_on.command M80 #
	246
	247	custom_menu.power_off.enable true #
	248	custom_menu.power_off.name Power_off #
	249	custom_menu.power_off.command M81 #
	250
83f1253a MM	251	# Only needed on a smoothieboard
83f1253a MM	252	currentcontrol_module_enable true #
74b6303c	253
b03b17d7	254	return_error_on_unhandled_gcode false #
74b6303c	255
d4ee6ee2 JM	256	# network settings
	257	network.enable false # enable the ethernet network services
	258	network.webserver.enable true # enable the webserver
	259	network.telnet.enable true # enable the telnet server
	260	network.ip_address auto # use dhcp to get ip address
989d0e94	261	# uncomment the 3 below to manually setup ip address
d4ee6ee2 JM	262	#network.ip_address 192.168.3.222 # the IP address
	263	#network.ip_mask 255.255.255.0 # the ip mask
	264	#network.ip_gateway 192.168.3.1 # the gateway address
	265	#network.mac_override xx.xx.xx.xx.xx.xx # override the mac address, only do this if you have a conflict