1 # Robot module configurations : general handling of movement G-codes and slicing into moves
2 default_feed_rate 4000 # Default rate ( mm/minute ) for G1/G2/G3 moves
3 default_seek_rate 4000 # Default rate ( mm/minute ) for G0 moves
4 mm_per_arc_segment 0.0 # Fixed length for line segments that divide arcs 0 to disable
5 mm_max_arc_error 0.01 # The maximum error for line segments that divide arcs 0 to disable
6 # note it is invalid for both the above be 0
7 # if both are used, will use largest segment length based on radius
8 #mm_per_line_segment 5 # Lines can be cut into segments ( not usefull with cartesian coordinates robots ).
10 # Arm solution configuration : Cartesian robot. Translates mm positions into stepper positions
11 alpha_steps_per_mm 80 # Steps per mm for alpha stepper
12 beta_steps_per_mm 80 # Steps per mm for beta stepper
13 gamma_steps_per_mm 1637.7953 # Steps per mm for gamma stepper
15 # Planner module configuration : Look-ahead and acceleration configuration
16 planner_queue_size 32 # DO NOT CHANGE THIS UNLESS YOU KNOW EXACTLY WHAT YOUR ARE DOING
17 acceleration 3000 # Acceleration in mm/second/second.
18 #z_acceleration 500 # Acceleration for Z only moves in mm/s^2, 0 disables it, disabled by default. DO NOT SET ON A DELTA
19 acceleration_ticks_per_second 1000 # Number of times per second the speed is updated
20 junction_deviation 0.05 # Similar to the old "max_jerk", in millimeters, see : https://github.com/grbl/grbl/blob/master/planner.c#L409
21 # and https://github.com/grbl/grbl/wiki/Configuring-Grbl-v0.8 . Lower values mean being more careful, higher values means being faster and have more jerk
23 # Stepper module configuration
24 microseconds_per_step_pulse 1 # Duration of step pulses to stepper drivers, in microseconds
25 base_stepping_frequency 100000 # Base frequency for stepping
27 # Stepper module pins ( ports, and pin numbers, appending "!" to the number will invert a pin )
28 alpha_step_pin 2.1 # Pin for alpha stepper step signal
29 alpha_dir_pin 0.11 # Pin for alpha stepper direction
30 alpha_en_pin 0.10 # Pin for alpha enable pin
31 alpha_current 1.0 # X stepper motor current
32 x_axis_max_speed 30000 # mm/min
33 alpha_max_rate 30000.0 # mm/min actuator max speed
35 beta_step_pin 2.2 # Pin for beta stepper step signal
36 beta_dir_pin 0.20 # Pin for beta stepper direction
37 beta_en_pin 0.19 # Pin for beta enable
38 beta_current 1.0 # Y stepper motor current
39 y_axis_max_speed 30000 # mm/min
40 beta_max_rate 30000.0 # mm/min actuator max speed
42 gamma_step_pin 2.3 # Pin for gamma stepper step signal
43 gamma_dir_pin 0.22 # Pin for gamma stepper direction
44 gamma_en_pin 0.21 # Pin for gamma enable
45 gamma_current 1.0 # Z stepper motor current
46 z_axis_max_speed 300 # mm/min
47 gamma_max_rate 300.0 # mm/min actuator max speed
49 # Serial communications configuration ( baud rate default to 9600 if undefined )
50 uart0.baud_rate 115200 # Baud rate for the default hardware serial port
51 second_usb_serial_enable false # This enables a second usb serial port (to have both pronterface and a terminal connected)
53 #msd_disable false # disable the MSD (USB SDCARD) when set to true
54 #leds_disable true # disable using leds after config loaded
55 #dfu_enable false # for linux developers, set to true to enable DFU
56 #watchdog_timeout 10 # watchdog timeout in seconds, default is 10, set to 0 to disable the watchdog
58 # Extruder module configuration
59 extruder_module_enable true # Whether to activate the extruder module at all. All configuration is ignored if false
60 extruder_steps_per_mm 140 # Steps per mm for extruder stepper
61 extruder_default_feed_rate 600 # Default rate ( mm/minute ) for moves where only the extruder moves
62 extruder_acceleration 500 # Acceleration in mm/sec^2, only used for retracts
63 extruder_max_speed 1000 # mm/sec NOTE only used for retracts
65 extruder_step_pin 2.0 # Pin for extruder step signal
66 extruder_dir_pin 0.5 # Pin for extruder dir signal
67 extruder_en_pin 0.4 # Pin for extruder enable signal
68 delta_current 1.0 # Extruder stepper motor current
70 # Laser module configuration
71 laser_module_enable false # Whether to activate the laser module at all. All configuration is
73 #laser_module_pin 2.5 # this pin will be PWMed to control the laser. Only P2.0 - P2.5, P1.18, P1.20, P1.21, P1.23, P1.24, P1.26, P3.25, P3.26
74 # can be used since laser requires hardware PWM
75 #laser_module_maximum_power 1.0 # this is the maximum duty cycle that will be applied to the laser
76 #laser_module_minimum_power 0.0 # This is a value just below the minimum duty cycle that keeps the laser
77 # active without actually burning.
78 #laser_module_default_power 0.8 # This is the default laser power that will be used for cuts if a power has not been specified. The value is a scale between
79 # the maximum and minimum power levels specified above
80 #laser_module_pwm_period 20 # this sets the pwm frequency as the period in microseconds
82 # Hotend temperature control configuration
83 temperature_control.hotend.enable true # Whether to activate this ( "hotend" ) module at all. All configuration is ignored if false.
84 temperature_control.hotend.thermistor_pin 0.24 # Pin for the thermistor to read
85 temperature_control.hotend.heater_pin 2.5 # Pin that controls the heater
86 temperature_control.hotend.thermistor EPCOS100K # see http://smoothieware.org/temperaturecontrol#toc5
87 #temperature_control.hotend.beta 4066 # or set the beta value
89 temperature_control.hotend.set_m_code 104 #
90 temperature_control.hotend.set_and_wait_m_code 109 #
91 temperature_control.hotend.designator T #
92 #temperature_control.hotend.max_temp 300 # Set maximum temperature - Will prevent heating above 300 by default
93 #temperature_control.hotend.min_temp 0 # Set minimum temperature - Will prevent heating below 0 by default
95 temperature_control.hotend.p_factor 13.7 #
96 temperature_control.hotend.i_factor 0.097 #
97 temperature_control.hotend.d_factor 24 #
99 temperature_control.bed.enable false #
100 temperature_control.bed.thermistor_pin 0.23 #
101 temperature_control.bed.heater_pin 2.7 #
102 temperature_control.bed.thermistor Honeywell100K # see http://smoothieware.org/temperaturecontrol#toc5
103 #temperature_control.bed.beta 4066 # or set the beta value
105 temperature_control.bed.set_m_code 140 #
106 temperature_control.bed.set_and_wait_m_code 190 #
107 temperature_control.bed.designator B #
109 # Switch module for fan control
110 switch.fan.enable true #
111 switch.fan.input_on_command M106 #
112 switch.fan.input_off_command M107 #
113 switch.fan.output_pin 2.4 #
115 switch.misc.enable false #
116 switch.misc.input_on_command M42 #
117 switch.misc.input_off_command M43 #
118 switch.misc.output_pin 2.4 #
120 # automatically toggle a switch at a specified temperature. Different ones of these may be defined to monitor different temperatures and switch different swithxes
121 # useful to turn on a fan or water pump to cool the hotend
122 #temperatureswitch.hotend.enable true #
123 #temperatureswitch.hotend.designator T # first character of the temperature control designator to use as the temperature sensor to monitor
124 #temperatureswitch.hotend.switch misc # select which switch to use, matches the name of the defined switch
125 #temperatureswitch.hotend.threshold_temp 60.0 # temperature to turn on (if rising) or off the switch
126 #temperatureswitch.hotend.heatup_poll 15 # poll heatup at 15 sec intervals
127 #temperatureswitch.hotend.cooldown_poll 60 # poll cooldown at 60 sec intervals
129 # filament out detector
130 #filament_detector.enable true #
131 #filament_detector.encoder_pin 0.26 # must be interrupt enabled pin (0.26, 0.27, 0.28)
132 #filament_detector.seconds_per_check 2 # may need to be longer
133 #filament_detector.pulses_per_mm 1 .0 # will need to be tuned
134 #filament_detector.bulge_pin 0.27 # optional bulge detector switch and/or manual suspend
136 # Switch module for spindle control
137 #switch.spindle.enable false #
140 endstops_enable true # the endstop module is enabled by default and can be disabled here
141 #corexy_homing false # set to true if homing on a hbit or corexy
142 alpha_min_endstop 1.24^ # add a ! to invert if endstop is NO connected to ground
143 #alpha_max_endstop 1.24^ #
144 alpha_homing_direction home_to_min # or set to home_to_max and set alpha_max
145 alpha_min 0 # this gets loaded after homing when home_to_min is set
146 alpha_max 200 # this gets loaded after homing when home_to_max is set
147 beta_min_endstop 1.26^ #
148 #beta_max_endstop 1.26^ #
149 beta_homing_direction home_to_min #
152 gamma_min_endstop 1.28^ #
153 #gamma_max_endstop 1.28^ #
154 gamma_homing_direction home_to_min #
158 # optional enable limit switches, actions will stop if any enabled limit switch is triggered
159 #alpha_limit_enable false # set to true to enable X min and max limit switches
160 #beta_limit_enable false # set to true to enable Y min and max limit switches
161 #gamma_limit_enable false # set to true to enable Z min and max limit switches
162 #move_to_origin_after_home false # move XY to 0,0 after homing
165 #probe_pin 1.29 # optional pin for probe
167 alpha_fast_homing_rate_mm_s 50 # feedrates in mm/second
168 beta_fast_homing_rate_mm_s 50 # "
169 gamma_fast_homing_rate_mm_s 4 # "
170 alpha_slow_homing_rate_mm_s 25 # "
171 beta_slow_homing_rate_mm_s 25 # "
172 gamma_slow_homing_rate_mm_s 2 # "
174 alpha_homing_retract_mm 5 # distance in mm
175 beta_homing_retract_mm 5 # "
176 gamma_homing_retract_mm 1 # "
178 #endstop_debounce_count 100 # uncomment if you get noise on your endstops, default is 100
181 zprobe.enable false # set to true to enable a zprobe
182 zprobe.probe_pin 1.29!^ # pin probe is attached to if NC remove the !
183 zprobe.slow_feedrate 5 # mm/sec probe feed rate
184 #zprobe.debounce_count 100 # set if noisy
185 zprobe.fast_feedrate 100 # move feedrate mm/sec
186 zprobe.probe_height 5 # how much above bed to start probe
188 # associated with zprobe the leveling strategy to use
189 #leveling-strategy.three-point-leveling.enable true # a leveling strategy that probes three points to define a plane and keeps the Z parallel to that plane
190 #leveling-strategy.three-point-leveling.point1 100.0,0.0 # the first probe point (x,y) optional may be defined with M557
191 #leveling-strategy.three-point-leveling.point2 200.0,200.0 # the second probe point (x,y)
192 #leveling-strategy.three-point-leveling.point3 0.0,200.0 # the third probe point (x,y)
193 #leveling-strategy.three-point-leveling.home_first true # home the XY axis before probing
194 #leveling-strategy.three-point-leveling.tolerance 0.03 # the probe tolerance in mm, anything less that this will be ignored, default is 0.03mm
195 #leveling-strategy.three-point-leveling.probe_offsets 0,0,0 # the probe offsets from nozzle, must be x,y,z, default is no offset
196 #leveling-strategy.three-point-leveling.save_plane false # set to true to allow the bed plane to be saved with M500 default is false
199 # kill button (used to be called pause) maybe assigned to a different pin, set to the onboard pin by default
200 kill_button_enable true # set to true to enable a kill button
201 kill_button_pin 2.12 # kill button pin. default is same as pause button 2.12 (2.11 is another good choice)
203 # Panel See http://smoothieware.org/panel
204 panel.enable false # set to true to enable the panel code
206 # Example viki2 config for an azteeg miniV2 with IDC cable
207 panel.lcd viki2 # set type of panel
208 panel.spi_channel 0 # set spi channel to use P0_18,P0_15 MOSI,SCLK
209 panel.spi_cs_pin 0.16 # set spi chip select
210 panel.encoder_a_pin 3.25!^ # encoder pin
211 panel.encoder_b_pin 3.26!^ # encoder pin
212 panel.click_button_pin 2.11!^ # click button
213 panel.a0_pin 2.6 # st7565 needs an a0
214 #panel.contrast 8 # override contrast setting (default is 9)
215 #panel.encoder_resolution 4 # override number of clicks to move 1 item (default is 4)
216 #panel.button_pause_pin 1.22^ # kill/pause set one of these for the auxilliary button on viki2
217 #panel.back_button_pin 1.22!^ # back button recommended to use this on EXP1
218 panel.buzz_pin 0.25 # pin for buzzer on EXP2
219 panel.red_led_pin 2.8 # pin for red led on viki2 on EXP1
220 panel.blue_led_pin 4.29 # pin for blue led on viki2 on EXP1
221 panel.external_sd true # set to true if there is an extrernal sdcard on the panel
222 panel.external_sd.spi_channel 0 # set spi channel the sdcard is on
223 panel.external_sd.spi_cs_pin 1.23 # set spi chip select for the sdcard
224 panel.external_sd.sdcd_pin 1.31!^ # sd detect signal (set to nc if no sdcard detect)
225 panel.menu_offset 1 # some panels will need 1 here
227 # Example miniviki2 config
228 #panel.lcd mini_viki2 # set type of panel
229 #panel.spi_channel 0 # set spi channel to use P0_18,P0_15 MOSI,SCLK
230 #panel.spi_cs_pin 0.16 # set spi chip select
231 #panel.encoder_a_pin 3.25!^ # encoder pin
232 #panel.encoder_b_pin 3.26!^ # encoder pin
233 #panel.click_button_pin 2.11!^ # click button
234 #panel.a0_pin 2.6 # st7565 needs an a0
235 ##panel.contrast 18 # override contrast setting (default is 18)
236 ##panel.encoder_resolution 2 # override number of clicks to move 1 item (default is 2)
237 #panel.menu_offset 1 # here controls how sensitive the menu is. some panels will need 1
239 panel.alpha_jog_feedrate 6000 # x jogging feedrate in mm/min
240 panel.beta_jog_feedrate 6000 # y jogging feedrate in mm/min
241 panel.gamma_jog_feedrate 200 # z jogging feedrate in mm/min
243 panel.hotend_temperature 185 # temp to set hotend when preheat is selected
244 panel.bed_temperature 60 # temp to set bed when preheat is selected
246 # Example of a custom menu entry, which will show up in the Custom entry.
247 # NOTE _ gets converted to space in the menu and commands, | is used to separate multiple commands
248 custom_menu.power_on.enable true #
249 custom_menu.power_on.name Power_on #
250 custom_menu.power_on.command M80 #
252 custom_menu.power_off.enable true #
253 custom_menu.power_off.name Power_off #
254 custom_menu.power_off.command M81 #
256 # Azteeg specific settings do not change
257 currentcontrol_module_enable true #
258 digipot_max_current 2.4 # max current
259 digipot_factor 106.0 # factor for converting current to digipot value
HCoop / clinton / Smoothieware.git / blob