keyboards/keebio/fourier/rules.mk

   1 # MCU name
   2 MCU = atmega32u4
   3
   4 # Processor frequency.
   5 #     This will define a symbol, F_CPU, in all source code files equal to the
   6 #     processor frequency in Hz. You can then use this symbol in your source code to
   7 #     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
   8 #     automatically to create a 32-bit value in your source code.
   9 #
  10 #     This will be an integer division of F_USB below, as it is sourced by
  11 #     F_USB after it has run through any CPU prescalers. Note that this value
  12 #     does not *change* the processor frequency - it should merely be updated to
  13 #     reflect the processor speed set externally so that the code can use accurate
  14 #     software delays.
  15 F_CPU = 16000000
  16
  17 #
  18 # LUFA specific
  19 #
  20 # Target architecture (see library "Board Types" documentation).
  21 ARCH = AVR8
  22
  23 # Input clock frequency.
  24 #     This will define a symbol, F_USB, in all source code files equal to the
  25 #     input clock frequency (before any prescaling is performed) in Hz. This value may
  26 #     differ from F_CPU if prescaling is used on the latter, and is required as the
  27 #     raw input clock is fed directly to the PLL sections of the AVR for high speed
  28 #     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
  29 #     at the end, this will be done automatically to create a 32-bit value in your
  30 #     source code.
  31 #
  32 #     If no clock division is performed on the input clock inside the AVR (via the
  33 #     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
  34 F_USB = $(F_CPU)
  35
  36 # Bootloader
  37 #     This definition is optional, and if your keyboard supports multiple bootloaders of
  38 #     different sizes, comment this out, and the correct address will be loaded
  39 #     automatically (+60). See bootloader.mk for all options.
  40 BOOTLOADER = caterina
  41
  42 # Interrupt driven control endpoint task(+60)
  43 OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
  44
  45 # Build Options
  46 #   change to "no" to disable the options, or define them in the Makefile in
  47 #   the appropriate keymap folder that will get included automatically
  48 #
  49 BOOTMAGIC_ENABLE = no       # Virtual DIP switch configuration(+1000)
  50 MOUSEKEY_ENABLE = no        # Mouse keys(+4700)
  51 EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
  52 CONSOLE_ENABLE = no         # Console for debug(+400)
  53 COMMAND_ENABLE = yes        # Commands for debug and configuration
  54 NKRO_ENABLE = no            # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
  55 BACKLIGHT_ENABLE = no       # Enable keyboard backlight functionality
  56 MIDI_ENABLE = no            # MIDI controls
  57 AUDIO_ENABLE = no           # Audio output on port C6
  58 UNICODE_ENABLE = no         # Unicode
  59 BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
  60 RGBLIGHT_ENABLE = yes        # Enable WS2812 RGB underlight.
  61
  62 # Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
  63 SLEEP_LED_ENABLE = no    # Breathing sleep LED during USB suspend
  64
  65 SPLIT_KEYBOARD = yes