keyboards/wilba_tech/rama_works_m6_b/rules.mk

   1 # project specific files
   2 SRC =   keyboards/wilba_tech/wt_main.c \
   3                 keyboards/wilba_tech/wt_rgb_backlight.c \
   4                 quantum/color.c \
   5                 drivers/issi/is31fl3218.c \
   6                 drivers/avr/i2c_master.c
   7
   8
   9 # MCU name
  10 MCU = atmega32u4
  11
  12 # Processor frequency.
  13 #     This will define a symbol, F_CPU, in all source code files equal to the
  14 #     processor frequency in Hz. You can then use this symbol in your source code to
  15 #     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
  16 #     automatically to create a 32-bit value in your source code.
  17 #
  18 #     This will be an integer division of F_USB below, as it is sourced by
  19 #     F_USB after it has run through any CPU prescalers. Note that this value
  20 #     does not *change* the processor frequency - it should merely be updated to
  21 #     reflect the processor speed set externally so that the code can use accurate
  22 #     software delays.
  23 F_CPU = 16000000
  24
  25
  26 #
  27 # LUFA specific
  28 #
  29 # Target architecture (see library "Board Types" documentation).
  30 ARCH = AVR8
  31
  32 # Input clock frequency.
  33 #     This will define a symbol, F_USB, in all source code files equal to the
  34 #     input clock frequency (before any prescaling is performed) in Hz. This value may
  35 #     differ from F_CPU if prescaling is used on the latter, and is required as the
  36 #     raw input clock is fed directly to the PLL sections of the AVR for high speed
  37 #     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
  38 #     at the end, this will be done automatically to create a 32-bit value in your
  39 #     source code.
  40 #
  41 #     If no clock division is performed on the input clock inside the AVR (via the
  42 #     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
  43 F_USB = $(F_CPU)
  44
  45 # Interrupt driven control endpoint task(+60)
  46 OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
  47
  48 # Boot Section
  49 BOOTLOADER = atmel-dfu
  50
  51 # Do not put the microcontroller into power saving mode
  52 # when we get USB suspend event. We want it to keep updating
  53 # backlight effects.
  54 OPT_DEFS += -DNO_SUSPEND_POWER_DOWN
  55
  56
  57 # Build Options
  58 #   change yes to no to disable
  59 #
  60 BOOTMAGIC_ENABLE = no       # Virtual DIP switch configuration(+1000)
  61 MOUSEKEY_ENABLE = no       # Mouse keys(+4700)
  62 EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
  63 CONSOLE_ENABLE = no         # Console for debug(+400)
  64 COMMAND_ENABLE = no        # Commands for debug and configuration
  65 NKRO_ENABLE = yes            # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
  66 BACKLIGHT_ENABLE = no      # Enable keyboard backlight functionality
  67 MIDI_ENABLE = no            # MIDI controls
  68 AUDIO_ENABLE = no           # Audio output on port C6
  69 UNICODE_ENABLE = no         # Unicode
  70 BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
  71 RGBLIGHT_ENABLE = no        # Enable WS2812 RGB underlight.  Do not enable this with audio at the same time.
  72
  73 # Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
  74 SLEEP_LED_ENABLE = no    # Breathing sleep LED during USB suspend
  75
  76 RAW_ENABLE = yes
  77 DYNAMIC_KEYMAP_ENABLE = yes
  78 CIE1931_CURVE = yes
  79