keyboards/lets_split/rules.mk

   1 SRC += matrix.c \
   2            i2c.c \
   3            split_util.c \
   4            serial.c
   5
   6 # MCU name
   7 #MCU = at90usb1287
   8 MCU = atmega32u4
   9
  10 # Processor frequency.
  11 #     This will define a symbol, F_CPU, in all source code files equal to the
  12 #     processor frequency in Hz. You can then use this symbol in your source code to
  13 #     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
  14 #     automatically to create a 32-bit value in your source code.
  15 #
  16 #     This will be an integer division of F_USB below, as it is sourced by
  17 #     F_USB after it has run through any CPU prescalers. Note that this value
  18 #     does not *change* the processor frequency - it should merely be updated to
  19 #     reflect the processor speed set externally so that the code can use accurate
  20 #     software delays.
  21 F_CPU = 16000000
  22
  23 #
  24 # LUFA specific
  25 #
  26 # Target architecture (see library "Board Types" documentation).
  27 ARCH = AVR8
  28
  29 # Input clock frequency.
  30 #     This will define a symbol, F_USB, in all source code files equal to the
  31 #     input clock frequency (before any prescaling is performed) in Hz. This value may
  32 #     differ from F_CPU if prescaling is used on the latter, and is required as the
  33 #     raw input clock is fed directly to the PLL sections of the AVR for high speed
  34 #     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
  35 #     at the end, this will be done automatically to create a 32-bit value in your
  36 #     source code.
  37 #
  38 #     If no clock division is performed on the input clock inside the AVR (via the
  39 #     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
  40 F_USB = $(F_CPU)
  41
  42 # Interrupt driven control endpoint task(+60)
  43 OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
  44
  45
  46 # Boot Section Size in *bytes*
  47 #   Teensy halfKay   512
  48 #   Teensy++ halfKay 1024
  49 #   Atmel DFU loader 4096
  50 #   LUFA bootloader  4096
  51 #   USBaspLoader     2048
  52 OPT_DEFS += -DBOOTLOADER_SIZE=4096
  53
  54 # Build Options
  55 #   change to "no" to disable the options, or define them in the Makefile in
  56 #   the appropriate keymap folder that will get included automatically
  57 #
  58 BOOTMAGIC_ENABLE ?= no       # Virtual DIP switch configuration(+1000)
  59 MOUSEKEY_ENABLE ?= yes       # Mouse keys(+4700)
  60 EXTRAKEY_ENABLE ?= yes       # Audio control and System control(+450)
  61 CONSOLE_ENABLE ?= no         # Console for debug(+400)
  62 COMMAND_ENABLE ?= yes        # Commands for debug and configuration
  63 NKRO_ENABLE ?= no            # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
  64 BACKLIGHT_ENABLE ?= no      # Enable keyboard backlight functionality
  65 MIDI_ENABLE ?= no            # MIDI controls
  66 AUDIO_ENABLE ?= no           # Audio output on port C6
  67 UNICODE_ENABLE ?= no         # Unicode
  68 BLUETOOTH_ENABLE ?= no       # Enable Bluetooth with the Adafruit EZ-Key HID
  69 RGBLIGHT_ENABLE ?= no       # Enable WS2812 RGB underlight.  Do not enable this with audio at the same time.
  70 SUBPROJECT_rev1 ?= yes
  71 USE_I2C ?= yes
  72 # Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
  73 SLEEP_LED_ENABLE ?= no    # Breathing sleep LED during USB suspend
  74
  75 CUSTOM_MATRIX = yes
  76
  77 avrdude: build
  78         ls /dev/tty* > /tmp/1; \
  79         echo "Reset your Pro Micro then hit any key to continue..."; \
  80         read -n 1 -s; \
  81         ls /dev/tty* > /tmp/2; \
  82         USB=`diff /tmp/1 /tmp/2 | grep '>' | sed -e 's/> //'`; \
  83         avrdude -p $(MCU) -c avr109 -P $$USB -U flash:w:$(BUILD_DIR)/$(TARGET).hex
  84
  85 .PHONY: avrdude