keyboards/daisy/rules.mk

   1 # MCU name
   2 #MCU = at90usb1286
   3 MCU = atmega32u4
   4
   5 # Processor frequency.
   6 #     This will define a symbol, F_CPU, in all source code files equal to the
   7 #     processor frequency in Hz. You can then use this symbol in your source code to
   8 #     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
   9 #     automatically to create a 32-bit value in your source code.
  10 #
  11 #     This will be an integer division of F_USB below, as it is sourced by
  12 #     F_USB after it has run through any CPU prescalers. Note that this value
  13 #     does not *change* the processor frequency - it should merely be updated to
  14 #     reflect the processor speed set externally so that the code can use accurate
  15 #     software delays.
  16 F_CPU = 16000000
  17
  18
  19 #
  20 # LUFA specific
  21 #
  22 # Target architecture (see library "Board Types" documentation).
  23 ARCH = AVR8
  24
  25 # Input clock frequency.
  26 #     This will define a symbol, F_USB, in all source code files equal to the
  27 #     input clock frequency (before any prescaling is performed) in Hz. This value may
  28 #     differ from F_CPU if prescaling is used on the latter, and is required as the
  29 #     raw input clock is fed directly to the PLL sections of the AVR for high speed
  30 #     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
  31 #     at the end, this will be done automatically to create a 32-bit value in your
  32 #     source code.
  33 #
  34 #     If no clock division is performed on the input clock inside the AVR (via the
  35 #     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
  36 F_USB = $(F_CPU)
  37
  38 # Interrupt driven control endpoint task(+60)
  39 OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
  40
  41
  42 # Boot Section Size in *bytes*
  43 #   Teensy halfKay   512
  44 #   Teensy++ halfKay 1024
  45 #   Atmel DFU loader 4096
  46 #   LUFA bootloader  4096
  47 #   USBaspLoader     2048
  48 OPT_DEFS += -DBOOTLOADER_SIZE=4996
  49
  50 # QMK Build Options
  51 #   change to "no" to disable the options, or define them in the Makefile in
  52 #   the appropriate keymap folder that will get included automatically
  53 #
  54 BOOTMAGIC_ENABLE = no       # Virtual DIP switch configuration(+1000)
  55 MOUSEKEY_ENABLE = no        # Mouse keys(+4700)
  56 EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
  57 CONSOLE_ENABLE = no         # Console for debug(+400)
  58 COMMAND_ENABLE = no         # Commands for debug and configuration
  59 NKRO_ENABLE = yes           # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
  60 BACKLIGHT_ENABLE = yes      # Enable keyboard backlight functionality
  61 MIDI_ENABLE = no            # MIDI support (+2400 to 4200, depending on config)
  62 AUDIO_ENABLE = no           # Audio output on port C6
  63 UNICODE_ENABLE = no         # Unicode
  64 BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
  65 RGBLIGHT_ENABLE = yes       # Enable WS2812 RGB underlight.  Do not enable this with audio at the same time.
  66 SLEEP_LED_ENABLE = no       # Breathing sleep LED during USB suspend