keyboards/lets_split/rules.mk

   1 SRC += matrix.c \
   2            i2c.c \
   3            split_util.c \
   4            serial.c\
   5            ssd1306.c
   6
   7 # MCU name
   8 #MCU = at90usb1287
   9 MCU = atmega32u4
  10
  11 # Processor frequency.
  12 #     This will define a symbol, F_CPU, in all source code files equal to the
  13 #     processor frequency in Hz. You can then use this symbol in your source code to
  14 #     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
  15 #     automatically to create a 32-bit value in your source code.
  16 #
  17 #     This will be an integer division of F_USB below, as it is sourced by
  18 #     F_USB after it has run through any CPU prescalers. Note that this value
  19 #     does not *change* the processor frequency - it should merely be updated to
  20 #     reflect the processor speed set externally so that the code can use accurate
  21 #     software delays.
  22 F_CPU = 16000000
  23
  24 #
  25 # LUFA specific
  26 #
  27 # Target architecture (see library "Board Types" documentation).
  28 ARCH = AVR8
  29
  30 # Input clock frequency.
  31 #     This will define a symbol, F_USB, in all source code files equal to the
  32 #     input clock frequency (before any prescaling is performed) in Hz. This value may
  33 #     differ from F_CPU if prescaling is used on the latter, and is required as the
  34 #     raw input clock is fed directly to the PLL sections of the AVR for high speed
  35 #     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
  36 #     at the end, this will be done automatically to create a 32-bit value in your
  37 #     source code.
  38 #
  39 #     If no clock division is performed on the input clock inside the AVR (via the
  40 #     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
  41 F_USB = $(F_CPU)
  42
  43 # Interrupt driven control endpoint task(+60)
  44 OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
  45
  46
  47 # Boot Section Size in *bytes*
  48 #   Teensy halfKay   512
  49 #   Teensy++ halfKay 1024
  50 #   Atmel DFU loader 4096
  51 #   LUFA bootloader  4096
  52 #   USBaspLoader     2048
  53 OPT_DEFS += -DBOOTLOADER_SIZE=4096
  54
  55 # Build Options
  56 #   change to "no" to disable the options, or define them in the Makefile in
  57 #   the appropriate keymap folder that will get included automatically
  58 #
  59 BOOTMAGIC_ENABLE ?= no       # Virtual DIP switch configuration(+1000)
  60 MOUSEKEY_ENABLE ?= yes       # Mouse keys(+4700)
  61 EXTRAKEY_ENABLE ?= yes       # Audio control and System control(+450)
  62 CONSOLE_ENABLE ?= no         # Console for debug(+400)
  63 COMMAND_ENABLE ?= yes        # Commands for debug and configuration
  64 NKRO_ENABLE ?= no            # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
  65 BACKLIGHT_ENABLE ?= no      # Enable keyboard backlight functionality
  66 MIDI_ENABLE ?= no            # MIDI controls
  67 AUDIO_ENABLE ?= no           # Audio output on port C6
  68 UNICODE_ENABLE ?= no         # Unicode
  69 BLUETOOTH_ENABLE ?= no       # Enable Bluetooth with the Adafruit EZ-Key HID
  70 RGBLIGHT_ENABLE ?= no       # Enable WS2812 RGB underlight.  Do not enable this with audio at the same time.
  71 SUBPROJECT_rev1 ?= yes
  72 USE_I2C ?= yes
  73 # Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
  74 SLEEP_LED_ENABLE ?= no    # Breathing sleep LED during USB suspend
  75
  76 CUSTOM_MATRIX = yes