keyboards/bthlabs/geekpad/rules.mk

   1 # MCU name
   2 #MCU = at90usb1286
   3 MCU = atmega32u4
   4
   5 # Processor frequency.
   6 #     This will define a symbol, F_CPU, in all source code files equal to the
   7 #     processor frequency in Hz. You can then use this symbol in your source code to
   8 #     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
   9 #     automatically to create a 32-bit value in your source code.
  10 #
  11 #     This will be an integer division of F_USB below, as it is sourced by
  12 #     F_USB after it has run through any CPU prescalers. Note that this value
  13 #     does not *change* the processor frequency - it should merely be updated to
  14 #     reflect the processor speed set externally so that the code can use accurate
  15 #     software delays.
  16 F_CPU = 16000000
  17
  18
  19 #
  20 # LUFA specific
  21 #
  22 # Target architecture (see library "Board Types" documentation).
  23 ARCH = AVR8
  24
  25 # Input clock frequency.
  26 #     This will define a symbol, F_USB, in all source code files equal to the
  27 #     input clock frequency (before any prescaling is performed) in Hz. This value may
  28 #     differ from F_CPU if prescaling is used on the latter, and is required as the
  29 #     raw input clock is fed directly to the PLL sections of the AVR for high speed
  30 #     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
  31 #     at the end, this will be done automatically to create a 32-bit value in your
  32 #     source code.
  33 #
  34 #     If no clock division is performed on the input clock inside the AVR (via the
  35 #     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
  36 F_USB = $(F_CPU)
  37
  38 # Interrupt driven control endpoint task(+60)
  39 OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
  40
  41
  42 # Bootloader selection
  43 #   Teensy       halfkay
  44 #   Pro Micro    caterina
  45 #   Atmel DFU    atmel-dfu
  46 #   LUFA DFU     lufa-dfu
  47 #   QMK DFU      qmk-dfu
  48 #   atmega32a    bootloadHID
  49 BOOTLOADER = caterina
  50
  51
  52 # If you don't know the bootloader type, then you can specify the
  53 # Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
  54 #   Teensy halfKay      512
  55 #   Teensy++ halfKay    1024
  56 #   Atmel DFU loader    4096
  57 #   LUFA bootloader     4096
  58 #   USBaspLoader        2048
  59 # OPT_DEFS += -DBOOTLOADER_SIZE=4096
  60
  61
  62 # Build Options
  63 #   change yes to no to disable
  64 #
  65 BOOTMAGIC_ENABLE = no      # Virtual DIP switch configuration(+1000)
  66 MOUSEKEY_ENABLE = no       # Mouse keys(+4700)
  67 EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
  68 CONSOLE_ENABLE = no        # Console for debug(+400)
  69 COMMAND_ENABLE = no        # Commands for debug and configuration
  70 # Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
  71 SLEEP_LED_ENABLE = no       # Breathing sleep LED during USB suspend
  72 # if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
  73 NKRO_ENABLE = no            # USB Nkey Rollover
  74 BACKLIGHT_ENABLE = no       # Enable keyboard backlight functionality on B7 by default
  75 RGBLIGHT_ENABLE = no        # Enable keyboard RGB underglow
  76 MIDI_ENABLE = no            # MIDI support (+2400 to 4200, depending on config)
  77 UNICODE_ENABLE = no         # Unicode
  78 BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
  79 AUDIO_ENABLE = no           # Audio output on port C6
  80 FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
  81 HD44780_ENABLE = no             # Enable support for HD44780 based LCDs (+400)