8 # This will define a symbol, F_CPU, in all source code files equal to the
9 # processor frequency in Hz. You can then use this symbol in your source code to
10 # calculate timings. Do NOT tack on a 'UL' at the end, this will be done
11 # automatically to create a 32-bit value in your source code.
13 # This will be an integer division of F_USB below, as it is sourced by
14 # F_USB after it has run through any CPU prescalers. Note that this value
15 # does not *change* the processor frequency - it should merely be updated to
16 # reflect the processor speed set externally so that the code can use accurate
24 # Target architecture (see library "Board Types" documentation).
27 # Input clock frequency.
28 # This will define a symbol, F_USB, in all source code files equal to the
29 # input clock frequency (before any prescaling is performed) in Hz. This value may
30 # differ from F_CPU if prescaling is used on the latter, and is required as the
31 # raw input clock is fed directly to the PLL sections of the AVR for high speed
32 # clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
33 # at the end, this will be done automatically to create a 32-bit value in your
36 # If no clock division is performed on the input clock inside the AVR (via the
37 # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
40 # Interrupt driven control endpoint task(+60)
41 OPT_DEFS
+= -DINTERRUPT_CONTROL_ENDPOINT
44 # Bootloader selection
50 # atmega32a bootloadHID
51 BOOTLOADER
= atmel-dfu
54 # If you don't know the bootloader type, then you can specify the
55 # Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
57 # Teensy++ halfKay 1024
58 # Atmel DFU loader 4096
59 # LUFA bootloader 4096
61 # OPT_DEFS += -DBOOTLOADER_SIZE=4096
65 # change yes to no to disable
67 BOOTMAGIC_ENABLE
= no
# Virtual DIP switch configuration(+1000)
68 MOUSEKEY_ENABLE
= no
# Mouse keys(+4700)
69 EXTRAKEY_ENABLE
= yes
# Audio control and System control(+450)
70 CONSOLE_ENABLE
= no
# Console for debug(+400)
71 COMMAND_ENABLE
= no
# Commands for debug and configuration
72 # Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
73 SLEEP_LED_ENABLE
= no
# Breathing sleep LED during USB suspend
74 # if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
75 NKRO_ENABLE
= no
# USB Nkey Rollover
76 BACKLIGHT_ENABLE
= no
# Enable keyboard backlight functionality on B7 by default
77 RGBLIGHT_ENABLE
= no
# Enable keyboard RGB underglow
78 MIDI_ENABLE
= no
# MIDI support (+2400 to 4200, depending on config)
79 UNICODE_ENABLE
= no
# Unicode
80 BLUETOOTH_ENABLE
= no
# Enable Bluetooth with the Adafruit EZ-Key HID
81 AUDIO_ENABLE
= no
# Audio output on port C6
82 FAUXCLICKY_ENABLE
= no
# Use buzzer to emulate clicky switches
83 HD44780_ENABLE
= no
# Enable support for HD44780 based LCDs (+400)
86 CUSTOM_MATRIX
= yes
# Use custom matrix code
87 SPLIT_KEYBOARD
= yes
# Use shared split_common code