keyboards/atomic/Makefile

   1
   2
   3 # MCU name
   4 #MCU = at90usb1287
   5 MCU = atmega32u4
   6
   7 # Processor frequency.
   8 #     This will define a symbol, F_CPU, in all source code files equal to the
   9 #     processor frequency in Hz. You can then use this symbol in your source code to
  10 #     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
  11 #     automatically to create a 32-bit value in your source code.
  12 #
  13 #     This will be an integer division of F_USB below, as it is sourced by
  14 #     F_USB after it has run through any CPU prescalers. Note that this value
  15 #     does not *change* the processor frequency - it should merely be updated to
  16 #     reflect the processor speed set externally so that the code can use accurate
  17 #     software delays.
  18 F_CPU = 16000000
  19
  20 #
  21 # LUFA specific
  22 #
  23 # Target architecture (see library "Board Types" documentation).
  24 ARCH = AVR8
  25
  26 # Input clock frequency.
  27 #     This will define a symbol, F_USB, in all source code files equal to the
  28 #     input clock frequency (before any prescaling is performed) in Hz. This value may
  29 #     differ from F_CPU if prescaling is used on the latter, and is required as the
  30 #     raw input clock is fed directly to the PLL sections of the AVR for high speed
  31 #     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
  32 #     at the end, this will be done automatically to create a 32-bit value in your
  33 #     source code.
  34 #
  35 #     If no clock division is performed on the input clock inside the AVR (via the
  36 #     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
  37 F_USB = $(F_CPU)
  38
  39 # Interrupt driven control endpoint task(+60)
  40 OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
  41
  42
  43 # Boot Section Size in *bytes*
  44 #   Teensy halfKay   512
  45 #   Teensy++ halfKay 1024
  46 #   Atmel DFU loader 4096
  47 #   LUFA bootloader  4096
  48 #   USBaspLoader     2048
  49 OPT_DEFS += -DBOOTLOADER_SIZE=4096
  50
  51 # Build Options
  52 #   change to "no" to disable the options, or define them in the Makefile in
  53 #   the appropriate keymap folder that will get included automatically
  54 #
  55 BOOTMAGIC_ENABLE ?= no       # Virtual DIP switch configuration(+1000)
  56 MOUSEKEY_ENABLE ?= yes       # Mouse keys(+4700)
  57 EXTRAKEY_ENABLE ?= yes       # Audio control and System control(+450)
  58 CONSOLE_ENABLE ?= no         # Console for debug(+400)
  59 COMMAND_ENABLE ?= yes        # Commands for debug and configuration
  60 NKRO_ENABLE ?= no            # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
  61 BACKLIGHT_ENABLE ?= yes      # Enable keyboard backlight functionality
  62 MIDI_ENABLE ?= no            # MIDI controls
  63 AUDIO_ENABLE ?= no           # Audio output on port C6
  64 UNICODE_ENABLE ?= no         # Unicode
  65 BLUETOOTH_ENABLE ?= no       # Enable Bluetooth with the Adafruit EZ-Key HID
  66 RGBLIGHT_ENABLE ?= no        # Enable WS2812 RGB underlight.  Do not enable this with audio at the same time.
  67
  68 # Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
  69 SLEEP_LED_ENABLE ?= no    # Breathing sleep LED during USB suspend
  70
  71 ifndef QUANTUM_DIR
  72         include ../../Makefile
  73 endif