HCoop / jackhill / qmk / firmware.git / blame
| Commit | Line | Data |
|---|---|---|
| 87e6d013 G |
1 | # MCU name |
| 2 | #MCU = at90usb1287 | |
| 3 | MCU = atmega32u4 | |
| 4 | ||
| 5 | # Processor frequency. | |
| 6 | # This will define a symbol, F_CPU, in all source code files equal to the | |
| 7 | # processor frequency in Hz. You can then use this symbol in your source code to | |
| 8 | # calculate timings. Do NOT tack on a 'UL' at the end, this will be done | |
| 9 | # automatically to create a 32-bit value in your source code. | |
| 10 | # | |
| 11 | # This will be an integer division of F_USB below, as it is sourced by | |
| 12 | # F_USB after it has run through any CPU prescalers. Note that this value | |
| 13 | # does not *change* the processor frequency - it should merely be updated to | |
| 14 | # reflect the processor speed set externally so that the code can use accurate | |
| 15 | # software delays. | |
| 16 | F_CPU = 16000000 | |
| 17 | ||
| 18 | # | |
| 19 | # LUFA specific | |
| 20 | # | |
| 21 | # Target architecture (see library "Board Types" documentation). | |
| 22 | ARCH = AVR8 | |
| 23 | ||
| 24 | # Input clock frequency. | |
| 25 | # This will define a symbol, F_USB, in all source code files equal to the | |
| 26 | # input clock frequency (before any prescaling is performed) in Hz. This value may | |
| 27 | # differ from F_CPU if prescaling is used on the latter, and is required as the | |
| 28 | # raw input clock is fed directly to the PLL sections of the AVR for high speed | |
| 29 | # clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | |
| 30 | # at the end, this will be done automatically to create a 32-bit value in your | |
| 31 | # source code. | |
| 32 | # | |
| 33 | # If no clock division is performed on the input clock inside the AVR (via the | |
| 34 | # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | |
| 35 | F_USB = $(F_CPU) | |
| 36 | ||
| 37 | # Interrupt driven control endpoint task(+60) | |
| 38 | OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT | |
| 39 | ||
| 40 | ||
| 41 | # Boot Section Size in *bytes* | |
| 42 | # Teensy halfKay 512 | |
| 43 | # Teensy++ halfKay 1024 | |
| 44 | # Atmel DFU loader 4096 | |
| 45 | # LUFA bootloader 4096 | |
| 46 | # USBaspLoader 2048 | |
| 47 | BOOTLOADER = caterina | |
| 48 | ||
| 49 | # Build Options | |
| 50 | # change to "no" to disable the options, or define them in the Makefile in | |
| 51 | # the appropriate keymap folder that will get included automatically | |
| 52 | # | |
| 53 | BOOTMAGIC_ENABLE = lite # Virtual DIP switch configuration(+1000) | |
| 54 | MOUSEKEY_ENABLE = yes # Mouse keys(+4700) | |
| 55 | EXTRAKEY_ENABLE = yes # Audio control and System control(+450) | |
| 56 | CONSOLE_ENABLE = no # Console for debug(+400) | |
| 57 | COMMAND_ENABLE = no # Commands for debug and configuration | |
| 58 | NKRO_ENABLE = yes # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work | |
| 59 | BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality | |
| 60 | MIDI_ENABLE = no # MIDI controls | |
| 61 | AUDIO_ENABLE = no # Audio output on port C6 | |
| 62 | UNICODE_ENABLE = yes # Unicode | |
| 63 | BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID | |
| 64 | RGBLIGHT_ENABLE = yes # Enable WS2812 RGB underlight. | |
| 65 | IOS_DEVICE_ENABLE = no # connect to IOS Device | |
| 66 | ||
| 67 | ifeq ($(strip $(IOS_DEVICE_ENABLE )), yes) | |
| 68 | OPT_DEFS += -DIOS_DEVICE_ENABLE | |
| 69 | endif | |
| 70 | ||
| 71 | # Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE | |
| 72 | SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend | |
| 73 | ||
| 74 | LAYOUTS = ortho_4x10 |