doc/wilson-bom-ts.txt

   1 Exported bom for Wilson TS from wilson-bom.ods
   2 Please see the ODS file for details.
   3 ----------------------------------------------
   4
   5 Item                                    Quantity        Length / Notes
   6
   7 2020 Extrusions
   8 Vertical frame piece (sides)            2           400mm
   9 Horizontal frame piece (top and bottom) 2           320mm
  10 Y axis frame piece (TS only)            2           415mm
  11
  12 M8 Smooth Rods
  13 X-Axis                                  2           380mm
  14 Y-Axis                                  2           415mm
  15 Z-Axis                                  2           350mm
  16
  17 Threaded Rods
  18 M5 threaded rod for Z axis              2           325mm
  19
  20 Belts & Pulleys
  21 Y axis GT2 timing belt (w=6mm)          1           850mm
  22 X axis GT2 timing belt (w=6mm)          1           930mm
  23 GT2 pulley                              2           Want diameter 16-20mm
  24 Nuts & Bolts
  25 M5 x 10mm machine screw                 44
  26 M5 hex nut                               2
  27 M5 t slot nut                           44
  28 M4 x 20mm machine screw                  6
  29 M4 hex nut                               6
  30 M3 x 8mm machine screw                   1
  31 M3 x 10mm machine screw                 11
  32 M3 x 14mm machine screw                 18
  33 M3 x 30mm machine screw                  7
  34 M3 x 60mm machine screw                  2         50mm? if spring short enough
  35 M3 hex nut                             20?         This number is approximate
  36 M3 lock nut                              7
  37 M3 washer                              20?         This number is approximate
  38 M8 x 20mm smooth rod or grub screw       1
  39 M8 washers                               5         For alignment of hobbed bolt
  40 M8 locknut                               1         For extruder bolt
  41 Printed Parts – Required
  42 X end idler                              1
  43 X end motor                              1
  44 X carriage                               1
  45 Y end idler                              1
  46 Y end motor                              1
  47 Y belt holder                            1
  48 Y axis bearing holder                    4         for lm8uu bearings
  49 Z motor holder, left                     1
  50 Z motor holder, right                    1
  51 Z rod holder, left                       1
  52 Z rod holder, right                      1
  53 Z rear bracket                           2
  54 Z endstop holder                         1
  55 Frame brace                              4
  56 Idler bearing guide (pair)               2
  57 Extruder body / idler set                1
  58 Extruder big gear / small gear set       1
  59 Extruder fan duct                        1
  60 Belt guides                                  4         (two belt guides, one for each 624 bearing)
  61 Printed Parts – Recommended
  62 Electronics frame mount (for RAMPS)     1
  63 Filament spool support (two pieces)     1
  64 SMART display frame mount (two pieces)  1
  65 Everything Else
  66 NEMA17 Stepper motor    5
  67 MDF board (6mm thick)   1       230mm by 230mm
  68 MK2 Heat bed    1
  69 Glass bed       1       3mm borosilicate
  70 Controller (Mega/RAMPS, Rambo, etc)     1
  71 Endstop (limit) switch  3       6mm x 10mm x 20mm
  72 LM8UU Linear bearing    12
  73 608ZZ roller bearing    4
  74 624 roller bearing      2
  75 5mm to 5mm shaft couplers       2       Can also use vinyl tubing instead
  76 40mm x 40mm x 10mm fan  1       12V
  77 80mm x 80mm fan 1       For use with RAMPS frame mount
  78 Miniature zip ties      20      This number is approximate
  79 Extruder idler springs  2       High tension
  80 Bed leveling springs    4       Lower tension
  81 Power Supply    1       Size appropriately for heat bed and extruder
  82 Hobbed bolt     1       Recommend airwolf3d
  83 Hot end 1       Recommend Jhead
  84