// Josef Průša <josefprusa@me.com>
// Václav 'ax' Hůla <axtheb@gmail.com>
// http://www.reprap.org/wiki/Prusa_Mendel
-// http://github.com/prusajr/PrusaMendel
+// http://github.com/josefprusa/Prusa3
include <inc/metric.scad>;
include <inc/conf_bushing.scad>;
// Custom settings here, tailor to your supplies and print settings
-
// Extruder settings **********************************************************
// Don't forget to set your slicer's extruder settings to match the values you
// enter here.
// width will be 0.66 mm.
width_over_thickness = 2.2;
-
// Select your belt type ******************************************************
// T2.5
-belt_tooth_distance = 2.5;
-belt_tooth_ratio = 0.75;
+//belt_width = 6.5; //add 0.5 to actual width
+//belt_tooth_distance = 2.5;
+//belt_tooth_ratio = 0.75;
+//belt_thickness = 0.8;
// T5 (strongly discouraged)
-// belt_tooth_distance = 5;
-// belt_tooth_ratio = 0.75;
+//belt_width = 6.5;
+//belt_tooth_distance = 5;
+//belt_tooth_ratio = 0.75;
+//belt_thickness = 0.8;
// HTD3
-// belt_tooth_distance = 3;
-// belt_tooth_ratio = 0.75;
+//belt_width = 9.5;
+//belt_tooth_distance = 3;
+//belt_tooth_ratio = 0.75;
+//belt_thickness = 1.75;
// MXL
-// belt_tooth_distance = 2.032;
-// belt_tooth_ratio = 0.64;
-
-// GT2 there is bunch of GT2 belts with different tooth-to-tooth distance
-// adjust to your needs
-// belt_tooth_distance = 2;
-// belt_tooth_ratio = 0.5;
-
-// For T type belts you will probably want 0.8mm or so.
-belt_thickness = 1.75;
-
+//belt_width = 6.5;
+//belt_tooth_distance = 2.032;
+//belt_tooth_ratio = 0.64;
+//belt_thickness = i have no idea;
+
+// GT2
+// there is bunch of GT2 belts with different tooth-to-tooth distance
+// this one is most common in reprap world
+// adjust to your needs.
+belt_width = 6.5;
+belt_tooth_distance = 2;
+belt_tooth_ratio = 0.5;
+belt_thickness = 0.8;
// Choose bearing/bushing configuration ***************************************
// conf_b_* are in inc/conf_bushing.scad
// Select idler bearing size **************************************************
-// [outer_diameter, width, inner_diameter, uses_guide]
-
-// 608 [standard skate bearings] with bearing guide
-bearing_608 = [22, 7, 8, 1];
-// 608 bearings with fender washers. Not good at all, the belt brushes against the carriage
-bearing_608_washers = [22, 10, 8, 0];
-
-// one 625 with guides
-bearing_625 = [16, 5, 5, 1];
-// two 625 - for use without bearing guides.
-bearing_625_double = [16, 10, 5, 0];
+// bearing_* are in inc/conf_bushing.scad
-// those two here are really good:
-bearing_624_double = [13, 10, 4, 0];
-
-// this one has roughly same diameter as pulley, makes belt parallel so its prettier
-bearing_623_double = [10, 8, 3, 0];
-
-idler_bearing = bearing_624_double;
+idler_bearing = bearing_623;
// Select carriage lenght ******************************************************
// 30 for single carriage extruder (two holes with centers 30mm apart)
use_fillets = 1;
-// set to 0 for single plate (affects z axis and screws that attach RP parts to frame)
-i_am_box = 1;
+// set to type of frame used (affects z axis and screws that attach RP parts to frame)
+frame_type = frame_single;
// if you do your own plate and can move bottom Z screws 5mm up set this to 0 to
// get stronger motor mount. Only for i_am_box = 0
// is in the center of the plank.
// Use 12 for single plate
-// or 20 if you want to use the Y lm8uu holders
+// or 20 if you want to use the Y lm8uu holders
// (extras/bearing-holder-single-plate-y)
+// For an aluminum extrusion frame, set this to your extrusion diameter
board_thickness = 12;
// Segments of small holes. some poeple claim that a low value makes them easier to print.
small_hole_segments=7;
-
-// END of custom settings *****************************************************
-
-
-// You are not supposed to change this
-board_to_xz_distance = 26;
-xaxis_rod_distance = 45;
-
-//calculated from settings
-single_wall_width = width_over_thickness * layer_height;
-
-idler_width = (idler_bearing[1] > 7 ? idler_bearing[1] : 7) + 2.5 * idler_bearing[3] ;
-
-//deltas are used to enlarge parts for bigger bearings
-xy_delta = ((bushing_xy[1] <= 7.7) ? 0 : bushing_xy[1] - 7.7) * 0.9;
-z_delta = (bushing_z[1] <= 7.7) ? 0 : bushing_z[1] - 7.7;
-
-// CHANGE ONLY THE STUFF YOU KNOW
-// IT WILL REPLACE DEFAULT SETTING
-
-// RODS
-
-// threaded_rod_diameter = 0;
-// threaded_rod_diameter_horizontal = 0;
-// smooth_bar_diameter = 0;
-// smooth_bar_diameter_horizontal = 0;
-
-// Nuts and bolts
-
-// m8_diameter = 0;
-// m8_nut_diameter = 0;
-
-// m4_diameter = 0;
-// m4_nut_diameter = 0;
-
-// m3_diameter = 0;
-// m3_nut_diameter = 0;
-
-// Bushing holder
-
-// bushing_core_diameter = smooth_bar_diameter;
-// bushing_material_thickness = 0;
-
-///counted stuff
-m3_nut_diameter_bigger = ((m3_nut_diameter / 2) / cos (180 / 6))*2;
-
// functions
-include <inc/functions.scad>
-
-// These constants define the geometry of the complete-printer.scad
+include <inc/functions.scad>;
+include <inc/settings.scad>;
-//x_smooth_rod_length=325;
-//y_smooth_rod_length=405;
-//z_smooth_rod_length=235;
+// These constants define the geometry of the doc/complete-printer.scad
bed_x_size=225;
bed_y_size=225;
+x_smooth_rod_length=380+board_thickness*2;
+y_smooth_rod_length=400;
+z_smooth_rod_length=320;
-x_smooth_rod_length=460+board_thickness*2; // 492 for 16mm thickness; 484 for 12mm thickness
-y_smooth_rod_length=470;
-z_smooth_rod_length=405;
+// shift smooth rod and leadscrew
+zaxis_delta_x = 0;
+zaxis_delta_y = 0;
\ No newline at end of file
HCoop / clinton / prusa3.git / blobdiff