-#leveling-strategy.three-point-leveling.probe_offsets 0,0,0 # the probe offsets from nozzle, must be x,y,z, default is no offset# Robot module configurations : general handling of movement G-codes and slicing into moves
+# Robot module configurations : general handling of movement G-codes and slicing into moves
default_feed_rate 4000 # Default rate ( mm/minute ) for G1/G2/G3 moves
default_seek_rate 4000 # Default rate ( mm/minute ) for G0 moves
mm_per_arc_segment 0.5 # Arcs are cut into segments ( lines ), this is the length for these segments. Smaller values mean more resolution, higher values mean faster computation
-mm_per_line_segment 5 # Lines can be cut into segments ( not usefull with cartesian coordinates robots ).
+#mm_per_line_segment 5 # Lines can be cut into segments ( not usefull with cartesian coordinates robots ).
# Arm solution configuration : Cartesian robot. Translates mm positions into stepper positions
alpha_steps_per_mm 80 # Steps per mm for alpha stepper
# Stepper module configuration
microseconds_per_step_pulse 1 # Duration of step pulses to stepper drivers, in microseconds
-base_stepping_frequency 100000 # Base frequency for stepping, higher gives smoother movement
+base_stepping_frequency 100000 # Base frequency for stepping
# Stepper module pins ( ports, and pin numbers, appending "!" to the number will invert a pin )
alpha_step_pin 2.1 # Pin for alpha stepper step signal
# Serial communications configuration ( baud rate default to 9600 if undefined )
uart0.baud_rate 115200 # Baud rate for the default hardware serial port
second_usb_serial_enable false # This enables a second usb serial port (to have both pronterface and a terminal connected)
+
#msd_disable false # disable the MSD (USB SDCARD) when set to true
+#leds_disable true # disable using leds after config loaded
+#dfu_enable false # for linux developers, set to true to enable DFU
+#watchdog_timeout 10 # watchdog timeout in seconds, default is 10, set to 0 to disable the watchdog
# Extruder module configuration
extruder_module_enable true # Whether to activate the extruder module at all. All configuration is ignored if false
delta_current 1.0 # Extruder stepper motor current
# Laser module configuration
-laser_module_enable false # Whether to activate the laser module at all. All configuration is ignored if false.
-#laser_module_pin 2.7 # this pin will be PWMed to control the laser
-#laser_module_max_power 0.8 # this is the maximum duty cycle that will be applied to the laser
-#laser_module_tickle_power 0.0 # this duty cycle will be used for travel moves to keep the laser active without actually burning
+laser_module_enable false # Whether to activate the laser module at all. All configuration is
+ # ignored if false.
+#laser_module_pin 2.5 # this pin will be PWMed to control the laser. Only P2.0 - P2.5, P1.18, P1.20, P1.21, P1.23, P1.24, P1.26, P3.25, P3.26
+ # can be used since laser requires hardware PWM
+#laser_module_maximum_power 1.0 # this is the maximum duty cycle that will be applied to the laser
+#laser_module_minimum_power 0.0 # This is a value just below the minimum duty cycle that keeps the laser
+ # active without actually burning.
+#laser_module_default_power 0.8 # This is the default laser power that will be used for cuts if a power has not been specified. The value is a scale between
+ # the maximum and minimum power levels specified above
+#laser_module_pwm_period 20 # this sets the pwm frequency as the period in microseconds
# Hotend temperature control configuration
temperature_control.hotend.enable true # Whether to activate this ( "hotend" ) module at all. All configuration is ignored if false.
temperature_control.hotend.set_m_code 104 #
temperature_control.hotend.set_and_wait_m_code 109 #
temperature_control.hotend.designator T #
+#temperature_control.hotend.max_temp 300 # Set maximum temperature - Will prevent heating above 300 by default
+#temperature_control.hotend.min_temp 0 # Set minimum temperature - Will prevent heating below 0 by default
temperature_control.hotend.p_factor 13.7 #
temperature_control.hotend.i_factor 0.097 #
#temperatureswitch.hotend.heatup_poll 15 # poll heatup at 15 sec intervals
#temperatureswitch.hotend.cooldown_poll 60 # poll cooldown at 60 sec intervals
+# filament out detector
+#filament_detector.enable true #
+#filament_detector.encoder_pin 0.26 # must be interrupt enabled pin (0.26, 0.27, 0.28)
+#filament_detector.seconds_per_check 2 # may need to be longer
+#filament_detector.pulses_per_mm 1 .0 # will need to be tuned
+#filament_detector.bulge_pin 0.27 # optional bulge detector switch and/or manual suspend
# Switch module for spindle control
#switch.spindle.enable false #
#alpha_limit_enable false # set to true to enable X min and max limit switches
#beta_limit_enable false # set to true to enable Y min and max limit switches
#gamma_limit_enable false # set to true to enable Z min and max limit switches
+#move_to_origin_after_home false # move XY to 0,0 after homing
#probe endstop
#probe_pin 1.29 # optional pin for probe
#leveling-strategy.three-point-leveling.save_plane false # set to true to allow the bed plane to be saved with M500 default is false
-# Pause button
-pause_button_enable true #
+# kill button (used to be called pause) maybe assigned to a different pin, set to the onboard pin by default
+kill_button_enable true # set to true to enable a kill button
+kill_button_pin 2.12 # kill button pin. default is same as pause button 2.12 (2.11 is another good choice)
# Panel See http://smoothieware.org/panel
panel.enable false # set to true to enable the panel code
currentcontrol_module_enable true #
digipot_max_current 2.4 # max current
digipot_factor 106.0 # factor for converting current to digipot value
-
-return_error_on_unhandled_gcode false #
-
-
HCoop / clinton / Smoothieware.git / blobdiff