#include <fastmath.h>
#include <string>
#include <algorithm>
-using std::string;
#define default_seek_rate_checksum CHECKSUM("default_seek_rate")
#define default_feed_rate_checksum CHECKSUM("default_feed_rate")
pins[i].from_string(THEKERNEL->config->value(checksums[a][i])->by_default("nc")->as_string())->as_output();
}
- if(!pins[0].connected() || !pins[1].connected() || !pins[2].connected()) {
- if(a <= Z_AXIS) THEKERNEL->streams->printf("FATAL: motor %d is not defined in config\n", 'X'+a);
+ if(!pins[0].connected() || !pins[1].connected()) { // step and dir must be defined, but enable is optional
+ if(a <= Z_AXIS) {
+ THEKERNEL->streams->printf("FATAL: motor %c is not defined in config\n", 'X'+a);
+ n_motors= a; // we only have this number of motors
+ return;
+ }
break; // if any pin is not defined then the axis is not defined (and axis need to be defined in contiguous order)
}
if(n != a) {
// this is a fatal error
THEKERNEL->streams->printf("FATAL: motor %d does not match index %d\n", n, a);
- __debugbreak();
+ return;
}
actuators[a]->change_steps_per_mm(THEKERNEL->config->value(checksums[a][3])->by_default(a == 2 ? 2560.0F : 80.0F)->as_number());
arm_solution->actuator_to_cartesian(current_position, pos);
}
-int Robot::print_position(uint8_t subcode, char *buf, size_t bufsize) const
+void Robot::print_position(uint8_t subcode, std::string& res, bool ignore_extruders) const
{
// M114.1 is a new way to do this (similar to how GRBL does it).
// it returns the realtime position based on the current step position of the actuators.
// this does require a FK to get a machine position from the actuator position
// and then invert all the transforms to get a workspace position from machine position
// M114 just does it the old way uses machine_position and does inverse transforms to get the requested position
- int n = 0;
+ uint32_t n = 0;
+ char buf[64];
if(subcode == 0) { // M114 print WCS
wcs_t pos= mcs2wcs(machine_position);
- n = snprintf(buf, bufsize, "C: X:%1.4f Y:%1.4f Z:%1.4f", from_millimeters(std::get<X_AXIS>(pos)), from_millimeters(std::get<Y_AXIS>(pos)), from_millimeters(std::get<Z_AXIS>(pos)));
+ n = snprintf(buf, sizeof(buf), "C: X:%1.4f Y:%1.4f Z:%1.4f", from_millimeters(std::get<X_AXIS>(pos)), from_millimeters(std::get<Y_AXIS>(pos)), from_millimeters(std::get<Z_AXIS>(pos)));
} else if(subcode == 4) {
// M114.4 print last milestone
- n = snprintf(buf, bufsize, "MP: X:%1.4f Y:%1.4f Z:%1.4f", machine_position[X_AXIS], machine_position[Y_AXIS], machine_position[Z_AXIS]);
+ n = snprintf(buf, sizeof(buf), "MP: X:%1.4f Y:%1.4f Z:%1.4f", machine_position[X_AXIS], machine_position[Y_AXIS], machine_position[Z_AXIS]);
} else if(subcode == 5) {
// M114.5 print last machine position (which should be the same as M114.1 if axis are not moving and no level compensation)
// will differ from LMS by the compensation at the current position otherwise
- n = snprintf(buf, bufsize, "CMP: X:%1.4f Y:%1.4f Z:%1.4f", compensated_machine_position[X_AXIS], compensated_machine_position[Y_AXIS], compensated_machine_position[Z_AXIS]);
+ n = snprintf(buf, sizeof(buf), "CMP: X:%1.4f Y:%1.4f Z:%1.4f", compensated_machine_position[X_AXIS], compensated_machine_position[Y_AXIS], compensated_machine_position[Z_AXIS]);
} else {
// get real time positions
if(subcode == 1) { // M114.1 print realtime WCS
wcs_t pos= mcs2wcs(mpos);
- n = snprintf(buf, bufsize, "WCS: X:%1.4f Y:%1.4f Z:%1.4f", from_millimeters(std::get<X_AXIS>(pos)), from_millimeters(std::get<Y_AXIS>(pos)), from_millimeters(std::get<Z_AXIS>(pos)));
+ n = snprintf(buf, sizeof(buf), "WCS: X:%1.4f Y:%1.4f Z:%1.4f", from_millimeters(std::get<X_AXIS>(pos)), from_millimeters(std::get<Y_AXIS>(pos)), from_millimeters(std::get<Z_AXIS>(pos)));
} else if(subcode == 2) { // M114.2 print realtime Machine coordinate system
- n = snprintf(buf, bufsize, "MCS: X:%1.4f Y:%1.4f Z:%1.4f", mpos[X_AXIS], mpos[Y_AXIS], mpos[Z_AXIS]);
+ n = snprintf(buf, sizeof(buf), "MCS: X:%1.4f Y:%1.4f Z:%1.4f", mpos[X_AXIS], mpos[Y_AXIS], mpos[Z_AXIS]);
} else if(subcode == 3) { // M114.3 print realtime actuator position
// get real time current actuator position in mm
actuators[Y_AXIS]->get_current_position(),
actuators[Z_AXIS]->get_current_position()
};
- n = snprintf(buf, bufsize, "APOS: X:%1.4f Y:%1.4f Z:%1.4f", current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS]);
+ n = snprintf(buf, sizeof(buf), "APOS: X:%1.4f Y:%1.4f Z:%1.4f", current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS]);
}
}
+ if(n > sizeof(buf)) n= sizeof(buf);
+ res.append(buf, n);
+
#if MAX_ROBOT_ACTUATORS > 3
// deal with the ABC axis
for (int i = A_AXIS; i < n_motors; ++i) {
- if(actuators[i]->is_extruder()) continue; // don't show an extruder as that will be E
+ n= 0;
+ if(ignore_extruders && actuators[i]->is_extruder()) continue; // don't show an extruder as that will be E
if(subcode == 4) { // M114.4 print last milestone
- n += snprintf(&buf[n], bufsize-n, " %c:%1.4f", 'A'+i-A_AXIS, machine_position[i]);
+ n= snprintf(buf, sizeof(buf), " %c:%1.4f", 'A'+i-A_AXIS, machine_position[i]);
}else if(subcode == 2 || subcode == 3) { // M114.2/M114.3 print actuator position which is the same as machine position for ABC
// current actuator position
- n += snprintf(&buf[n], bufsize-n, " %c:%1.4f", 'A'+i-A_AXIS, actuators[i]->get_current_position());
+ n= snprintf(buf, sizeof(buf), " %c:%1.4f", 'A'+i-A_AXIS, actuators[i]->get_current_position());
}
+ if(n > sizeof(buf)) n= sizeof(buf);
+ if(n > 0) res.append(buf, n);
}
#endif
-
- return n;
}
// converts current last milestone (machine position without compensation transform) to work coordinate system (inverse transform)
void Robot::check_max_actuator_speeds()
{
for (size_t i = 0; i < n_motors; i++) {
+ if(actuators[i]->is_extruder()) continue; //extruders are not included in this check
+
float step_freq = actuators[i]->get_max_rate() * actuators[i]->get_steps_per_mm();
if (step_freq > THEKERNEL->base_stepping_frequency) {
actuators[i]->set_max_rate(floorf(THEKERNEL->base_stepping_frequency / actuators[i]->get_steps_per_mm()));
case 1: motion_mode = LINEAR; break;
case 2: motion_mode = CW_ARC; break;
case 3: motion_mode = CCW_ARC; break;
- case 4: { // G4 pause
+ case 4: { // G4 Dwell
uint32_t delay_ms = 0;
if (gcode->has_letter('P')) {
- delay_ms = gcode->get_int('P');
+ if(THEKERNEL->is_grbl_mode()) {
+ // in grbl mode (and linuxcnc) P is decimal seconds
+ float f= gcode->get_value('P');
+ delay_ms= f * 1000.0F;
+
+ }else{
+ // in reprap P is milliseconds, they always have to be different!
+ delay_ms = gcode->get_int('P');
+ }
}
if (gcode->has_letter('S')) {
delay_ms += gcode->get_int('S') * 1000;
case 92: // M92 - set steps per mm
for (int i = 0; i < n_motors; ++i) {
+ if(actuators[i]->is_extruder()) continue; //extruders handle this themselves
char axis= (i <= Z_AXIS ? 'X'+i : 'A'+(i-A_AXIS));
if(gcode->has_letter(axis)) {
actuators[i]->change_steps_per_mm(this->to_millimeters(gcode->get_value(axis)));
return;
case 114:{
- char buf[64];
- int n= print_position(gcode->subcode, buf, sizeof buf);
- if(n > 0) gcode->txt_after_ok.append(buf, n);
+ std::string buf;
+ print_position(gcode->subcode, buf, true); // ignore extruders as they will print E themselves
+ gcode->txt_after_ok.append(buf);
return;
}
}
if(gcode->subcode == 1) {
for (size_t i = A_AXIS; i < n_motors; i++) {
+ if(actuators[i]->is_extruder()) continue; //extruders handle this themselves
gcode->stream->printf(" %c: %g ", 'A' + i - A_AXIS, actuators[i]->get_max_rate());
}
}
}
}else{
- // already in machine coordinates, we do not add tool offset for that
+ // already in machine coordinates, we do not add wcs or tool offset for that
for(int i= X_AXIS; i <= Z_AXIS; ++i) {
if(!isnan(param[i])) target[i] = param[i];
}
}
bool move= false;
- float sos= 0; // sum of squares for just XYZ
+ float sos= 0; // sum of squares for just primary axis (XYZ usually)
// find distance moved by each axis, use transformed target from the current compensated machine position
for (size_t i = 0; i < n_motors; i++) {
if(deltas[i] == 0) continue;
// at least one non zero delta
move = true;
- if(i <= Z_AXIS) {
+ if(i < N_PRIMARY_AXIS) {
sos += powf(deltas[i], 2);
}
}
if(!move) return false;
// see if this is a primary axis move or not
- bool auxilliary_move= deltas[X_AXIS] == 0 && deltas[Y_AXIS] == 0 && deltas[Z_AXIS] == 0;
+ bool auxilliary_move= true;
+ for (int i = 0; i < N_PRIMARY_AXIS; ++i) {
+ if(deltas[i] != 0) {
+ auxilliary_move= false;
+ break;
+ }
+ }
// total movement, use XYZ if a primary axis otherwise we calculate distance for E after scaling to mm
float distance= auxilliary_move ? 0 : sqrtf(sos);
if(!auxilliary_move) {
- for (size_t i = X_AXIS; i <= Z_AXIS; i++) {
+ for (size_t i = X_AXIS; i < N_PRIMARY_AXIS; i++) {
// find distance unit vector for primary axis only
unit_vec[i] = deltas[i] / distance;
// Do not move faster than the configured cartesian limits for XYZ
- if ( max_speeds[i] > 0 ) {
+ if ( i <= Z_AXIS && max_speeds[i] > 0 ) {
float axis_speed = fabsf(unit_vec[i] * rate_mm_s);
if (axis_speed > max_speeds[i])
}
if(auxilliary_move) {
// for E only moves we need to use the scaled E to calculate the distance
- sos += pow(actuator_pos[i] - actuators[i]->get_last_milestone(), 2);
+ sos += powf(actuator_pos[i] - actuators[i]->get_last_milestone(), 2);
}
}
if(auxilliary_move) {
// adjust acceleration to lowest found, for now just primary axis unless it is an auxiliary move
// TODO we may need to do all of them, check E won't limit XYZ.. it does on long E moves, but not checking it could exceed the E acceleration.
- if(auxilliary_move || actuator <= Z_AXIS) {
+ if(auxilliary_move || actuator < N_PRIMARY_AXIS) {
float ma = actuators[actuator]->get_acceleration(); // in mm/sec²
if(!isnan(ma)) { // if axis does not have acceleration set then it uses the default_acceleration
float ca = fabsf((d/distance) * acceleration);
}
}
+ // if we are in feed hold wait here until it is released, this means that even segemnted lines will pause
+ while(THEKERNEL->get_feed_hold()) {
+ THEKERNEL->call_event(ON_IDLE, this);
+ // if we also got a HALT then break out of this
+ if(THEKERNEL->is_halted()) return false;
+ }
+
// Append the block to the planner
// NOTE that distance here should be either the distance travelled by the XYZ axis, or the E mm travel if a solo E move
+ // NOTE this call will bock until there is room in the block queue, on_idle will continue to be called
if(THEKERNEL->planner->append_block( actuator_pos, n_motors, rate_mm_s, distance, auxilliary_move ? nullptr : unit_vec, acceleration, s_value, is_g123)) {
// this is the new compensated machine position
memcpy(this->compensated_machine_position, transformed_target, n_motors*sizeof(float));
// We always add another point after this loop so we stop at segments-1, ie i < segments
for (int i = 1; i < segments; i++) {
if(THEKERNEL->is_halted()) return false; // don't queue any more segments
- for (int i = 0; i < n_motors; i++)
- segment_end[i] += segment_delta[i];
+ for (int j = 0; j < n_motors; j++)
+ segment_end[j] += segment_delta[j];
// Append the end of this segment to the queue
+ // this can block waiting for free block queue or if in feed hold
bool b= this->append_milestone(segment_end, rate_mm_s);
moved= moved || b;
}
// Patch from GRBL Firmware - Christoph Baumann 04072015
// CCW angle between position and target from circle center. Only one atan2() trig computation required.
float angular_travel = atan2f(r_axis0 * rt_axis1 - r_axis1 * rt_axis0, r_axis0 * rt_axis0 + r_axis1 * rt_axis1);
+ if (plane_axis_2 == Y_AXIS) { is_clockwise = !is_clockwise; } //Math for XZ plane is revere of other 2 planes
if (is_clockwise) { // Correct atan2 output per direction
if (angular_travel >= -ARC_ANGULAR_TRAVEL_EPSILON) { angular_travel -= (2 * PI); }
} else {
float sin_T = theta_per_segment;
// TODO we need to handle the ABC axis here by segmenting them
- float arc_target[3];
+ float arc_target[n_motors];
float sin_Ti;
float cos_Ti;
float r_axisi;
uint16_t i;
int8_t count = 0;
+ // init array for all axis
+ memcpy(arc_target, machine_position, n_motors*sizeof(float));
+
// Initialize the linear axis
arc_target[this->plane_axis_2] = this->machine_position[this->plane_axis_2];
HCoop / clinton / Smoothieware.git / blobdiff