Merge remote-tracking branch 'upstream/edge' into hack/interim-feed-hold

[clinton/Smoothieware.git] / ConfigSamples / AzteegX5Mini / config

diff --git a/ConfigSamples/AzteegX5Mini/config b/ConfigSamples/AzteegX5Mini/config
index c8049a0..d981f99 100755 (executable)
--- a/ConfigSamples/AzteegX5Mini/config
+++ b/ConfigSamples/AzteegX5Mini/config
@@ -16,7 +16,6 @@ gamma_steps_per_mm                           1637.7953        # Steps per mm for
 planner_queue_size                           32               # DO NOT CHANGE THIS UNLESS YOU KNOW EXACTLY WHAT YOUR ARE DOING
 acceleration                                 3000             # Acceleration in mm/second/second.
 #z_acceleration                              500              # Acceleration for Z only moves in mm/s^2, 0 disables it, disabled by default. DO NOT SET ON A DELTA
-acceleration_ticks_per_second                1000             # Number of times per second the speed is updated
 junction_deviation                           0.05             # Similar to the old "max_jerk", in millimeters, see : https://github.com/grbl/grbl/blob/master/planner.c#L409
                                                               # and https://github.com/grbl/grbl/wiki/Configuring-Grbl-v0.8 . Lower values mean being more careful, higher values means being faster and have more jerk
 
@@ -55,16 +54,30 @@ second_usb_serial_enable                     false            # This enables a s
 #dfu_enable                                  false            # for linux developers, set to true to enable DFU
 #watchdog_timeout                            10               # watchdog timeout in seconds, default is 10, set to 0 to disable the watchdog
 
-# Extruder module configuration
-extruder_module_enable                       true             # Whether to activate the extruder module at all. All configuration is ignored if false
-extruder_steps_per_mm                        140              # Steps per mm for extruder stepper
-extruder_default_feed_rate                   600              # Default rate ( mm/minute ) for moves where only the extruder moves
-extruder_acceleration                        500              # Acceleration in mm/sec^2, only used for retracts
-extruder_max_speed                           1000             # mm/sec NOTE only used for retracts
+## Extruder module configuration
+extruder.hotend.enable                          true             # Whether to activate the extruder module at all. All configuration is ignored if false
+extruder.hotend.steps_per_mm                    140              # Steps per mm for extruder stepper
+extruder.hotend.default_feed_rate               600              # Default rate ( mm/minute ) for moves where only the extruder moves
+extruder.hotend.acceleration                    500              # Acceleration for the stepper motor mm/sec²
+extruder.hotend.max_speed                       50               # mm/s
+
+extruder.hotend.step_pin                        2.0              # Pin for extruder step signal
+extruder.hotend.dir_pin                         0.5             # Pin for extruder dir signal
+extruder.hotend.en_pin                          0.4             # Pin for extruder enable signal
+
+# extruder offset
+#extruder.hotend.x_offset                        0                # x offset from origin in mm
+#extruder.hotend.y_offset                        0                # y offset from origin in mm
+#extruder.hotend.z_offset                        0                # z offset from origin in mm
+
+# firmware retract settings when using G10/G11, these are the defaults if not defined, must be defined for each extruder if not using the defaults
+#extruder.hotend.retract_length                  3               # retract length in mm
+#extruder.hotend.retract_feedrate                45              # retract feedrate in mm/sec
+#extruder.hotend.retract_recover_length          0               # additional length for recover
+#extruder.hotend.retract_recover_feedrate        8               # recover feedrate in mm/sec (should be less than retract feedrate)
+#extruder.hotend.retract_zlift_length            0               # zlift on retract in mm, 0 disables
+#extruder.hotend.retract_zlift_feedrate          6000            # zlift feedrate in mm/min (Note mm/min NOT mm/sec)
 
-extruder_step_pin                            2.0              # Pin for extruder step signal
-extruder_dir_pin                             0.5              # Pin for extruder dir signal
-extruder_en_pin                              0.4              # Pin for extruder enable signal
 delta_current                                1.0              # Extruder stepper motor current
 
 # Laser module configuration
@@ -218,7 +231,7 @@ panel.a0_pin                                 2.6               # st7565 needs an
 panel.buzz_pin                               0.25              # pin for buzzer on EXP2
 panel.red_led_pin                            2.8               # pin for red led on viki2 on EXP1
 panel.blue_led_pin                           4.29              # pin for blue led on viki2 on EXP1
-panel.external_sd                            true              # set to true if there is an extrernal sdcard on the panel
+panel.external_sd                            false             # set to true to use external sd WARNING not supported.
 panel.external_sd.spi_channel                0                 # set spi channel the sdcard is on
 panel.external_sd.spi_cs_pin                 1.23              # set spi chip select for the sdcard
 panel.external_sd.sdcd_pin                   1.31!^            # sd detect signal (set to nc if no sdcard detect)