time to save again

[clinton/Smoothieware.git] / config-smoothieboard-copy_me_to_sd_card_and_rename_as_"config"

diff --git a/config-smoothieboard-copy_me_to_sd_card_and_rename_as_"config" b/config-smoothieboard-copy_me_to_sd_card_and_rename_as_"config"
index 01f4b16..8e00a9e 100644 (file)
--- a/config-smoothieboard-copy_me_to_sd_card_and_rename_as_"config"
+++ b/config-smoothieboard-copy_me_to_sd_card_and_rename_as_"config"
@@ -3,7 +3,6 @@ default_feed_rate                            4000             # Default rate ( m
 default_seek_rate                            4000             # Default rate ( mm/minute ) for G0 moves
 mm_per_arc_segment                           0.5              # Arcs are cut into segments ( lines ), this is the length for these segments.  Smaller values mean more resolution, higher values mean faster computation
 mm_per_line_segment                          5                # Lines can be cut into segments ( not usefull with cartesian coordinates robots ).
-z_axis_max_speed                             200              # Max allowable speed for this axis
 
 # Arm solution configuration : Cartesian robot. Translates mm positions into stepper positions
 alpha_steps_per_mm                           80               # Steps per mm for alpha stepper
@@ -12,30 +11,33 @@ gamma_steps_per_mm                           1600             # Steps per mm for
 
 # Planner module configuration : Look-ahead and acceleration configuration
 planner_queue_size                           64               # Size of the planning queue, must be a power of 2. 128 seems to be the maximum.
-acceleration                                 4000             # Acceleration in mm/second/second.
+acceleration                                 3000             # Acceleration in mm/second/second.
 acceleration_ticks_per_second                1000             # Number of times per second the speed is updated
 max_jerk                                     200              # Max instant cornering speed change. Higher means jerkier/faster, lower means smoother/slower.
 
 # Stepper module configuration
 microseconds_per_step_pulse                  1                # Duration of step pulses to stepper drivers, in microseconds
 minimum_steps_per_minute                     1200             # Never step slower than this
-base_stepping_frequency                      70000            # Base frequency for stepping, higher gives smoother movement
+base_stepping_frequency                      100000           # Base frequency for stepping, higher gives smoother movement
 
 # Stepper module pins ( ports, and pin numbers, appending "!" to the number will invert a pin )
 alpha_step_pin                               2.0              # Pin for alpha stepper step signal
 alpha_dir_pin                                0.5              # Pin for alpha stepper direction
 alpha_en_pin                                 0.4              # Pin for alpha enable pin
-alpha_current                                1.0              # X stepper motor current
+alpha_current                                1.5              # X stepper motor current
+x_axis_max_speed                             30000            # mm/min
 
 beta_step_pin                                2.1              # Pin for beta stepper step signal
 beta_dir_pin                                 0.11             # Pin for beta stepper direction
 beta_en_pin                                  0.10             # Pin for beta enable
-beta_current                                 1.0              # Y stepper motor current
+beta_current                                 1.5              # Y stepper motor current
+y_axis_max_speed                             30000            # mm/min
 
 gamma_step_pin                               2.2              # Pin for gamma stepper step signal
 gamma_dir_pin                                0.20             # Pin for gamma stepper direction
 gamma_en_pin                                 0.19             # Pin for gamma enable
-gamma_current                                1.0              # Z stepper motor current
+gamma_current                                1.5              # Z stepper motor current
+z_axis_max_speed                             300              # mm/min
 
 # Serial communications configuration ( baud rate default to 9600 if undefined )
 uart0.baud_rate                              115200           # Baud rate for the default serial port
@@ -45,11 +47,12 @@ extruder_module_enable                       true             # Whether to activ
 extruder_steps_per_mm                        140              # Steps per mm for extruder stepper
 extruder_default_feed_rate                   600              # Default rate ( mm/minute ) for moves where only the extruder moves
 extruder_acceleration                        50               # Acceleration for the stepper motor, as of 0.6, arbitrary ratio
+extruder_max_speed                           1000             # mm^3/s
 
 extruder_step_pin                            2.3              # Pin for extruder step signal
 extruder_dir_pin                             0.22             # Pin for extruder dir signal
 extruder_en_pin                              0.21             # Pin for extruder enable signal
-delta_current                                1.0              # Extruder stepper motor current
+delta_current                                1.5              # Extruder stepper motor current
 
 # Laser module configuration
 laser_module_enable                          false            # Whether to activate the laser module at all. All configuration is ignored if false.
@@ -57,7 +60,7 @@ laser_module_enable                          false            # Whether to activ
 # Hotend temperature control configuration
 temperature_control.hotend.enable            true             # Whether to activate this ( "hotend" ) module at all. All configuration is ignored if false.
 temperature_control.hotend.thermistor_pin    0.23             # Pin for the thermistor to read
-temperature_control.hotend.heater_pin        2.5              # Pin that controls the heater
+temperature_control.hotend.heater_pin        2.7              # Pin that controls the heater
 temperature_control.hotend.thermistor        EPCOS100K        # see src/modules/tools/temperaturecontrol/TemperatureControl.cpp:64 for a list of valid thermistor names
 temperature_control.hotend.set_m_code        104              #
 temperature_control.hotend.set_and_wait_m_code 109            #
@@ -65,7 +68,7 @@ temperature_control.hotend.designator        T                #
 
 temperature_control.bed.enable               true             #
 temperature_control.bed.thermistor_pin       0.24             #
-temperature_control.bed.heater_pin           2.7              #
+temperature_control.bed.heater_pin           2.5              #
 temperature_control.bed.thermistor           Honeywell100K    # see src/modules/tools/temperaturecontrol/TemperatureControl.cpp:64 for a list of valid thermistor names
 temperature_control.bed.set_m_code           140              #
 temperature_control.bed.set_and_wait_m_code  190              #