+++ /dev/null
-// PRUSA iteration3
-// Configuration file
-// GNU GPL v3
-// Josef Průša <josefprusa@me.com>
-// Václav 'ax' Hůla <axtheb@gmail.com>
-// http://www.reprap.org/wiki/Prusa_Mendel
-// http://github.com/prusajr/PrusaMendel
-
-// This is primary testing machine config, lm12luu based box with 35x35x30 working area
-
-include <inc/metric.scad>;
-include <inc/conf_bushing.scad>;
-
-// Custom settings here, tailor to your supplies and print settings
-
-layer_height = 0.3;
-width_over_thickness = 2.2;
-
-// Select your belt type ******************************************************
-
-//T2.5
-//belt_tooth_distance = 2.5;
-//belt_tooth_ratio = 0.5;
-
-//T5 (strongly discouraged)
-//belt_tooth_distance = 5;
-//belt_tooth_ratio = 0.75;
-
-//HTD3
-belt_tooth_distance = 3;
-belt_tooth_ratio = 0.75;
-
-//MXL
-//belt_tooth_distance = 2.032;
-//belt_tooth_ratio = 0.64;
-
-//GT2 there is bunch of GT2 belts with different tooth-to-tooth distance
-//adjust to your needs
-//belt_tooth_distance = 2;
-//belt_tooth_ratio = 0.5;
-
-// For T type belts you will probably want 0.8mm or so.
-belt_thickness = 1.75;
-
-// Choose bearing/bushing configuration ***************************************
-// conf_b_* are in inc/conf_bushing.scad
-
-bushing_xy = conf_b_lm12luu;
-bushing_z = conf_b_lm12luu;
-// for longer bearings use one shorter in x-carriage to make place for belt attachment
-// by default use same as xy
-bushing_carriage = conf_b_lm12uu;
-
-// Select idler bearing size **************************************************
-// [outer_diameter, width, inner_diameter, uses_guide]
-// 608 [standard skate bearings] with bearing guide
-bearing_608 = [22, 7, 8, 1];
-//608 bearings with fender washers
-bearing_608_washers = [22, 10, 8, 0];
-// 624 [roughly same diameter as pulley, makes belt parallel so its prettier]
-bearing_624 = [16, 5, 4, 1];
-// two 624 - for use without bearing guides. My favourite [ax]
-bearing_624_double = [16, 10, 4, 0];
-
-idler_bearing = bearing_624_double;
-
-// Fillets ********************************************************************
-// mostly cosmetic, except z axis.
-// 0 = no fillets
-// 1 = fillet
-
-use_fillets = 1;
-
-//set to 0 for single plate (affects z axis)
-i_am_box = 1;
-
-//if you do your own plate and can move bottom Z screws 5mm up set this to 0 to
-//get stronger motor mount. Only for i_am_box = 0
-i_want_to_use_single_plate_dxf_and_make_my_z_weaker = 1;
-
-//radius of long threaded rod on Y frame
-//Use 5.4 for M10 or 4.4 for M8
-y_threaded_rod_long_r = 5.4;
-
-// Thickness of the XZ plate board. Leave at 12 for single plate
-board_thickness = 18;
-
-// END of custom settings
-
-
-// You are not supposed to change this
-board_to_xz_distance = 26;
-xaxis_rod_distance = 45;
-
-//calculated from settings
-single_wall_width = width_over_thickness * layer_height;
-
-idler_width = (idler_bearing[1] > 7 ? idler_bearing[1] : 7) + 2.5 * idler_bearing[3] ;
-
-//deltas are used to enlarge parts for bigger bearings
-xy_delta = ((bushing_xy[1] <= 7.7) ? 0 : bushing_xy[1] - 7.7) * 0.9;
-z_delta = (bushing_z[1] <= 7.7) ? 0 : bushing_z[1] - 7.7;
-
-// CHANGE ONLY THE STUFF YOU KNOW
-// IT WILL REPLACE DEFAULT SETTING
-
-// RODS
-
-// threaded_rod_diameter = 0;
-// threaded_rod_diameter_horizontal = 0;
-// smooth_bar_diameter = 0;
-// smooth_bar_diameter_horizontal = 0;
-
-// Nuts and bolts
-
-// m8_diameter = 0;
-// m8_nut_diameter = 0;
-
-// m4_diameter = 0;
-// m4_nut_diameter = 0;
-
-// m3_diameter = 0;
-// m3_nut_diameter = 0;
-
-// Bushing holder
-
-// bushing_core_diameter = smooth_bar_diameter;
-// bushing_material_thickness = 0;
-
-///counted stuff
-m3_nut_diameter_bigger = ((m3_nut_diameter / 2) / cos (180 / 6))*2;
-
-// functions
-include <inc/functions.scad>
-
-// These constants define the geometry of the complete-printer.scad
-
-//x_smooth_rod_length=325;
-//y_smooth_rod_length=405;
-//z_smooth_rod_length=235;
-bed_x_size=350;
-bed_y_size=350;
-
-x_smooth_rod_length=460+board_thickness*2; // 492 for 16mm thickness; 484 for 12mm thickness
-y_smooth_rod_length=470;
-z_smooth_rod_length=405;
+++ /dev/null
-// PRUSA iteration3
-// Configuration file
-// GNU GPL v3
-// Josef Průša <josefprusa@me.com>
-// Václav 'ax' Hůla <axtheb@gmail.com>
-// http://www.reprap.org/wiki/Prusa_Mendel
-// http://github.com/prusajr/PrusaMendel
-
-// This configuration mimics single_plate
-// with Contitech HTD 3m belts
-
-include <inc/metric.scad>;
-include <inc/conf_bushing.scad>;
-
-// Custom settings here, tailor to your supplies and print settings
-
-layer_height = 0.3;
-width_over_thickness = 2.2;
-
-// Select your belt type ******************************************************
-
-//T2.5
-//belt_tooth_distance = 2.5;
-//belt_tooth_ratio = 0.5;
-
-//T5 (strongly discouraged)
-//belt_tooth_distance = 5;
-//belt_tooth_ratio = 0.75;
-
-//HTD3
-belt_tooth_distance = 3;
-belt_tooth_ratio = 0.75;
-
-//MXL
-//belt_tooth_distance = 2.032;
-//belt_tooth_ratio = 0.64;
-
-//GT2 there is bunch of GT2 belts with different tooth-to-tooth distance
-//adjust to your needs
-//belt_tooth_distance = 2;
-//belt_tooth_ratio = 0.5;
-
-// For T type belts you will probably want 0.8mm or so.
-belt_thickness = 1.75;
-
-// Choose bearing/bushing configuration ***************************************
-// conf_b_* are in inc/conf_bushing.scad
-
-bushing_xy = conf_b_lm8uu;
-bushing_z = conf_b_lm8uu;
-// for longer bearings use one shorter in x-carriage to make place for belt attachment
-// by default use same as xy
-bushing_carriage = bushing_xy;
-
-// Select idler bearing size **************************************************
-// [outer_diameter, width, inner_diameter, uses_guide]
-// 608 [standard skate bearings] with bearing guide
-bearing_608 = [22, 7, 8, 1];
-//608 bearings with fender washers
-bearing_608_washers = [22, 10, 8, 0];
-// 624 [roughly same diameter as pulley, makes belt parallel so its prettier]
-bearing_624 = [16, 5, 4, 1];
-// two 624 - for use without bearing guides. My favourite [ax]
-bearing_624_double = [16, 10, 4, 0];
-
-idler_bearing = bearing_624_double;
-
-// Fillets ********************************************************************
-// mostly cosmetic, except z axis.
-// 0 = no fillets
-// 1 = fillet
-
-use_fillets = 1;
-
-//set to 0 for single plate (affects z axis)
-i_am_box = 0;
-
-//if you do your own plate and can move bottom Z screws 5mm up set this to 0 to
-//get stronger motor mount. Only for i_am_box = 0
-i_want_to_use_single_plate_dxf_and_make_my_z_weaker = 1;
-
-//radius of long threaded rod on Y frame
-//Use 5.4 for M10 or 4.4 for M8
-y_threaded_rod_long_r = 5.4;
-
-// Thickness of the XZ plate board. Leave at 12 for single plate
-board_thickness = 12;
-
-// END of custom settings
-
-
-// You are not supposed to change this
-board_to_xz_distance = 26;
-xaxis_rod_distance = 45;
-
-//calculated from settings
-single_wall_width = width_over_thickness * layer_height;
-
-idler_width = (idler_bearing[1] > 7 ? idler_bearing[1] : 7) + 2.5 * idler_bearing[3] ;
-
-//deltas are used to enlarge parts for bigger bearings
-xy_delta = ((bushing_xy[1] <= 7.7) ? 0 : bushing_xy[1] - 7.7) * 0.9;
-z_delta = (bushing_z[1] <= 7.7) ? 0 : bushing_z[1] - 7.7;
-
-// CHANGE ONLY THE STUFF YOU KNOW
-// IT WILL REPLACE DEFAULT SETTING
-
-// RODS
-
-// threaded_rod_diameter = 0;
-// threaded_rod_diameter_horizontal = 0;
-// smooth_bar_diameter = 0;
-// smooth_bar_diameter_horizontal = 0;
-
-// Nuts and bolts
-
-// m8_diameter = 0;
-// m8_nut_diameter = 0;
-
-// m4_diameter = 0;
-// m4_nut_diameter = 0;
-
-// m3_diameter = 0;
-// m3_nut_diameter = 0;
-
-// Bushing holder
-
-// bushing_core_diameter = smooth_bar_diameter;
-// bushing_material_thickness = 0;
-
-///counted stuff
-m3_nut_diameter_bigger = ((m3_nut_diameter / 2) / cos (180 / 6))*2;
-
-// functions
-include <inc/functions.scad>
-
-// These constants define the geometry of the complete-printer.scad
-
-//x_smooth_rod_length=325;
-//y_smooth_rod_length=405;
-//z_smooth_rod_length=235;
-bed_x_size=225;
-bed_y_size=225;
-
-x_smooth_rod_length=460+board_thickness*2; // 492 for 16mm thickness; 484 for 12mm thickness
-y_smooth_rod_length=470;
-z_smooth_rod_length=405;
HCoop / clinton / prusa3.git / commitdiff