--- /dev/null
+// PRUSA iteration3
+// Configuration file
+// GNU GPL v3
+// Josef Průša <josefprusa@me.com>
+// Václav 'ax' Hůla <axtheb@gmail.com>
+// http://www.reprap.org/wiki/Prusa_Mendel
+// http://github.com/prusajr/PrusaMendel
+
+// This is primary testing machine config, lm12luu based box with 35x35x30 working area
+
+include <inc/metric.scad>;
+include <inc/conf_bushing.scad>;
+
+// Custom settings here, tailor to your supplies and print settings
+
+layer_height = 0.3;
+width_over_thickness = 2.2;
+
+// Select your belt type ******************************************************
+
+//T2.5
+//belt_tooth_distance = 2.5;
+//belt_tooth_ratio = 0.5;
+
+//T5 (strongly discouraged)
+//belt_tooth_distance = 5;
+//belt_tooth_ratio = 0.75;
+
+//HTD3
+belt_tooth_distance = 3;
+belt_tooth_ratio = 0.75;
+
+//MXL
+//belt_tooth_distance = 2.032;
+//belt_tooth_ratio = 0.64;
+
+//GT2 there is bunch of GT2 belts with different tooth-to-tooth distance
+//adjust to your needs
+//belt_tooth_distance = 2;
+//belt_tooth_ratio = 0.5;
+
+// For T type belts you will probably want 0.8mm or so.
+belt_thickness = 1.75;
+
+// Choose bearing/bushing configuration ***************************************
+// conf_b_* are in inc/conf_bushing.scad
+
+bushing_xy = conf_b_lm12luu;
+bushing_z = conf_b_lm12luu;
+// for longer bearings use one shorter in x-carriage to make place for belt attachment
+// by default use same as xy
+bushing_carriage = conf_b_lm12uu;
+
+// Select idler bearing size **************************************************
+// [outer_diameter, width, inner_diameter, uses_guide]
+// 608 [standard skate bearings] with bearing guide
+bearing_608 = [22, 7, 8, 1];
+//608 bearings with fender washers
+bearing_608_washers = [22, 10, 8, 0];
+// 624 [roughly same diameter as pulley, makes belt parallel so its prettier]
+bearing_624 = [16, 5, 4, 1];
+// two 624 - for use without bearing guides. My favourite [ax]
+bearing_624_double = [16, 10, 4, 0];
+
+idler_bearing = bearing_624_double;
+
+// Fillets ********************************************************************
+// mostly cosmetic, except z axis.
+// 0 = no fillets
+// 1 = fillet
+
+use_fillets = 1;
+
+//set to 0 for single plate (affects z axis)
+i_am_box = 1;
+
+//if you do your own plate and can move bottom Z screws 5mm up set this to 0 to
+//get stronger motor mount. Only for i_am_box = 0
+i_want_to_use_single_plate_dxf_and_make_my_z_weaker = 1;
+
+//radius of long threaded rod on Y frame
+//Use 5.4 for M10 or 4.4 for M8
+y_threaded_rod_long_r = 5.4;
+
+// Thickness of the XZ plate board. Leave at 12 for single plate
+board_thickness = 18;
+
+// END of custom settings
+
+
+// You are not supposed to change this
+board_to_xz_distance = 26;
+xaxis_rod_distance = 45;
+
+//calculated from settings
+single_wall_width = width_over_thickness * layer_height;
+
+idler_width = (idler_bearing[1] > 7 ? idler_bearing[1] : 7) + 2.5 * idler_bearing[3] ;
+
+//deltas are used to enlarge parts for bigger bearings
+xy_delta = ((bushing_xy[1] <= 7.7) ? 0 : bushing_xy[1] - 7.7) * 0.9;
+z_delta = (bushing_z[1] <= 7.7) ? 0 : bushing_z[1] - 7.7;
+
+// CHANGE ONLY THE STUFF YOU KNOW
+// IT WILL REPLACE DEFAULT SETTING
+
+// RODS
+
+// threaded_rod_diameter = 0;
+// threaded_rod_diameter_horizontal = 0;
+// smooth_bar_diameter = 0;
+// smooth_bar_diameter_horizontal = 0;
+
+// Nuts and bolts
+
+// m8_diameter = 0;
+// m8_nut_diameter = 0;
+
+// m4_diameter = 0;
+// m4_nut_diameter = 0;
+
+// m3_diameter = 0;
+// m3_nut_diameter = 0;
+
+// Bushing holder
+
+// bushing_core_diameter = smooth_bar_diameter;
+// bushing_material_thickness = 0;
+
+///counted stuff
+m3_nut_diameter_bigger = ((m3_nut_diameter / 2) / cos (180 / 6))*2;
+
+// functions
+include <inc/functions.scad>
+
+// These constants define the geometry of the complete-printer.scad
+
+//x_smooth_rod_length=325;
+//y_smooth_rod_length=405;
+//z_smooth_rod_length=235;
+bed_x_size=225;
+bed_y_size=225;
+
+x_smooth_rod_length=460+board_thickness*2; // 492 for 16mm thickness; 484 for 12mm thickness
+y_smooth_rod_length=470;
+z_smooth_rod_length=405;
--- /dev/null
+// PRUSA iteration3
+// Configuration file
+// GNU GPL v3
+// Josef Průša <josefprusa@me.com>
+// Václav 'ax' Hůla <axtheb@gmail.com>
+// http://www.reprap.org/wiki/Prusa_Mendel
+// http://github.com/prusajr/PrusaMendel
+
+// This configuration mimics single_plate
+// with Contitech HTD 3m belts
+
+include <inc/metric.scad>;
+include <inc/conf_bushing.scad>;
+
+// Custom settings here, tailor to your supplies and print settings
+
+layer_height = 0.3;
+width_over_thickness = 2.2;
+
+// Select your belt type ******************************************************
+
+//T2.5
+//belt_tooth_distance = 2.5;
+//belt_tooth_ratio = 0.5;
+
+//T5 (strongly discouraged)
+//belt_tooth_distance = 5;
+//belt_tooth_ratio = 0.75;
+
+//HTD3
+belt_tooth_distance = 3;
+belt_tooth_ratio = 0.75;
+
+//MXL
+//belt_tooth_distance = 2.032;
+//belt_tooth_ratio = 0.64;
+
+//GT2 there is bunch of GT2 belts with different tooth-to-tooth distance
+//adjust to your needs
+//belt_tooth_distance = 2;
+//belt_tooth_ratio = 0.5;
+
+// For T type belts you will probably want 0.8mm or so.
+belt_thickness = 1.75;
+
+// Choose bearing/bushing configuration ***************************************
+// conf_b_* are in inc/conf_bushing.scad
+
+bushing_xy = conf_b_lm8uu;
+bushing_z = conf_b_lm8uu;
+// for longer bearings use one shorter in x-carriage to make place for belt attachment
+// by default use same as xy
+bushing_carriage = bushing_xy;
+
+// Select idler bearing size **************************************************
+// [outer_diameter, width, inner_diameter, uses_guide]
+// 608 [standard skate bearings] with bearing guide
+bearing_608 = [22, 7, 8, 1];
+//608 bearings with fender washers
+bearing_608_washers = [22, 10, 8, 0];
+// 624 [roughly same diameter as pulley, makes belt parallel so its prettier]
+bearing_624 = [16, 5, 4, 1];
+// two 624 - for use without bearing guides. My favourite [ax]
+bearing_624_double = [16, 10, 4, 0];
+
+idler_bearing = bearing_624_double;
+
+// Fillets ********************************************************************
+// mostly cosmetic, except z axis.
+// 0 = no fillets
+// 1 = fillet
+
+use_fillets = 1;
+
+//set to 0 for single plate (affects z axis)
+i_am_box = 0;
+
+//if you do your own plate and can move bottom Z screws 5mm up set this to 0 to
+//get stronger motor mount. Only for i_am_box = 0
+i_want_to_use_single_plate_dxf_and_make_my_z_weaker = 1;
+
+//radius of long threaded rod on Y frame
+//Use 5.4 for M10 or 4.4 for M8
+y_threaded_rod_long_r = 5.4;
+
+// Thickness of the XZ plate board. Leave at 12 for single plate
+board_thickness = 12;
+
+// END of custom settings
+
+
+// You are not supposed to change this
+board_to_xz_distance = 26;
+xaxis_rod_distance = 45;
+
+//calculated from settings
+single_wall_width = width_over_thickness * layer_height;
+
+idler_width = (idler_bearing[1] > 7 ? idler_bearing[1] : 7) + 2.5 * idler_bearing[3] ;
+
+//deltas are used to enlarge parts for bigger bearings
+xy_delta = ((bushing_xy[1] <= 7.7) ? 0 : bushing_xy[1] - 7.7) * 0.9;
+z_delta = (bushing_z[1] <= 7.7) ? 0 : bushing_z[1] - 7.7;
+
+// CHANGE ONLY THE STUFF YOU KNOW
+// IT WILL REPLACE DEFAULT SETTING
+
+// RODS
+
+// threaded_rod_diameter = 0;
+// threaded_rod_diameter_horizontal = 0;
+// smooth_bar_diameter = 0;
+// smooth_bar_diameter_horizontal = 0;
+
+// Nuts and bolts
+
+// m8_diameter = 0;
+// m8_nut_diameter = 0;
+
+// m4_diameter = 0;
+// m4_nut_diameter = 0;
+
+// m3_diameter = 0;
+// m3_nut_diameter = 0;
+
+// Bushing holder
+
+// bushing_core_diameter = smooth_bar_diameter;
+// bushing_material_thickness = 0;
+
+///counted stuff
+m3_nut_diameter_bigger = ((m3_nut_diameter / 2) / cos (180 / 6))*2;
+
+// functions
+include <inc/functions.scad>
+
+// These constants define the geometry of the complete-printer.scad
+
+//x_smooth_rod_length=325;
+//y_smooth_rod_length=405;
+//z_smooth_rod_length=235;
+bed_x_size=225;
+bed_y_size=225;
+
+x_smooth_rod_length=460+board_thickness*2; // 492 for 16mm thickness; 484 for 12mm thickness
+y_smooth_rod_length=470;
+z_smooth_rod_length=405;
HCoop / clinton / prusa3.git / commitdiff