clinton/Smoothieware.git
2013-09-24 Jim Morrisadd M117 to add an arbitrary LCD message
2013-09-22 Jim MorrisMerge pull request #238 from wolfmanjm/upstreamedge
2013-09-22 Jim MorrisAdded Adams Heapwalk to determine amount of unallocated...
2013-09-22 Jim MorrisMerge pull request #237 from wolfmanjm/upstreamedge
2013-09-22 Jim MorrisClear the config cache just before the main loop starts...
2013-09-22 Jim MorrisMerge pull request #236 from wolfmanjm/upstreamedge
2013-09-22 Jim Morrisadd mem command to see free ram
2013-09-22 Jim MorrisMerge pull request #235 from TopherMan/feature/extruder...
2013-09-22 Chris GeorgeM18 and M84 now accept E to disable only the extruder...
2013-09-22 Chris GeorgeMade M17 and M18 apply to extruder as well as steppers.
2013-09-18 Jim MorrisMerge pull request #232 from wuflnor/edge
2013-09-18 wuflnorfix glyph display
2013-09-17 wuflnoradd selection of st7565
2013-09-17 wuflnoradd st7565 support
2013-09-17 Jim MorrisMerge pull request #231 from TopherMan/fix/M23
2013-09-17 Chris GeorgeAdded dummy M21 so OctoPrint will play nice.
2013-09-17 Chris GeorgeAdjust M23/M24 so that size is calculated and reported...
2013-09-13 Jim MorrisMerge pull request #230 from TopherMan/feature/M27more
2013-09-13 Chris GeorgeRookie mistake. Forgot carriage return/newline.
2013-09-13 Chris GeorgeAdded -b switch to progress to report bytes, and made...
2013-09-13 Jim MorrisMerge pull request #229 from wolfmanjm/upstreamedge
2013-09-13 Jim MorrisFix speed changing via panel, just donlt swicth away...
2013-09-12 Jim MorrisMerge pull request #228 from TopherMan/feature/M27
2013-09-12 Chris GeorgeAdded M27. Identical to progress.
2013-09-12 Jim MorrisMerge pull request #227 from wolfmanjm/upstreamedge
2013-09-12 Jim Morrisfix potential rounding issues wth COREXY arm solution
2013-09-12 Jim MorrisMerge pull request #226 from wolfmanjm/add/m-commands...
2013-09-12 Jim MorrisAdded M23, M24, M25, M32 and M20 which allow pronterfac...
2013-09-01 Jim MorrisMerge pull request #224 from wolfmanjm/upstreamedge
2013-09-01 Jim MorrisAdd delta_homing config to forace all towers to home...
2013-08-30 Jim MorrisMerge pull request #223 from wolfmanjm/upstreamedge
2013-08-30 Jim Morristruncate characters that woudl wrap on glcd
2013-08-29 Jim MorrisMerge pull request #222 from wolfmanjm/upstreamedge
2013-08-29 Jim MorrisMake M303 parameters auto pid tune compliant with other...
2013-08-28 Jim MorrisMerge pull request #221 from wolfmanjm/upstreamedge
2013-08-28 Jim Morrisadd example pid control settings
2013-08-27 Jim MorrisMerge pull request #219 from wolfmanjm/fix/pid2
2013-08-27 Jim MorrisAllow auto pid to use full power
2013-08-27 Jim MorrisMake PID work like arduino pid library and more like...
2013-08-18 Adam GreenFix mbed build on Windows machines with Cygwin
2013-08-13 Jim MorrisMerge pull request #216 from wolfmanjm/fix/pid
2013-08-13 Jim MorrisSetting the I and D values needs to be scaled by the...
2013-08-09 Arthur Wolfmake pwm frequency configurable in temperaturecontrol...
2013-08-08 Jim MorrisMerge pull request #215 from wolfmanjm/upstreamedge
2013-08-08 Jim Morrismake minimum M220 speed 10% otherwise wierd things...
2013-08-07 Jim MorrisMerge pull request #214 from wolfmanjm/upstreamedge
2013-08-07 Jim MorrisUse ahbmalloc() to dynamically allocate usb ram for...
2013-08-07 Jim MorrisMerge pull request #213 from wolfmanjm/upstreamedge
2013-08-07 Jim Morristemporarily ifdef out the ethernet stuff
2013-08-07 Jim MorrisMerge pull request #212 from wolfmanjm/fix/glcd-frambuffer
2013-08-07 Jim Morrismove glcd framebuffer into USB RAM as there is not...
2013-08-07 Jim MorrisUpdate ReprapDiscountGLCD.cpp
2013-08-07 Jim MorrisMerge pull request #211 from wolfmanjm/upstreamedge
2013-08-07 Jim Morrischange config trim values sign to match that set in...
2013-08-06 Jim MorrisMerge pull request #210 from wolfmanjm/feature/hbot...
2013-08-06 Jim Morrisremove last debug printf from homing
2013-08-06 Jim Morrischeck both corexy motors for stop
2013-08-06 Jim Morristurn off both motors when endstop is hit for corexy
2013-08-06 Jim Morrisudate delta config for homing
2013-08-06 Jim Morrisadd corexy_homing to sample config
2013-08-06 Jim MorrisConvert the endstop/homing configs to mm and mm/sec
2013-08-06 Jim Morrisadded hbot/corexy homing
2013-08-06 Jim MorrisOnly show endstops that are used (either min or max)
2013-08-06 Jim MorrisAllow trim values to be negative to trim up
2013-08-06 Jim MorrisIncrease glcd refresh rate to 10Hz
2013-08-04 Jim MorrisMerge pull request #209 from wolfmanjm/upstreamedge
2013-08-04 Jim Morrismake bitmap const so it goes into flash
2013-08-04 Jim MorrisMerge pull request #208 from wolfmanjm/optimize/glcd...
2013-08-04 Jim Morrisadd open hardware logo on startup screen for glcd
2013-08-03 Jim MorrisMerge pull request #207 from wolfmanjm/optimize/glcd...
2013-08-03 Jim MorrisOptimize graphic font rendering for glc, using x aligne...
2013-08-02 Jim Morrisadded kill/pause button config for panels
2013-08-02 Jim Morrismove the encoder pins used for the panels
2013-08-02 Jim MorrisAdd RRD GLCD comments
2013-08-02 Arthur WolfMerge pull request #206 from Extent421/edge
2013-08-02 Mark Medranocleaned up unused members, added a few comments
2013-08-02 Mark Medranoadded endstop soft trim in preparation for deltabot...
2013-08-02 Mark Medranokeep track of remainder amount from distance->step...
2013-08-02 Jim MorrisMerge pull request #205 from wolfmanjm/feature/add...
2013-08-02 Jim Morrisadd glyph blit operatin to gcld
2013-08-01 Jim MorrisMerge pull request #204 from wolfmanjm/feature/rrd...
2013-08-01 Jim Morrischane speed changes via panel to issue M220 to avoid...
2013-08-01 Jim Morriscap speed override to not less than 1%
2013-07-31 Jim Morrisonly refresh framebuffer if it is dirty
2013-07-31 Jim Morrisoptimize panel to display lines not characters
2013-07-31 Jim Morrisupdate config
2013-07-31 Jim Morrisswitch to graphic fonts
2013-07-31 Jim Morrisreprap discount panel working in character mode.
2013-07-27 Jim MorrisUpdate config
2013-07-27 Jim MorrisUpdate config
2013-07-27 Jim MorrisFix endstop configuration
2013-07-18 LogxenMerge remote-tracking branch 'upstream/stable-edge...
2013-07-18 Logxenrevert to pre-actuator state
2013-07-09 Jim MorrisAdd hack to detect i2c timeout, and reset Viki LCD...
2013-07-07 Arthur Wolfadding virtuals to Actuator origin/actuator
2013-07-06 Arthur Wolfmoving all modules to use Actuator instead of StepperMo...
2013-07-06 Arthur Wolfforgot Actuator.h
2013-07-06 Arthur WolfStepticker now inherits Actuator
2013-07-06 Arthur Wolfmoving StepperMotor.h to actuators/
2013-07-06 Jim MorrisAdd new panel examples
next