1 # Smoothieboard configuration file, see http://smoothieware.org/configuring-smoothie
2 # NOTE Lines must not exceed 132 characters, and '#' characters mean what follows is ignored
3 ## Robot module configurations : general handling of movement G-codes and slicing into moves
5 # Basic motion configuration
6 default_feed_rate 4000 # Default speed (mm/minute) for G1/G2/G3 moves
7 default_seek_rate 4000 # Default speed (mm/minute) for G0 moves
8 mm_per_arc_segment 0.0 # Fixed length for line segments that divide arcs, 0 to disable
9 #mm_per_line_segment 5 # Cut lines into segments this size
10 mm_max_arc_error 0.01 # The maximum error for line segments that divide arcs 0 to disable
11 # note it is invalid for both the above be 0
12 # if both are used, will use largest segment length based on radius
14 # Arm solution configuration : Cartesian robot. Translates mm positions into stepper positions
15 # See http://smoothieware.org/stepper-motors
16 alpha_steps_per_mm 80 # Steps per mm for alpha ( X ) stepper
17 beta_steps_per_mm 80 # Steps per mm for beta ( Y ) stepper
18 gamma_steps_per_mm 1600 # Steps per mm for gamma ( Z ) stepper
20 # Planner module configuration : Look-ahead and acceleration configuration
21 # See http://smoothieware.org/motion-control
22 acceleration 3000 # Acceleration in mm/second/second.
23 #z_acceleration 500 # Acceleration for Z only moves in mm/s^2, 0 uses acceleration which is the default. DO NOT SET ON A DELTA
24 junction_deviation 0.05 # See http://smoothieware.org/motion-control#junction-deviation
25 #z_junction_deviation 0.0 # For Z only moves, -1 uses junction_deviation, zero disables junction_deviation on z moves DO NOT SET ON A DELTA
27 # Cartesian axis speed limits
28 x_axis_max_speed 30000 # Maximum speed in mm/min
29 y_axis_max_speed 30000 # Maximum speed in mm/min
30 z_axis_max_speed 300 # Maximum speed in mm/min
32 # Stepper module configuration
33 # Pins are defined as ports, and pin numbers, appending "!" to the number will invert a pin
34 # See http://smoothieware.org/pin-configuration and http://smoothieware.org/pinout
35 alpha_step_pin 2.0 # Pin for alpha stepper step signal
36 alpha_dir_pin 0.5 # Pin for alpha stepper direction, add '!' to reverse direction
37 alpha_en_pin 0.4 # Pin for alpha enable pin
38 alpha_current 1.5 # X stepper motor current
39 alpha_max_rate 30000.0 # Maximum rate in mm/min
41 beta_step_pin 2.1 # Pin for beta stepper step signal
42 beta_dir_pin 0.11 # Pin for beta stepper direction, add '!' to reverse direction
43 beta_en_pin 0.10 # Pin for beta enable
44 beta_current 1.5 # Y stepper motor current
45 beta_max_rate 30000.0 # Maxmimum rate in mm/min
47 gamma_step_pin 2.2 # Pin for gamma stepper step signal
48 gamma_dir_pin 0.20 # Pin for gamma stepper direction, add '!' to reverse direction
49 gamma_en_pin 0.19 # Pin for gamma enable
50 gamma_current 1.5 # Z stepper motor current
51 gamma_max_rate 300.0 # Maximum rate in mm/min
53 ## Extruder module configuration
54 # See http://smoothieware.org/extruder
55 extruder.hotend.enable true # Whether to activate the extruder module at all. All configuration is ignored if false
56 extruder.hotend.steps_per_mm 140 # Steps per mm for extruder stepper
57 extruder.hotend.default_feed_rate 600 # Default rate ( mm/minute ) for moves where only the extruder moves
58 extruder.hotend.acceleration 500 # Acceleration for the stepper motor mm/sec²
59 extruder.hotend.max_speed 50 # Maximum speed in mm/s
61 extruder.hotend.step_pin 2.3 # Pin for extruder step signal
62 extruder.hotend.dir_pin 0.22 # Pin for extruder dir signal ( add '!' to reverse direction )
63 extruder.hotend.en_pin 0.21 # Pin for extruder enable signal
66 #extruder.hotend.x_offset 0 # X offset from origin in mm
67 #extruder.hotend.y_offset 0 # Y offset from origin in mm
68 #extruder.hotend.z_offset 0 # Z offset from origin in mm
70 # Firmware retract settings when using G10/G11, these are the defaults if not defined, must be defined for each extruder if not using the defaults
71 #extruder.hotend.retract_length 3 # Retract length in mm
72 #extruder.hotend.retract_feedrate 45 # Retract feedrate in mm/sec
73 #extruder.hotend.retract_recover_length 0 # Additional length for recover
74 #extruder.hotend.retract_recover_feedrate 8 # Recover feedrate in mm/sec (should be less than retract feedrate)
75 #extruder.hotend.retract_zlift_length 0 # Z-lift on retract in mm, 0 disables
76 #extruder.hotend.retract_zlift_feedrate 6000 # Z-lift feedrate in mm/min (Note mm/min NOT mm/sec)
78 delta_current 1.5 # First extruder stepper motor current
80 # Second extruder module configuration
81 #extruder.hotend2.enable true # Whether to activate the extruder module at all. All configuration is ignored if false
82 #extruder.hotend2.steps_per_mm 140 # Steps per mm for extruder stepper
83 #extruder.hotend2.default_feed_rate 600 # Default rate ( mm/minute ) for moves where only the extruder moves
84 #extruder.hotend2.acceleration 500 # Acceleration for the stepper motor, as of 0.6, arbitrary ratio
85 #extruder.hotend2.max_speed 50 # mm/s
87 #extruder.hotend2.step_pin 2.8 # Pin for extruder step signal
88 #extruder.hotend2.dir_pin 2.13 # Pin for extruder dir signal ( add '!' to reverse direction )
89 #extruder.hotend2.en_pin 4.29 # Pin for extruder enable signal
91 #extruder.hotend2.x_offset 0 # x offset from origin in mm
92 #extruder.hotend2.y_offset 25.0 # y offset from origin in mm
93 #extruder.hotend2.z_offset 0 # z offset from origin in mm
95 #epsilon_current 1.5 # Second extruder stepper motor current
98 ## Laser module configuration
99 # See http://smoothieware.org/laser
100 laser_module_enable false # Whether to activate the laser module at all
101 laser_module_pwm_pin 2.5 # This pin will be PWMed to control the laser.
102 # Only pins 2.0, 2.1, 2.2, 2.3, 2.4, 2.5, 1.18, 1.20, 1.21, 1.23, 1.24, 1.26, 3.25 and 3.26
103 # can be used since laser requires hardware PWM, see http://smoothieware.org/pinout
104 #laser_module_ttl_pin 1.30 # This pin turns on when the laser turns on, and off when the laser turns off.
105 #laser_module_maximum_power 1.0 # This is the maximum duty cycle that will be applied to the laser
106 #laser_module_minimum_power 0.0 # This is a value just below the minimum duty cycle that keeps the laser
107 # active without actually burning.
108 #laser_module_default_power 0.8 # This is the default laser power that will be used for cuts if a power has not been specified. The value is a scale between
109 # the maximum and minimum power levels specified above
110 #laser_module_pwm_period 20 # This sets the pwm frequency as the period in microseconds
112 ## Temperature control configuration
113 # See http://smoothieware.org/temperaturecontrol
115 # First hotend configuration
116 temperature_control.hotend.enable true # Whether to activate this ( "hotend" ) module at all.
117 temperature_control.hotend.thermistor_pin 0.23 # Pin for the thermistor to read
118 temperature_control.hotend.heater_pin 2.7 # Pin that controls the heater, set to nc if a readonly thermistor is being defined
119 temperature_control.hotend.thermistor EPCOS100K # See http://smoothieware.org/temperaturecontrol#toc5
120 #temperature_control.hotend.beta 4066 # Or set the beta value
121 temperature_control.hotend.set_m_code 104 # M-code to set the temperature for this module
122 temperature_control.hotend.set_and_wait_m_code 109 # M-code to set-and-wait for this module
123 temperature_control.hotend.designator T # Designator letter for this module
124 #temperature_control.hotend.max_temp 300 # Set maximum temperature - Will prevent heating above 300 by default
125 #temperature_control.hotend.min_temp 0 # Set minimum temperature - Will prevent heating below if set
127 # Safety control is enabled by default and can be overidden here, the values show the defaults
128 # See http://smoothieware.org/temperaturecontrol#runaway
129 #temperature_control.hotend.runaway_heating_timeout 900 # How long it can take to heat up, max is 2040 seconds.
130 #temperature_control.hotend.runaway_cooling_timeout 0 # How long it can take to cool down if temp is set lower, max is 2040 seconds
131 #temperature_control.hotend.runaway_range 20 # How far from the set temperature it can wander, max setting is 63°C
134 # See http://smoothieware.org/temperaturecontrol#pid
135 #temperature_control.hotend.p_factor 13.7 # P ( proportional ) factor
136 #temperature_control.hotend.i_factor 0.097 # I ( integral ) factor
137 #temperature_control.hotend.d_factor 24 # D ( derivative ) factor
139 #temperature_control.hotend.max_pwm 64 # Max pwm, 64 is a good value if driving a 12v resistor with 24v.
141 # Second hotend configuration
142 #temperature_control.hotend2.enable true # Whether to activate this ( "hotend" ) module at all.
143 #temperature_control.hotend2.thermistor_pin 0.25 # Pin for the thermistor to read
144 #temperature_control.hotend2.heater_pin 1.23 # Pin that controls the heater
145 #temperature_control.hotend2.thermistor EPCOS100K # See http://smoothieware.org/temperaturecontrol#thermistor
146 ##temperature_control.hotend2.beta 4066 # or set the beta value
147 #temperature_control.hotend2.set_m_code 104 # M-code to set the temperature for this module
148 #temperature_control.hotend2.set_and_wait_m_code 109 # M-code to set-and-wait for this module
149 #temperature_control.hotend2.designator T1 # Designator letter for this module
151 #temperature_control.hotend2.p_factor 13.7 # P ( proportional ) factor
152 #temperature_control.hotend2.i_factor 0.097 # I ( integral ) factor
153 #temperature_control.hotend2.d_factor 24 # D ( derivative ) factor
155 #temperature_control.hotend2.max_pwm 64 # Max pwm, 64 is a good value if driving a 12v resistor with 24v.
157 temperature_control.bed.enable true # Whether to activate this ( "hotend" ) module at all.
158 temperature_control.bed.thermistor_pin 0.24 # Pin for the thermistor to read
159 temperature_control.bed.heater_pin 2.5 # Pin that controls the heater
160 temperature_control.bed.thermistor Honeywell100K # See http://smoothieware.org/temperaturecontrol#thermistor
161 #temperature_control.bed.beta 3974 # Or set the beta value
162 temperature_control.bed.set_m_code 140 # M-code to set the temperature for this module
163 temperature_control.bed.set_and_wait_m_code 190 # M-code to set-and-wait for this module
164 temperature_control.bed.designator B # Designator letter for this module
166 # Bang-bang ( simplified ) control
167 # See http://smoothieware.org/temperaturecontrol#bang-bang
168 #temperature_control.bed.bang_bang false # Set to true to use bang bang control rather than PID
169 #temperature_control.bed.hysteresis 2.0 # Set to the temperature in degrees C to use as hysteresis
172 # See http://smoothieware.org/switch
174 # Switch module for fan control
175 switch.fan.enable true # Enable this module
176 switch.fan.input_on_command M106 # Command that will turn this switch on
177 switch.fan.input_off_command M107 # Command that will turn this switch off
178 switch.fan.output_pin 2.6 # Pin this module controls
179 switch.fan.output_type pwm # PWM output settable with S parameter in the input_on_comand
180 #switch.fan.max_pwm 255 # Set max pwm for the pin default is 255
182 #switch.misc.enable true # Enable this module
183 #switch.misc.input_on_command M42 # Command that will turn this switch on
184 #switch.misc.input_off_command M43 # Command that will turn this switch off
185 #switch.misc.output_pin 2.4 # Pin this module controls
186 #switch.misc.output_type digital # Digital means this is just an on or off pin
189 # See http://smoothieware.org/temperatureswitch
190 # Automatically toggle a switch at a specified temperature. Different ones of these may be defined to monitor different temperatures and switch different swithxes
191 # Useful to turn on a fan or water pump to cool the hotend
192 #temperatureswitch.hotend.enable true #
193 #temperatureswitch.hotend.designator T # first character of the temperature control designator to use as the temperature sensor to monitor
194 #temperatureswitch.hotend.switch misc # select which switch to use, matches the name of the defined switch
195 #temperatureswitch.hotend.threshold_temp 60.0 # temperature to turn on (if rising) or off the switch
196 #temperatureswitch.hotend.heatup_poll 15 # poll heatup at 15 sec intervals
197 #temperatureswitch.hotend.cooldown_poll 60 # poll cooldown at 60 sec intervals
200 # See http://smoothieware.org/endstops
201 endstops_enable true # The endstop module is enabled by default and can be disabled here
202 #corexy_homing false # Set to true if homing on a hbot or corexy
203 alpha_min_endstop 1.24^ # Pin to read min endstop, add a ! to invert if endstop is NO connected to ground
204 #alpha_max_endstop 1.25^ # Pin to read max endstop, uncomment this and comment the above if using max endstops
205 alpha_homing_direction home_to_min # Or set to home_to_max and set alpha_max and uncomment the alpha_max_endstop
206 alpha_min 0 # This gets loaded as the current position after homing when home_to_min is set
207 alpha_max 200 # This gets loaded as the current position after homing when home_to_max is set
208 beta_min_endstop 1.26^ # Pin to read min endstop, add a ! to invert if endstop is NO connected to ground
209 #beta_max_endstop 1.27^ # Pin to read max endstop, uncomment this and comment the above if using max endstops
210 beta_homing_direction home_to_min # Or set to home_to_max and set alpha_max and uncomment the alpha_max_endstop
211 beta_min 0 # This gets loaded as the current position after homing when home_to_min is set
212 beta_max 200 # This gets loaded as the current position after homing when home_to_max is set
213 gamma_min_endstop 1.28^ # Pin to read min endstop, add a ! to invert if endstop is NO connected to ground
214 #gamma_max_endstop 1.29^ # Pin to read max endstop, uncomment this and comment the above if using max endstops
215 gamma_homing_direction home_to_min # Or set to home_to_max and set alpha_max and uncomment the alpha_max_endstop
216 gamma_min 0 # This gets loaded as the current position after homing when home_to_min is set
217 gamma_max 200 # This gets loaded as the current position after homing when home_to_max is set
219 alpha_max_travel 500 # Max travel in mm for alpha/X axis when homing
220 beta_max_travel 500 # Max travel in mm for beta/Y axis when homing
221 gamma_max_travel 500 # Max travel in mm for gamma/Z axis when homing
223 # Optional enable limit switches, actions will stop if any enabled limit switch is triggered
224 #alpha_limit_enable false # Set to true to enable X min and max limit switches
225 #beta_limit_enable false # Set to true to enable Y min and max limit switches
226 #gamma_limit_enable false # Set to true to enable Z min and max limit switches
228 # Endstops home at their fast feedrate first, then once the endstop is found they home again at their slow feedrate for accuracy
229 alpha_fast_homing_rate_mm_s 50 # Alpha/X fast homing feedrate in mm/second
230 alpha_slow_homing_rate_mm_s 25 # Alpha/X slow homing feedrate in mm/second
231 beta_fast_homing_rate_mm_s 50 # Beta/Y fast homing feedrate in mm/second
232 beta_slow_homing_rate_mm_s 25 # Beta/Y slow homing feedrate in mm/second
233 gamma_fast_homing_rate_mm_s 4 # Gamma/Z fast homing feedrate in mm/second
234 gamma_slow_homing_rate_mm_s 2 # Gamma/Z slow homing feedrate in mm/second
236 alpha_homing_retract_mm 5 # Distance to retract from the endstop after it is hit for alpha/X
237 beta_homing_retract_mm 5 # Distance to retract from the endstop after it is hit for beta/Y
238 gamma_homing_retract_mm 1 # Distance to retract from the endstop after it is hit for gamma/Z
241 # Optional enable limit switches, actions will stop if any enabled limit switch is triggered (all are set for delta)
242 #alpha_limit_enable false # Set to true to enable X min and max limit switches
243 #beta_limit_enable false # Set to true to enable Y min and max limit switches
244 #gamma_limit_enable false # Set to true to enable Z min and max limit switches
246 # Optional order in which axis will home, default is they all home at the same time,
247 # If this is set it will force each axis to home one at a time in the specified order
248 #homing_order XYZ # X axis followed by Y then Z last
249 #move_to_origin_after_home false # Move XY to 0,0 after homing
250 #endstop_debounce_count 100 # Uncomment if you get noise on your endstops, default is 100
251 #endstop_debounce_ms 1 # Uncomment if you get noise on your endstops, default is 1 millisecond debounce
252 #home_z_first true # Uncomment and set to true to home the Z first, otherwise Z homes after XY
254 # End of endstop config
255 # Delete the above endstop section and uncomment next line and copy and edit Snippets/abc-endstop.config file to enable endstops for ABC axis
256 #include abc-endstop.config
259 # See http://smoothieware.org/zprobe
260 zprobe.enable false # Set to true to enable a zprobe
261 zprobe.probe_pin 1.28!^ # Pin probe is attached to, if NC remove the !
262 zprobe.slow_feedrate 5 # Mm/sec probe feed rate
263 #zprobe.debounce_ms 1 # Set if noisy
264 zprobe.fast_feedrate 100 # Move feedrate mm/sec
265 zprobe.probe_height 5 # How much above bed to start probe
266 #gamma_min_endstop nc # Normally 1.28. Change to nc to prevent conflict,
269 # Example for 3-point levelling strategy, see wiki documentation for other strategies
270 #leveling-strategy.three-point-leveling.enable true # a leveling strategy that probes three points to define a plane and keeps the Z parallel to that plane
271 #leveling-strategy.three-point-leveling.point1 100.0,0.0 # the first probe point (x,y) optional may be defined with M557
272 #leveling-strategy.three-point-leveling.point2 200.0,200.0 # the second probe point (x,y)
273 #leveling-strategy.three-point-leveling.point3 0.0,200.0 # the third probe point (x,y)
274 #leveling-strategy.three-point-leveling.home_first true # home the XY axis before probing
275 #leveling-strategy.three-point-leveling.tolerance 0.03 # the probe tolerance in mm, anything less that this will be ignored, default is 0.03mm
276 #leveling-strategy.three-point-leveling.probe_offsets 0,0,0 # the probe offsets from nozzle, must be x,y,z, default is no offset
277 #leveling-strategy.three-point-leveling.save_plane false # set to true to allow the bed plane to be saved with M500 default is false
280 # See http://smoothieware.org/panel
281 # Please find your panel on the wiki and copy/paste the right configuration here
282 panel.enable false # Set to true to enable the panel code
284 # Example for reprap discount GLCD
285 # on glcd EXP1 is to left and EXP2 is to right, pin 1 is bottom left, pin 2 is top left etc.
286 # +5v is EXP1 pin 10, Gnd is EXP1 pin 9
287 #panel.lcd reprap_discount_glcd #
288 #panel.spi_channel 0 # SPI channel to use ; GLCD EXP1 Pins 3,5 (MOSI, SCLK)
289 #panel.spi_cs_pin 0.16 # SPI chip select ; GLCD EXP1 Pin 4
290 #panel.encoder_a_pin 3.25!^ # Encoder pin ; GLCD EXP2 Pin 3
291 #panel.encoder_b_pin 3.26!^ # Encoder pin ; GLCD EXP2 Pin 5
292 #panel.click_button_pin 1.30!^ # Click button ; GLCD EXP1 Pin 2
293 #panel.buzz_pin 1.31 # Pin for buzzer ; GLCD EXP1 Pin 1
294 #panel.back_button_pin 2.11!^ # Back button ; GLCD EXP2 Pin 8
296 panel.menu_offset 0 # Some panels will need 1 here
298 panel.alpha_jog_feedrate 6000 # X jogging feedrate in mm/min
299 panel.beta_jog_feedrate 6000 # Y jogging feedrate in mm/min
300 panel.gamma_jog_feedrate 200 # Z jogging feedrate in mm/min
302 panel.hotend_temperature 185 # Temp to set hotend when preheat is selected
303 panel.bed_temperature 60 # Temp to set bed when preheat is selected
305 ## Custom menus : Example of a custom menu entry, which will show up in the Custom entry.
306 # NOTE _ gets converted to space in the menu and commands, | is used to separate multiple commands
307 custom_menu.power_on.enable true #
308 custom_menu.power_on.name Power_on #
309 custom_menu.power_on.command M80 #
311 custom_menu.power_off.enable true #
312 custom_menu.power_off.name Power_off #
313 custom_menu.power_off.command M81 #
317 # See http://smoothieware.org/network
318 network.enable false # Enable the ethernet network services
319 network.webserver.enable true # Enable the webserver
320 network.telnet.enable true # Enable the telnet server
321 network.ip_address auto # Use dhcp to get ip address
322 # Uncomment the 3 below to manually setup ip address
323 #network.ip_address 192.168.3.222 # The IP address
324 #network.ip_mask 255.255.255.0 # The ip mask
325 #network.ip_gateway 192.168.3.1 # The gateway address
326 #network.mac_override xx.xx.xx.xx.xx.xx # Override the mac address, only do this if you have a conflict
328 ## System configuration
329 # Serial communications configuration ( baud rate defaults to 9600 if undefined )
330 # For communication over the UART port, *not* the USB/Serial port
331 uart0.baud_rate 115200 # Baud rate for the default hardware ( UART ) serial port
333 second_usb_serial_enable false # This enables a second USB serial port
334 #leds_disable true # Disable using leds after config loaded
335 #play_led_disable true # Disable the play led
337 # Kill button maybe assigned to a different pin, set to the onboard pin by default
338 # See http://smoothieware.org/killbutton
339 kill_button_enable true # Set to true to enable a kill button
340 kill_button_pin 2.12 # Kill button pin. default is same as pause button 2.12 (2.11 is another good choice)
342 #msd_disable false # Disable the MSD (USB SDCARD), see http://smoothieware.org/troubleshooting#disable-msd
343 #dfu_enable false # For linux developers, set to true to enable DFU
345 # Only needed on a smoothieboard
346 # See http://smoothieware.org/currentcontrol
347 currentcontrol_module_enable true # Control stepper motor current via the configuration file
HCoop / clinton / Smoothieware.git / blob