HCoop / jackhill / qmk / firmware.git / blame
| Commit | Line | Data |
|---|---|---|
| ab4d7adb | 1 | # MCU name |
| 582a6ac7 | 2 | #MCU = at90usb1286 |
| ab4d7adb FS |
3 | MCU = atmega32u4 |
| 4 | ||
| 5 | # Processor frequency. | |
| 6 | # This will define a symbol, F_CPU, in all source code files equal to the | |
| 7 | # processor frequency in Hz. You can then use this symbol in your source code to | |
| 8 | # calculate timings. Do NOT tack on a 'UL' at the end, this will be done | |
| 9 | # automatically to create a 32-bit value in your source code. | |
| 10 | # | |
| 11 | # This will be an integer division of F_USB below, as it is sourced by | |
| 12 | # F_USB after it has run through any CPU prescalers. Note that this value | |
| 13 | # does not *change* the processor frequency - it should merely be updated to | |
| 14 | # reflect the processor speed set externally so that the code can use accurate | |
| 15 | # software delays. | |
| 16 | F_CPU = 16000000 | |
| 17 | ||
| 18 | ||
| 19 | # | |
| 20 | # LUFA specific | |
| 21 | # | |
| 22 | # Target architecture (see library "Board Types" documentation). | |
| 23 | ARCH = AVR8 | |
| 24 | ||
| 25 | # Input clock frequency. | |
| 26 | # This will define a symbol, F_USB, in all source code files equal to the | |
| 27 | # input clock frequency (before any prescaling is performed) in Hz. This value may | |
| 28 | # differ from F_CPU if prescaling is used on the latter, and is required as the | |
| 29 | # raw input clock is fed directly to the PLL sections of the AVR for high speed | |
| 30 | # clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | |
| 31 | # at the end, this will be done automatically to create a 32-bit value in your | |
| 32 | # source code. | |
| 33 | # | |
| 34 | # If no clock division is performed on the input clock inside the AVR (via the | |
| 35 | # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | |
| 36 | F_USB = $(F_CPU) | |
| 37 | ||
| 38 | # Interrupt driven control endpoint task(+60) | |
| 39 | OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT | |
| 40 | ||
| 41 | ||
| 42 | # Boot Section Size in *bytes* | |
| 43 | # Teensy halfKay 512 | |
| 44 | # Teensy++ halfKay 1024 | |
| 45 | # Atmel DFU loader 4096 | |
| 46 | # LUFA bootloader 4096 | |
| 47 | # USBaspLoader 2048 | |
| e2e387f8 | 48 | OPT_DEFS += -DBOOTLOADER_SIZE=4096 |
| ab4d7adb FS |
49 | |
| 50 | ||
| 51 | # Build Options | |
| 52 | # change yes to no to disable | |
| 53 | # | |
| e2e387f8 JH |
54 | BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000) |
| 55 | MOUSEKEY_ENABLE = yes # Mouse keys(+4700) | |
| 56 | EXTRAKEY_ENABLE = yes # Audio control and System control(+450) | |
| 57 | CONSOLE_ENABLE = yes # Console for debug(+400) | |
| 58 | COMMAND_ENABLE = yes # Commands for debug and configuration | |
| ab4d7adb | 59 | # Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE |
| e2e387f8 | 60 | SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend |
| ab4d7adb | 61 | # if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work |
| e2e387f8 JH |
62 | NKRO_ENABLE = no # USB Nkey Rollover |
| 63 | BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality on B7 by default | |
| ec266844 | 64 | RGBLIGHT_ENABLE = no # Enable keyboard RGB underglow |
| e2e387f8 JH |
65 | MIDI_ENABLE = no # MIDI support (+2400 to 4200, depending on config) |
| 66 | UNICODE_ENABLE = no # Unicode | |
| 67 | BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID | |
| 68 | AUDIO_ENABLE = no # Audio output on port C6 | |
| 69 | FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches | |
| bbea9dad | 70 | HD44780_ENABLE = no # Enable support for HD44780 based LCDs (+400) |