[jackhill/qmk/firmware.git] / keyboards / kc60 / rules.mk

# MCU name
#MCU = at90usb1287
MCU = atmega32u4

# Processor frequency.
#     This will define a symbol, F_CPU, in all source code files equal to the
#     processor frequency in Hz. You can then use this symbol in your source code to
#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
#     automatically to create a 32-bit value in your source code.
#
#     This will be an integer division of F_USB below, as it is sourced by
#     F_USB after it has run through any CPU prescalers. Note that this value
#     does not *change* the processor frequency - it should merely be updated to
#     reflect the processor speed set externally so that the code can use accurate
#     software delays.
F_CPU = 16000000


#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8

# Input clock frequency.
#     This will define a symbol, F_USB, in all source code files equal to the
#     input clock frequency (before any prescaling is performed) in Hz. This value may
#     differ from F_CPU if prescaling is used on the latter, and is required as the
#     raw input clock is fed directly to the PLL sections of the AVR for high speed
#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
#     at the end, this will be done automatically to create a 32-bit value in your
#     source code.
#
#     If no clock division is performed on the input clock inside the AVR (via the
#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)

# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT


# Boot Section Size in *bytes*
#   Teensy halfKay   512
#   Teensy++ halfKay 1024
#   Atmel DFU loader 4096
#   LUFA bootloader  4096
#   USBaspLoader     2048
OPT_DEFS += -DBOOTLOADER_SIZE=4096


# Build Options
#   change yes to no to disable
#
BOOTMAGIC_ENABLE = no       # Virtual DIP switch configuration(+1000)
MOUSEKEY_ENABLE = yes       # Mouse keys(+4700)
EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
CONSOLE_ENABLE = yes        # Console for debug(+400)
COMMAND_ENABLE = yes        # Commands for debug and configuration
KEYBOARD_LOCK_ENABLE = yes  # Allow locking of keyboard via magic key
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
SLEEP_LED_ENABLE = no       # Breathing sleep LED during USB suspend
# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
NKRO_ENABLE = no            # USB Nkey Rollover
BACKLIGHT_ENABLE = yes      # Enable keyboard backlight functionality
MIDI_ENABLE = no            # MIDI controls
UNICODE_ENABLE = no         # Unicode
BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
AUDIO_ENABLE = no           # Audio output on port C6

LAYOUTS = 60_ansi
Commit	Line	Data
44441de8 FS	1	# MCU name
	2	#MCU = at90usb1287
	3	MCU = atmega32u4
	4
	5	# Processor frequency.
	6	# This will define a symbol, F_CPU, in all source code files equal to the
	7	# processor frequency in Hz. You can then use this symbol in your source code to
	8	# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
	9	# automatically to create a 32-bit value in your source code.
	10	#
	11	# This will be an integer division of F_USB below, as it is sourced by
	12	# F_USB after it has run through any CPU prescalers. Note that this value
	13	# does not change the processor frequency - it should merely be updated to
	14	# reflect the processor speed set externally so that the code can use accurate
	15	# software delays.
	16	F_CPU = 16000000
	17
	18
	19	#
	20	# LUFA specific
	21	#
	22	# Target architecture (see library "Board Types" documentation).
	23	ARCH = AVR8
	24
	25	# Input clock frequency.
	26	# This will define a symbol, F_USB, in all source code files equal to the
	27	# input clock frequency (before any prescaling is performed) in Hz. This value may
	28	# differ from F_CPU if prescaling is used on the latter, and is required as the
	29	# raw input clock is fed directly to the PLL sections of the AVR for high speed
	30	# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
	31	# at the end, this will be done automatically to create a 32-bit value in your
	32	# source code.
	33	#
	34	# If no clock division is performed on the input clock inside the AVR (via the
	35	# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
	36	F_USB = $(F_CPU)
	37
	38	# Interrupt driven control endpoint task(+60)
	39	OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
	40
	41
	42	# Boot Section Size in bytes
	43	# Teensy halfKay 512
	44	# Teensy++ halfKay 1024
	45	# Atmel DFU loader 4096
	46	# LUFA bootloader 4096
	47	# USBaspLoader 2048
	48	OPT_DEFS += -DBOOTLOADER_SIZE=4096
	49
	50
	51	# Build Options
	52	# change yes to no to disable
	53	#
b476d65b JH	54	BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000)
	55	MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
	56	EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
	57	CONSOLE_ENABLE = yes # Console for debug(+400)
	58	COMMAND_ENABLE = yes # Commands for debug and configuration
	59	KEYBOARD_LOCK_ENABLE = yes # Allow locking of keyboard via magic key
44441de8	60	# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
b476d65b	61	SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend
44441de8	62	# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
b476d65b JH	63	NKRO_ENABLE = no # USB Nkey Rollover
	64	BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality
	65	MIDI_ENABLE = no # MIDI controls
	66	UNICODE_ENABLE = no # Unicode
	67	BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID
	68	AUDIO_ENABLE = no # Audio output on port C6
d2ff66a9 JH	69
d2ff66a9 JH	70	LAYOUTS = 60_ansi