Commit | Line | Data |
---|---|---|
81d8e6ef | 1 | # MCU name |
81d8e6ef M |
2 | MCU = atmega32u4 |
3 | ||
4 | # Processor frequency. | |
5 | # This will define a symbol, F_CPU, in all source code files equal to the | |
6 | # processor frequency in Hz. You can then use this symbol in your source code to | |
7 | # calculate timings. Do NOT tack on a 'UL' at the end, this will be done | |
8 | # automatically to create a 32-bit value in your source code. | |
9 | # | |
10 | # This will be an integer division of F_USB below, as it is sourced by | |
11 | # F_USB after it has run through any CPU prescalers. Note that this value | |
12 | # does not *change* the processor frequency - it should merely be updated to | |
13 | # reflect the processor speed set externally so that the code can use accurate | |
14 | # software delays. | |
15 | F_CPU = 16000000 | |
16 | ||
17 | ||
18 | # | |
19 | # LUFA specific | |
20 | # | |
21 | # Target architecture (see library "Board Types" documentation). | |
22 | ARCH = AVR8 | |
23 | ||
24 | # Input clock frequency. | |
25 | # This will define a symbol, F_USB, in all source code files equal to the | |
26 | # input clock frequency (before any prescaling is performed) in Hz. This value may | |
27 | # differ from F_CPU if prescaling is used on the latter, and is required as the | |
28 | # raw input clock is fed directly to the PLL sections of the AVR for high speed | |
29 | # clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | |
30 | # at the end, this will be done automatically to create a 32-bit value in your | |
31 | # source code. | |
32 | # | |
33 | # If no clock division is performed on the input clock inside the AVR (via the | |
34 | # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | |
35 | F_USB = $(F_CPU) | |
36 | ||
37 | # Interrupt driven control endpoint task(+60) | |
38 | OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT | |
39 | ||
40 | ||
41 | # Bootloader selection | |
42 | # Teensy halfkay | |
43 | # Pro Micro caterina | |
44 | # Atmel DFU atmel-dfu | |
45 | # LUFA DFU lufa-dfu | |
46 | # QMK DFU qmk-dfu | |
47 | # atmega32a bootloadHID | |
48 | BOOTLOADER = atmel-dfu | |
49 | ||
50 | ||
51 | # If you don't know the bootloader type, then you can specify the | |
52 | # Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line | |
53 | # Teensy halfKay 512 | |
54 | # Teensy++ halfKay 1024 | |
55 | # Atmel DFU loader 4096 | |
56 | # LUFA bootloader 4096 | |
57 | # USBaspLoader 2048 | |
58 | # OPT_DEFS += -DBOOTLOADER_SIZE=4096 | |
59 | ||
60 | RGB_MATRIX_ENABLE = WS2812 | |
61 | ||
62 | ||
63 | # Build Options | |
64 | # change yes to no to disable | |
65 | # | |
66 | BOOTMAGIC_ENABLE = lite # Virtual DIP switch configuration(+1000) | |
67 | MOUSEKEY_ENABLE = yes # Mouse keys(+4700) | |
68 | EXTRAKEY_ENABLE = yes # Audio control and System control(+450) | |
69 | CONSOLE_ENABLE = no # Console for debug(+400) | |
70 | COMMAND_ENABLE = no # Commands for debug and configuration | |
71 | # Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE | |
72 | SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend | |
73 | # if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work | |
74 | NKRO_ENABLE = no # USB Nkey Rollover | |
75 | BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality on B7 by default | |
76 | RGBLIGHT_ENABLE = no # Enable keyboard RGB underglow | |
77 | MIDI_ENABLE = no # MIDI support (+2400 to 4200, depending on config) | |
78 | UNICODE_ENABLE = no # Unicode | |
79 | BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID | |
80 | AUDIO_ENABLE = no # Audio output on port C6 | |
81 | FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches | |
82 | HD44780_ENABLE = no # Enable support for HD44780 based LCDs (+400) |