[jackhill/qmk/firmware.git] / keyboards / s60-x / rules.mk



# MCU name
#MCU = at90usb1287
MCU = atmega32u4

# Processor frequency.
#     This will define a symbol, F_CPU, in all source code files equal to the
#     processor frequency in Hz. You can then use this symbol in your source code to
#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
#     automatically to create a 32-bit value in your source code.
#
#     This will be an integer division of F_USB below, as it is sourced by
#     F_USB after it has run through any CPU prescalers. Note that this value
#     does not *change* the processor frequency - it should merely be updated to
#     reflect the processor speed set externally so that the code can use accurate
#     software delays.
F_CPU = 16000000


#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8

# Input clock frequency.
#     This will define a symbol, F_USB, in all source code files equal to the
#     input clock frequency (before any prescaling is performed) in Hz. This value may
#     differ from F_CPU if prescaling is used on the latter, and is required as the
#     raw input clock is fed directly to the PLL sections of the AVR for high speed
#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
#     at the end, this will be done automatically to create a 32-bit value in your
#     source code.
#
#     If no clock division is performed on the input clock inside the AVR (via the
#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)

# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT


# Boot Section Size in *bytes*
#   Teensy halfKay   512
#   Teensy++ halfKay 1024
#   Atmel DFU loader 4096
#   LUFA bootloader  4096
#   USBaspLoader     2048
OPT_DEFS += -DBOOTLOADER_SIZE=4096


# Build Options
#   change yes to no to disable
#
BOOTMAGIC_ENABLE ?= yes      # Virtual DIP switch configuration(+1000)
MOUSEKEY_ENABLE ?= yes       # Mouse keys(+4700)
EXTRAKEY_ENABLE ?= yes       # Audio control and System control(+450)
CONSOLE_ENABLE ?= yes        # Console for debug(+400)
COMMAND_ENABLE ?= yes        # Commands for debug and configuration
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
SLEEP_LED_ENABLE ?= no       # Breathing sleep LED during USB suspend
# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
NKRO_ENABLE ?= no            # USB Nkey Rollover
BACKLIGHT_ENABLE ?= no       # Enable keyboard backlight functionality on B7 by default
MIDI_ENABLE ?= no            # MIDI controls
UNICODE_ENABLE ?= no         # Unicode
BLUETOOTH_ENABLE ?= no       # Enable Bluetooth with the Adafruit EZ-Key HID
AUDIO_ENABLE ?= no           # Audio output on port C6
Commit	Line	Data
44441de8 FS	1
	2
	3	# MCU name
	4	#MCU = at90usb1287
	5	MCU = atmega32u4
	6
	7	# Processor frequency.
	8	# This will define a symbol, F_CPU, in all source code files equal to the
	9	# processor frequency in Hz. You can then use this symbol in your source code to
	10	# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
	11	# automatically to create a 32-bit value in your source code.
	12	#
	13	# This will be an integer division of F_USB below, as it is sourced by
	14	# F_USB after it has run through any CPU prescalers. Note that this value
	15	# does not change the processor frequency - it should merely be updated to
	16	# reflect the processor speed set externally so that the code can use accurate
	17	# software delays.
	18	F_CPU = 16000000
	19
	20
	21	#
	22	# LUFA specific
	23	#
	24	# Target architecture (see library "Board Types" documentation).
	25	ARCH = AVR8
	26
	27	# Input clock frequency.
	28	# This will define a symbol, F_USB, in all source code files equal to the
	29	# input clock frequency (before any prescaling is performed) in Hz. This value may
	30	# differ from F_CPU if prescaling is used on the latter, and is required as the
	31	# raw input clock is fed directly to the PLL sections of the AVR for high speed
	32	# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
	33	# at the end, this will be done automatically to create a 32-bit value in your
	34	# source code.
	35	#
	36	# If no clock division is performed on the input clock inside the AVR (via the
	37	# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
	38	F_USB = $(F_CPU)
	39
	40	# Interrupt driven control endpoint task(+60)
	41	OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
	42
	43
	44	# Boot Section Size in bytes
	45	# Teensy halfKay 512
	46	# Teensy++ halfKay 1024
	47	# Atmel DFU loader 4096
	48	# LUFA bootloader 4096
	49	# USBaspLoader 2048
	50	OPT_DEFS += -DBOOTLOADER_SIZE=4096
	51
	52
	53	# Build Options
	54	# change yes to no to disable
	55	#
	56	BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000)
	57	MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700)
	58	EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450)
	59	CONSOLE_ENABLE ?= yes # Console for debug(+400)
	60	COMMAND_ENABLE ?= yes # Commands for debug and configuration
	61	# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
	62	SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend
	63	# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
	64	NKRO_ENABLE ?= no # USB Nkey Rollover
65	BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality on B7 by default
66	MIDI_ENABLE ?= no # MIDI controls
67	UNICODE_ENABLE ?= no # Unicode
68	BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID
69	AUDIO_ENABLE ?= no # Audio output on port C6