[jackhill/qmk/firmware.git] / keyboards / preonic / rules.mk



# MCU name
#MCU = at90usb1287
MCU = atmega32u4

# Processor frequency.
#     This will define a symbol, F_CPU, in all source code files equal to the
#     processor frequency in Hz. You can then use this symbol in your source code to
#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
#     automatically to create a 32-bit value in your source code.
#
#     This will be an integer division of F_USB below, as it is sourced by
#     F_USB after it has run through any CPU prescalers. Note that this value
#     does not *change* the processor frequency - it should merely be updated to
#     reflect the processor speed set externally so that the code can use accurate
#     software delays.
F_CPU = 16000000

#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8

# Input clock frequency.
#     This will define a symbol, F_USB, in all source code files equal to the
#     input clock frequency (before any prescaling is performed) in Hz. This value may
#     differ from F_CPU if prescaling is used on the latter, and is required as the
#     raw input clock is fed directly to the PLL sections of the AVR for high speed
#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
#     at the end, this will be done automatically to create a 32-bit value in your
#     source code.
#
#     If no clock division is performed on the input clock inside the AVR (via the
#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)

# Bootloader
#     This definition is optional, and if your keyboard supports multiple bootloaders of
#     different sizes, comment this out, and the correct address will be loaded 
#     automatically (+60). See bootloader.mk for all options.
ifeq ($(strip $(KEYBOARD)), preonic/rev1)
    BOOTLOADER = atmel-dfu
endif
ifeq ($(strip $(KEYBOARD)), preonic/rev2)
    BOOTLOADER = qmk-dfu
endif

# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT

# Build Options
#   change to "no" to disable the options, or define them in the Makefile in 
#   the appropriate keymap folder that will get included automatically
#
BOOTMAGIC_ENABLE = no       # Virtual DIP switch configuration(+1000)
MOUSEKEY_ENABLE = no       # Mouse keys(+4700)
EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
CONSOLE_ENABLE = yes         # Console for debug(+400)
COMMAND_ENABLE = no        # Commands for debug and configuration
NKRO_ENABLE = no            # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
BACKLIGHT_ENABLE = yes      # Enable keyboard backlight functionality
MIDI_ENABLE = no            # MIDI controls
AUDIO_ENABLE = yes           # Audio output on port C6
UNICODE_ENABLE = no         # Unicode
BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
RGBLIGHT_ENABLE = no        # Enable WS2812 RGB underlight.
API_SYSEX_ENABLE = no

# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
SLEEP_LED_ENABLE = no    # Breathing sleep LED during USB suspend

LAYOUTS = ortho_5x12

DEFAULT_FOLDER = preonic/rev2
Commit	Line	Data
44441de8 FS	1
	2
	3	# MCU name
	4	#MCU = at90usb1287
	5	MCU = atmega32u4
	6
	7	# Processor frequency.
	8	# This will define a symbol, F_CPU, in all source code files equal to the
	9	# processor frequency in Hz. You can then use this symbol in your source code to
	10	# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
	11	# automatically to create a 32-bit value in your source code.
	12	#
	13	# This will be an integer division of F_USB below, as it is sourced by
	14	# F_USB after it has run through any CPU prescalers. Note that this value
	15	# does not change the processor frequency - it should merely be updated to
	16	# reflect the processor speed set externally so that the code can use accurate
	17	# software delays.
	18	F_CPU = 16000000
	19
	20	#
	21	# LUFA specific
	22	#
	23	# Target architecture (see library "Board Types" documentation).
	24	ARCH = AVR8
	25
	26	# Input clock frequency.
	27	# This will define a symbol, F_USB, in all source code files equal to the
	28	# input clock frequency (before any prescaling is performed) in Hz. This value may
	29	# differ from F_CPU if prescaling is used on the latter, and is required as the
	30	# raw input clock is fed directly to the PLL sections of the AVR for high speed
	31	# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
	32	# at the end, this will be done automatically to create a 32-bit value in your
	33	# source code.
	34	#
	35	# If no clock division is performed on the input clock inside the AVR (via the
	36	# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
	37	F_USB = $(F_CPU)
	38
9fdc2762 JH	39	# Bootloader
	40	# This definition is optional, and if your keyboard supports multiple bootloaders of
	41	# different sizes, comment this out, and the correct address will be loaded
	42	# automatically (+60). See bootloader.mk for all options.
	43	ifeq ($(strip $(KEYBOARD)), preonic/rev1)
	44	BOOTLOADER = atmel-dfu
	45	endif
	46	ifeq ($(strip $(KEYBOARD)), preonic/rev2)
	47	BOOTLOADER = qmk-dfu
	48	endif
	49
44441de8 FS	50	# Interrupt driven control endpoint task(+60)
	51	OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
	52
44441de8 FS	53	# Build Options
	54	# change to "no" to disable the options, or define them in the Makefile in
	55	# the appropriate keymap folder that will get included automatically
	56	#
b476d65b JH	57	BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000)
	58	MOUSEKEY_ENABLE = no # Mouse keys(+4700)
	59	EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
ec3e065f	60	CONSOLE_ENABLE = yes # Console for debug(+400)
b476d65b JH	61	COMMAND_ENABLE = no # Commands for debug and configuration
	62	NKRO_ENABLE = no # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
	63	BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality
5ffec5d9	64	MIDI_ENABLE = no # MIDI controls
b476d65b JH	65	AUDIO_ENABLE = yes # Audio output on port C6
	66	UNICODE_ENABLE = no # Unicode
	67	BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID
	68	RGBLIGHT_ENABLE = no # Enable WS2812 RGB underlight.
	69	API_SYSEX_ENABLE = no
44441de8 FS	70
44441de8 FS	71	# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
d2ff66a9 JH	72	SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend
d2ff66a9 JH	73
ec3e065f JH	74	LAYOUTS = ortho_5x12
	75
	76	DEFAULT_FOLDER = preonic/rev2