[jackhill/qmk/firmware.git] / keyboards / ok60 / rules.mk

# MCU name
MCU = atmega32u4

# Processor frequency.
#     This will define a symbol, F_CPU, in all source code files equal to the
#     processor frequency in Hz. You can then use this symbol in your source code to
#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
#     automatically to create a 32-bit value in your source code.
#
#     This will be an integer division of F_USB below, as it is sourced by
#     F_USB after it has run through any CPU prescalers. Note that this value
#     does not *change* the processor frequency - it should merely be updated to
#     reflect the processor speed set externally so that the code can use accurate
#     software delays.
F_CPU = 16000000


#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8

# Input clock frequency.
#     This will define a symbol, F_USB, in all source code files equal to the
#     input clock frequency (before any prescaling is performed) in Hz. This value may
#     differ from F_CPU if prescaling is used on the latter, and is required as the
#     raw input clock is fed directly to the PLL sections of the AVR for high speed
#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
#     at the end, this will be done automatically to create a 32-bit value in your
#     source code.
#
#     If no clock division is performed on the input clock inside the AVR (via the
#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)

# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT


# Boot Section Size in *bytes*
#   Teensy halfKay   512
#   Teensy++ halfKay 1024
#   Atmel DFU loader 4096
#   LUFA bootloader  4096
#   USBaspLoader     2048
OPT_DEFS += -DBOOTLOADER_SIZE=4096


# Build Options
#   comment out to disable the options.
#
BOOTMAGIC_ENABLE = yes		# Virtual DIP switch configuration(+1000)
MOUSEKEY_ENABLE = yes		# Mouse keys(+4700)
EXTRAKEY_ENABLE = yes		# Audio control and System control(+450)
# CONSOLE_ENABLE = yes		# Console for debug(+400)
# COMMAND_ENABLE = yes		# Commands for debug and configuration
KEYBOARD_LOCK_ENABLE = yes	# Allow locking of keyboard via magic key
NKRO_ENABLE = yes			# USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
BACKLIGHT_ENABLE = yes	# Enable keyboard backlight functionality
RGBLIGHT_ENABLE = yes  # Enable the RGB backlight
# MIDI_ENABLE = YES			# MIDI controls
# UNICODE_ENABLE = YES		# Unicode
# BLUETOOTH_ENABLE = yes	# Enable Bluetooth with the Adafruit EZ-Key HID

LAYOUTS = 60_ansi 60_iso 60_hhkb
Commit	Line	Data
eba4b08a	1	# MCU name
	2	MCU = atmega32u4
	3
	4	# Processor frequency.
	5	# This will define a symbol, F_CPU, in all source code files equal to the
	6	# processor frequency in Hz. You can then use this symbol in your source code to
	7	# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
	8	# automatically to create a 32-bit value in your source code.
	9	#
	10	# This will be an integer division of F_USB below, as it is sourced by
	11	# F_USB after it has run through any CPU prescalers. Note that this value
	12	# does not change the processor frequency - it should merely be updated to
	13	# reflect the processor speed set externally so that the code can use accurate
	14	# software delays.
	15	F_CPU = 16000000
	16
	17
	18	#
	19	# LUFA specific
	20	#
	21	# Target architecture (see library "Board Types" documentation).
	22	ARCH = AVR8
	23
	24	# Input clock frequency.
	25	# This will define a symbol, F_USB, in all source code files equal to the
	26	# input clock frequency (before any prescaling is performed) in Hz. This value may
	27	# differ from F_CPU if prescaling is used on the latter, and is required as the
	28	# raw input clock is fed directly to the PLL sections of the AVR for high speed
	29	# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
	30	# at the end, this will be done automatically to create a 32-bit value in your
	31	# source code.
	32	#
	33	# If no clock division is performed on the input clock inside the AVR (via the
	34	# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
	35	F_USB = $(F_CPU)
	36
	37	# Interrupt driven control endpoint task(+60)
	38	OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
	39
	40
	41	# Boot Section Size in bytes
	42	# Teensy halfKay 512
	43	# Teensy++ halfKay 1024
	44	# Atmel DFU loader 4096
	45	# LUFA bootloader 4096
	46	# USBaspLoader 2048
	47	OPT_DEFS += -DBOOTLOADER_SIZE=4096
	48
	49
	50	# Build Options
	51	# comment out to disable the options.
	52	#
	53	BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
	54	MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
	55	EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
	56	# CONSOLE_ENABLE = yes # Console for debug(+400)
	57	# COMMAND_ENABLE = yes # Commands for debug and configuration
	58	KEYBOARD_LOCK_ENABLE = yes # Allow locking of keyboard via magic key
	59	NKRO_ENABLE = yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
	60	BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality
	61	RGBLIGHT_ENABLE = yes # Enable the RGB backlight
	62	# MIDI_ENABLE = YES # MIDI controls
	63	# UNICODE_ENABLE = YES # Unicode
	64	# BLUETOOTH_ENABLE = yes # Enable Bluetooth with the Adafruit EZ-Key HID
65
54517f8b	66	LAYOUTS = 60_ansi 60_iso 60_hhkb