Commit | Line | Data |
---|---|---|
015aed50 M |
1 | # MCU name |
2 | #MCU = at90usb1286 | |
3 | MCU = atmega32u4 | |
4 | ||
5 | # Processor frequency. | |
6 | # This will define a symbol, F_CPU, in all source code files equal to the | |
7 | # processor frequency in Hz. You can then use this symbol in your source code to | |
8 | # calculate timings. Do NOT tack on a 'UL' at the end, this will be done | |
9 | # automatically to create a 32-bit value in your source code. | |
10 | # | |
11 | # This will be an integer division of F_USB below, as it is sourced by | |
12 | # F_USB after it has run through any CPU prescalers. Note that this value | |
13 | # does not *change* the processor frequency - it should merely be updated to | |
14 | # reflect the processor speed set externally so that the code can use accurate | |
15 | # software delays. | |
16 | F_CPU = 16000000 | |
17 | ||
18 | ||
19 | # | |
20 | # LUFA specific | |
21 | # | |
22 | # Target architecture (see library "Board Types" documentation). | |
23 | ARCH = AVR8 | |
24 | ||
25 | # Input clock frequency. | |
26 | # This will define a symbol, F_USB, in all source code files equal to the | |
27 | # input clock frequency (before any prescaling is performed) in Hz. This value may | |
28 | # differ from F_CPU if prescaling is used on the latter, and is required as the | |
29 | # raw input clock is fed directly to the PLL sections of the AVR for high speed | |
30 | # clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | |
31 | # at the end, this will be done automatically to create a 32-bit value in your | |
32 | # source code. | |
33 | # | |
34 | # If no clock division is performed on the input clock inside the AVR (via the | |
35 | # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | |
36 | F_USB = $(F_CPU) | |
37 | ||
38 | # Interrupt driven control endpoint task(+60) | |
39 | OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT | |
40 | ||
41 | ||
42 | # Boot Section Size in *bytes* | |
43 | # Teensy halfKay 512 | |
44 | # Teensy++ halfKay 1024 | |
45 | # Atmel DFU loader 4096 | |
46 | # LUFA bootloader 4096 | |
47 | # USBaspLoader 2048 | |
48 | OPT_DEFS += -DBOOTLOADER_SIZE=4096 | |
49 | ||
50 | ||
51 | # Build Options | |
52 | # change yes to no to disable | |
53 | # | |
54 | BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000) | |
55 | MOUSEKEY_ENABLE = yes # Mouse keys(+4700) | |
56 | EXTRAKEY_ENABLE = yes # Audio control and System control(+450) | |
57 | CONSOLE_ENABLE = yes # Console for debug(+400) | |
356fe590 | 58 | COMMAND_ENABLE = no # Commands for debug and configuration |
015aed50 M |
59 | # Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE |
60 | SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend | |
61 | # if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work | |
62 | NKRO_ENABLE ?= yes # USB Nkey Rollover | |
356fe590 | 63 | BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality on B7 by default |
015aed50 M |
64 | RGBLIGHT_ENABLE = yes |
65 | MIDI_ENABLE = no # MIDI support (+2400 to 4200, depending on config) | |
66 | UNICODE_ENABLE = no # Unicode | |
67 | BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID | |
68 | AUDIO_ENABLE = no # Audio output on port C6 | |
69 | FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches | |
70 | ||
71 | CUSTOM_MATRIX = yes | |
72 | SRC += matrix.c |