HCoop / jackhill / qmk / firmware.git / blame
| Commit | Line | Data |
|---|---|---|
| 66ef1e3d | 1 | # project specific files |
| 2dea540a W |
2 | SRC = ../zeal60/zeal60.c \ |
| 3 | ../zeal60/rgb_backlight.c \ | |
| 66ef1e3d W |
4 | quantum/color.c \ |
| 5 | drivers/issi/is31fl3218.c \ | |
| 6 | drivers/avr/i2c_master.c | |
| 7 | ||
| 8 | ||
| 9 | # MCU name | |
| 10 | MCU = atmega32u4 | |
| 11 | ||
| 12 | # Processor frequency. | |
| 13 | # This will define a symbol, F_CPU, in all source code files equal to the | |
| 14 | # processor frequency in Hz. You can then use this symbol in your source code to | |
| 15 | # calculate timings. Do NOT tack on a 'UL' at the end, this will be done | |
| 16 | # automatically to create a 32-bit value in your source code. | |
| 17 | # | |
| 18 | # This will be an integer division of F_USB below, as it is sourced by | |
| 19 | # F_USB after it has run through any CPU prescalers. Note that this value | |
| 20 | # does not *change* the processor frequency - it should merely be updated to | |
| 21 | # reflect the processor speed set externally so that the code can use accurate | |
| 22 | # software delays. | |
| 23 | F_CPU = 16000000 | |
| 24 | ||
| 25 | ||
| 26 | # | |
| 27 | # LUFA specific | |
| 28 | # | |
| 29 | # Target architecture (see library "Board Types" documentation). | |
| 30 | ARCH = AVR8 | |
| 31 | ||
| 32 | # Input clock frequency. | |
| 33 | # This will define a symbol, F_USB, in all source code files equal to the | |
| 34 | # input clock frequency (before any prescaling is performed) in Hz. This value may | |
| 35 | # differ from F_CPU if prescaling is used on the latter, and is required as the | |
| 36 | # raw input clock is fed directly to the PLL sections of the AVR for high speed | |
| 37 | # clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | |
| 38 | # at the end, this will be done automatically to create a 32-bit value in your | |
| 39 | # source code. | |
| 40 | # | |
| 41 | # If no clock division is performed on the input clock inside the AVR (via the | |
| 42 | # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | |
| 43 | F_USB = $(F_CPU) | |
| 44 | ||
| 45 | # Interrupt driven control endpoint task(+60) | |
| 46 | OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT | |
| 47 | ||
| 48 | # Boot Section | |
| 49 | BOOTLOADER = atmel-dfu | |
| 50 | ||
| 51 | # Do not put the microcontroller into power saving mode | |
| 52 | # when we get USB suspend event. We want it to keep updating | |
| 53 | # backlight effects. | |
| 54 | OPT_DEFS += -DNO_SUSPEND_POWER_DOWN | |
| 55 | ||
| 56 | ||
| 57 | # Build Options | |
| 58 | # change yes to no to disable | |
| 59 | # | |
| 2dea540a | 60 | BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000) |
| 66ef1e3d W |
61 | MOUSEKEY_ENABLE = no # Mouse keys(+4700) |
| 62 | EXTRAKEY_ENABLE = yes # Audio control and System control(+450) | |
| 2dea540a | 63 | CONSOLE_ENABLE = no # Console for debug(+400) |
| 66ef1e3d | 64 | COMMAND_ENABLE = no # Commands for debug and configuration |
| 2dea540a W |
65 | NKRO_ENABLE = yes # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work |
| 66 | BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality | |
| 67 | MIDI_ENABLE = no # MIDI controls | |
| 68 | AUDIO_ENABLE = no # Audio output on port C6 | |
| 66ef1e3d W |
69 | UNICODE_ENABLE = no # Unicode |
| 70 | BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID | |
| 2dea540a W |
71 | RGBLIGHT_ENABLE = no # Enable WS2812 RGB underlight. Do not enable this with audio at the same time. |
| 72 | ||
| 73 | # Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE | |
| 74 | SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend | |
| 66ef1e3d W |
75 | |
| 76 | RAW_ENABLE = yes | |
| 77 | DYNAMIC_KEYMAP_ENABLE = yes | |
| 78 | CIE1931_CURVE = yes | |
| 2dea540a | 79 |