| 99da48c7 |
1 | SRC += i2c.c \ |
| 2 | serial.c \ |
| 3 | matrix.c \ |
| 4 | split_util.c \ |
| 5 | |
| 6 | # MCU name |
| 7 | #MCU = at90usb1286 |
| 8 | MCU = atmega32u4 |
| 9 | |
| 10 | # Processor frequency. |
| 11 | # This will define a symbol, F_CPU, in all source code files equal to the |
| 12 | # processor frequency in Hz. You can then use this symbol in your source code to |
| 13 | # calculate timings. Do NOT tack on a 'UL' at the end, this will be done |
| 14 | # automatically to create a 32-bit value in your source code. |
| 15 | # |
| 16 | # This will be an integer division of F_USB below, as it is sourced by |
| 17 | # F_USB after it has run through any CPU prescalers. Note that this value |
| 18 | # does not *change* the processor frequency - it should merely be updated to |
| 19 | # reflect the processor speed set externally so that the code can use accurate |
| 20 | # software delays. |
| 21 | F_CPU = 16000000 |
| 22 | |
| 23 | |
| 24 | # |
| 25 | # LUFA specific |
| 26 | # |
| 27 | # Target architecture (see library "Board Types" documentation). |
| 28 | ARCH = AVR8 |
| 29 | |
| 30 | # Input clock frequency. |
| 31 | # This will define a symbol, F_USB, in all source code files equal to the |
| 32 | # input clock frequency (before any prescaling is performed) in Hz. This value may |
| 33 | # differ from F_CPU if prescaling is used on the latter, and is required as the |
| 34 | # raw input clock is fed directly to the PLL sections of the AVR for high speed |
| 35 | # clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' |
| 36 | # at the end, this will be done automatically to create a 32-bit value in your |
| 37 | # source code. |
| 38 | # |
| 39 | # If no clock division is performed on the input clock inside the AVR (via the |
| 40 | # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. |
| 41 | F_USB = $(F_CPU) |
| 42 | |
| 43 | # Interrupt driven control endpoint task(+60) |
| 44 | OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT |
| 45 | |
| 46 | |
| 47 | # Boot Section Size in *bytes* |
| 48 | # Teensy halfKay 512 |
| 49 | # Teensy++ halfKay 1024 |
| 50 | # Atmel DFU loader 4096 |
| 51 | # LUFA bootloader 4096 |
| 52 | # USBaspLoader 2048 |
| 53 | OPT_DEFS += -DBOOTLOADER_SIZE=4096 |
| 54 | |
| 55 | |
| 56 | # Build Options |
| 57 | # change yes to no to disable |
| 58 | # |
| 59 | BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000) |
| 60 | MOUSEKEY_ENABLE = no # Mouse keys(+4700) |
| 61 | EXTRAKEY_ENABLE = no # Audio control and System control(+450) |
| 62 | CONSOLE_ENABLE = no # Console for debug(+400) |
| 63 | COMMAND_ENABLE = no # Commands for debug and configuration |
| 64 | # Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE |
| 65 | SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend |
| 66 | # if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work |
| 67 | NKRO_ENABLE = no # USB Nkey Rollover |
| 68 | BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality on B7 by default |
| 69 | MIDI_ENABLE = no # MIDI support (+2400 to 4200, depending on config) |
| 70 | UNICODE_ENABLE = no # Unicode |
| 71 | BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID |
| 72 | AUDIO_ENABLE = no # Audio output on port C6 |
| 73 | FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches |
| 74 | HD44780_ENABLE = no # Enable support for HD44780 based LCDs (+400) |
| 75 | |
| 76 | CUSTOM_MATRIX = yes |
| 77 | USE_I2C = yes |
| 00b6f148 |
78 | RGBLIGHT_ENABLE = yes # Enable WS2812 RGB underlight. |
HCoop / jackhill / qmk / firmware.git / blame