[jackhill/qmk/firmware.git] / keyboards / fourier / rules.mk

SRC += matrix.c \
	   i2c.c \
	   split_util.c \
	   serial.c

# MCU name
#MCU = at90usb1287
MCU = atmega32u4

# Processor frequency.
#     This will define a symbol, F_CPU, in all source code files equal to the
#     processor frequency in Hz. You can then use this symbol in your source code to
#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
#     automatically to create a 32-bit value in your source code.
#
#     This will be an integer division of F_USB below, as it is sourced by
#     F_USB after it has run through any CPU prescalers. Note that this value
#     does not *change* the processor frequency - it should merely be updated to
#     reflect the processor speed set externally so that the code can use accurate
#     software delays.
F_CPU = 16000000

#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8

# Input clock frequency.
#     This will define a symbol, F_USB, in all source code files equal to the
#     input clock frequency (before any prescaling is performed) in Hz. This value may
#     differ from F_CPU if prescaling is used on the latter, and is required as the
#     raw input clock is fed directly to the PLL sections of the AVR for high speed
#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
#     at the end, this will be done automatically to create a 32-bit value in your
#     source code.
#
#     If no clock division is performed on the input clock inside the AVR (via the
#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)

# Bootloader
#     This definition is optional, and if your keyboard supports multiple bootloaders of
#     different sizes, comment this out, and the correct address will be loaded 
#     automatically (+60). See bootloader.mk for all options.
BOOTLOADER = caterina

# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT

# Build Options
#   change to "no" to disable the options, or define them in the Makefile in
#   the appropriate keymap folder that will get included automatically
#
BOOTMAGIC_ENABLE = no       # Virtual DIP switch configuration(+1000)
MOUSEKEY_ENABLE = no        # Mouse keys(+4700)
EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
CONSOLE_ENABLE = no         # Console for debug(+400)
COMMAND_ENABLE = yes        # Commands for debug and configuration
NKRO_ENABLE = no            # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
BACKLIGHT_ENABLE = no       # Enable keyboard backlight functionality
MIDI_ENABLE = no            # MIDI controls
AUDIO_ENABLE = no           # Audio output on port C6
UNICODE_ENABLE = no         # Unicode
BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
RGBLIGHT_ENABLE = yes        # Enable WS2812 RGB underlight. 
SUBPROJECT_rev1 = yes
USE_I2C = yes
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
SLEEP_LED_ENABLE = no    # Breathing sleep LED during USB suspend

CUSTOM_MATRIX = yes

DEFAULT_FOLDER = fourier/rev1
Commit	Line	Data
4e92dcee D	1	SRC += matrix.c \
	2	i2c.c \
	3	split_util.c \
	4	serial.c
	5
	6	# MCU name
	7	#MCU = at90usb1287
	8	MCU = atmega32u4
	9
	10	# Processor frequency.
	11	# This will define a symbol, F_CPU, in all source code files equal to the
	12	# processor frequency in Hz. You can then use this symbol in your source code to
	13	# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
	14	# automatically to create a 32-bit value in your source code.
	15	#
	16	# This will be an integer division of F_USB below, as it is sourced by
	17	# F_USB after it has run through any CPU prescalers. Note that this value
	18	# does not change the processor frequency - it should merely be updated to
	19	# reflect the processor speed set externally so that the code can use accurate
	20	# software delays.
	21	F_CPU = 16000000
	22
	23	#
	24	# LUFA specific
	25	#
	26	# Target architecture (see library "Board Types" documentation).
	27	ARCH = AVR8
	28
	29	# Input clock frequency.
	30	# This will define a symbol, F_USB, in all source code files equal to the
	31	# input clock frequency (before any prescaling is performed) in Hz. This value may
	32	# differ from F_CPU if prescaling is used on the latter, and is required as the
	33	# raw input clock is fed directly to the PLL sections of the AVR for high speed
	34	# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
	35	# at the end, this will be done automatically to create a 32-bit value in your
	36	# source code.
	37	#
	38	# If no clock division is performed on the input clock inside the AVR (via the
	39	# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
	40	F_USB = $(F_CPU)
	41
	42	# Bootloader
	43	# This definition is optional, and if your keyboard supports multiple bootloaders of
	44	# different sizes, comment this out, and the correct address will be loaded
	45	# automatically (+60). See bootloader.mk for all options.
	46	BOOTLOADER = caterina
	47
	48	# Interrupt driven control endpoint task(+60)
	49	OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
	50
	51	# Build Options
	52	# change to "no" to disable the options, or define them in the Makefile in
	53	# the appropriate keymap folder that will get included automatically
	54	#
	55	BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000)
	56	MOUSEKEY_ENABLE = no # Mouse keys(+4700)
	57	EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
	58	CONSOLE_ENABLE = no # Console for debug(+400)
	59	COMMAND_ENABLE = yes # Commands for debug and configuration
	60	NKRO_ENABLE = no # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
	61	BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality
	62	MIDI_ENABLE = no # MIDI controls
	63	AUDIO_ENABLE = no # Audio output on port C6
	64	UNICODE_ENABLE = no # Unicode
65	BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID
00b6f148	66	RGBLIGHT_ENABLE = yes # Enable WS2812 RGB underlight.
4e92dcee D	67	SUBPROJECT_rev1 = yes
	68	USE_I2C = yes
	69	# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
	70	SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend
	71
	72	CUSTOM_MATRIX = yes
	73
	74	DEFAULT_FOLDER = fourier/rev1