HCoop / jackhill / qmk / firmware.git / blame
| Commit | Line | Data |
|---|---|---|
| b73adf0d DS |
1 | # MCU name |
| 2 | MCU = atmega32u2 | |
| 3 | ||
| 4 | # Processor frequency. | |
| 5 | # This will define a symbol, F_CPU, in all source code files equal to the | |
| 6 | # processor frequency in Hz. You can then use this symbol in your source code to | |
| 7 | # calculate timings. Do NOT tack on a 'UL' at the end, this will be done | |
| 8 | # automatically to create a 32-bit value in your source code. | |
| 9 | # | |
| 10 | # This will be an integer division of F_USB below, as it is sourced by | |
| 11 | # F_USB after it has run through any CPU prescalers. Note that this value | |
| 12 | # does not *change* the processor frequency - it should merely be updated to | |
| 13 | # reflect the processor speed set externally so that the code can use accurate | |
| 14 | # software delays. | |
| 15 | F_CPU = 16000000 | |
| 16 | ||
| 17 | # | |
| 18 | # LUFA specific | |
| 19 | # | |
| 20 | # Target architecture (see library "Board Types" documentation). | |
| 21 | ARCH = AVR8 | |
| 22 | ||
| 23 | # Input clock frequency. | |
| 24 | # This will define a symbol, F_USB, in all source code files equal to the | |
| 25 | # input clock frequency (before any prescaling is performed) in Hz. This value may | |
| 26 | # differ from F_CPU if prescaling is used on the latter, and is required as the | |
| 27 | # raw input clock is fed directly to the PLL sections of the AVR for high speed | |
| 28 | # clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | |
| 29 | # at the end, this will be done automatically to create a 32-bit value in your | |
| 30 | # source code. | |
| 31 | # | |
| 32 | # If no clock division is performed on the input clock inside the AVR (via the | |
| 33 | # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | |
| 34 | F_USB = $(F_CPU) | |
| 35 | ||
| 36 | # Interrupt driven control endpoint task(+60) | |
| 37 | OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT | |
| 38 | ||
| 39 | ||
| 40 | # Boot Section Size in *bytes* | |
| 41 | # Teensy halfKay 512 | |
| 42 | # Teensy++ halfKay 1024 | |
| 43 | # Atmel DFU loader 4096 | |
| 44 | # LUFA bootloader 4096 | |
| 45 | # USBaspLoader 2048 | |
| 46 | OPT_DEFS += -DBOOTLOADER_SIZE=4096 | |
| 47 | ||
| 48 | ||
| 49 | # Build Options | |
| 50 | # change yes to no to disable | |
| 51 | # | |
| b476d65b JH |
52 | BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000) |
| 53 | MOUSEKEY_ENABLE = yes # Mouse keys(+4700) | |
| 54 | EXTRAKEY_ENABLE = yes # Audio control and System control(+450) | |
| 55 | CONSOLE_ENABLE = yes # Console for debug(+400) | |
| 56 | COMMAND_ENABLE = yes # Commands for debug and configuration | |
| 57 | NKRO_ENABLE = no # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work | |
| 58 | BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality | |
| 59 | MIDI_ENABLE = no # MIDI controls | |
| 60 | AUDIO_ENABLE = no # Audio output on port C6 | |
| 61 | UNICODE_ENABLE = no # Unicode | |
| 62 | BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID | |
| 00b6f148 | 63 | RGBLIGHT_ENABLE = no # Enable WS2812 RGB underlight. |
| b73adf0d DS |
64 | |
| 65 | ||
| b476d65b | 66 | CUSTOM_MATRIX = yes |
| b73adf0d | 67 | SRC = matrix.c |