// PRUSA iteration3
// Z axis
// GNU GPL v3
// Josef Průša <josefprusa@me.com>
// Václav 'ax' Hůla <axtheb@gmail.com>
// http://www.reprap.org/wiki/Prusa_Mendel
// http://github.com/prusajr/PrusaMendel

include <configuration.scad>

module zmotorholder(thickness=20, bottom_thickness=5){
    difference(){
        union(){
            // Motor holding part
            difference(){
                union(){
                    zrodholder(thickness=thickness, xlen=45, ylen=45);
                    translate([board_to_xz_distance, board_to_xz_distance, 0]) {
                        nema17(places=[0, 1, 1, 1], h=bottom_thickness + layer_height);
                    }
                }

                // motor screw holes
                translate([board_to_xz_distance, board_to_xz_distance, thickness]) {
                    mirror([0, 0, 1]) translate([0, 0, thickness-8])
                        nema17(places=[0, 1, 1, 1], holes=true, h=bottom_thickness + 1, shadow=5);
                }
            }
        }
    }
}


module zrodholder(thickness=14, bottom_thickness=5, ylen=42, xlen=34){
    difference(){
        union(){
            difference(){
                union(){
                    //piece along the flat side of a board
                    cube_fillet([14, ylen, bottom_thickness], vertical=[3, 3, 0, 0]);
                    cube_fillet([5, ylen, thickness], vertical=[3, 3, 0, 0], top = [thickness/1.5, 0, 0, 5]);
                    //hole for Z axis is thru this
                    cube_fillet([xlen, 14, bottom_thickness], vertical=[0, 0, 0, 3]);
                    //piece along cut side of the board
                    if (i_am_box == 1) {
                        translate([-board_thickness, 0, 0]) cube_fillet([board_thickness + board_to_xz_distance, 5, thickness], radius=2, top = [0, 0, 0, thickness]);
                    } else {
                        translate([-board_thickness/2, 0, 0]) cube_fillet([board_thickness/2 + board_to_xz_distance+5, 5, thickness], radius=2, top = [0, 0, 0, thickness]);
                    }
                    //smooth rod insert
                    translate([board_to_xz_distance, 9, 0]) intersection() {
                        cylinder(h=bottom_thickness + layer_height, r=(bushing_z[0] + 5 * single_wall_width));
                        if (bushing_z[0] < 5) {
                            translate([0, -5 , bottom_thickness / 2]) cube([20, 20, bottom_thickness + 10], center=true);
                        } else {
                            translate([0, -bushing_z[0], bottom_thickness / 2]) cube([bushing_z[0] * 4, bushing_z[0] * 4, bottom_thickness + 10], center=true);
                        }
                    }
                }
                //smooth rod hole
                translate([board_to_xz_distance, 9, -1]) cylinder(h=board_thickness+2, r=(bushing_z[0]));
                // cutout
                translate([board_to_xz_distance-1, 5+(bushing_z[0]), 0.4]) cube([2, 10, 100]);
                //inside rouned corner
                translate([0, 5, -1]) cylinder(r=1.2, h=100, $fn=8);
                //side screw
                //translate([-board_thickness/2, 0, thickness/2-1.5]) rotate([-90, 0, 0]) screw(h=30, r_head=4);
                //front screws
                if (i_am_box != 1) {
                    //single plate has both screws on front
                    translate([17, 35.5, bottom_thickness+4]) rotate([0, -90, 0]) {
                        screw(head_drop=12, h=122, r_head=4);
                    }
                    translate([17, 15.5, bottom_thickness+4]) rotate([0, -90, 0]) {
                        screw(head_drop=12, h=122, r_head=4);
                    }
                } else {
                    translate([17, 30, bottom_thickness+4]) rotate([0, -90, 0]) {
                        screw(head_drop=12, h=122, r_head=4);
                    }
                    //side screw
                    translate([-board_thickness/2, 0, thickness/2]) rotate([-90, 0, 0]) screw(h=30, r_head=4);
                }
            }
        }
    }
}

translate([0, -2, 0]) mirror([0, 1, 0]) zmotorholder();
translate([0, 2, 0]) zmotorholder();

translate([21, -62, 0]) zrodholder();
translate([20, 62, 0]) mirror([0, 1, 0]) zrodholder();