Victor Bolshakov [Tue, 21 Feb 2017 19:29:53 +0000 (22:29 +0300)]
Revert DEBUG format once again
Victor Bolshakov [Tue, 21 Feb 2017 17:53:16 +0000 (20:53 +0300)]
Added human redable format of current grid display
Victor Bolshakov [Tue, 21 Feb 2017 17:47:44 +0000 (20:47 +0300)]
Added leveling region definition using start point and x and y size
Jim Morris [Tue, 21 Feb 2017 05:09:59 +0000 (21:09 -0800)]
Merge pull request #1132 from wolfmanjm/upstreamedge
revert
c10aa2c8c4e34fd77734da623d4022e680856760
Jim Morris [Tue, 21 Feb 2017 05:08:35 +0000 (21:08 -0800)]
Jim Morris [Tue, 21 Feb 2017 02:19:41 +0000 (18:19 -0800)]
Update PULL_REQUEST_TEMPLATE.md
Jim Morris [Tue, 21 Feb 2017 02:10:01 +0000 (18:10 -0800)]
Merge pull request #1131 from wolfmanjm/upstreamedge
Fix a bug where very slow feedrates could cause the step rate to be less than the stepticker period.
Jim Morris [Tue, 21 Feb 2017 02:05:46 +0000 (18:05 -0800)]
Fix a bug where very slow feedrates could cause the step rate to be less than the stepticker period.
Potential fix used here is to make sure that the minimum ticks for acceleration is 1. Not sure if that may have consequences.
This showed up as a problem doing G1 X1 F1 where it would step at high rates and finish immediately
Jim Morris [Tue, 21 Feb 2017 00:30:32 +0000 (16:30 -0800)]
remove block debug
Jim Morris [Tue, 21 Feb 2017 00:30:01 +0000 (16:30 -0800)]
more debug stuff
Jim Morris [Mon, 20 Feb 2017 23:37:00 +0000 (15:37 -0800)]
Merge branch 'upstreamedge' into stepticker/use-64bit-fixed-point
Jim Morris [Mon, 20 Feb 2017 23:36:43 +0000 (15:36 -0800)]
add some more block debugging
Jim Morris [Mon, 20 Feb 2017 22:32:35 +0000 (14:32 -0800)]
Merge branch 'upstreamedge' into stepticker/use-64bit-fixed-point
Jim Morris [Mon, 20 Feb 2017 22:32:20 +0000 (14:32 -0800)]
Merge remote-tracking branch 'upstream/edge' into upstreamedge
Jim Morris [Mon, 20 Feb 2017 22:31:25 +0000 (14:31 -0800)]
Allow larger strings for M114 and get pos
check for sane values of number of axis
Jim Morris [Mon, 20 Feb 2017 21:41:47 +0000 (13:41 -0800)]
Merge pull request #1129 from wolfmanjm/upstreamedge
make default for get_axis size 3 not n_primary_axis
Jim Morris [Mon, 20 Feb 2017 21:07:31 +0000 (13:07 -0800)]
make default for get_axis size 3 not n_primary_axis
Victor Bolshakov [Mon, 20 Feb 2017 13:54:03 +0000 (16:54 +0300)]
Merge branch 'edge' of https://github.com/vbolshakov/Smoothieware; branch 'edge' of https://github.com/Smoothieware/Smoothieware into edge
Victor Bolshakov [Mon, 20 Feb 2017 13:46:50 +0000 (16:46 +0300)]
Revert back coordinates format in DEBUG messages
Jim Morris [Sat, 18 Feb 2017 20:36:03 +0000 (12:36 -0800)]
add hores build
Jim Morris [Sat, 18 Feb 2017 20:28:13 +0000 (12:28 -0800)]
Add prebuild binary for hires
Jim Morris [Sat, 18 Feb 2017 20:21:18 +0000 (12:21 -0800)]
Merge remote-tracking branch 'upstream/edge' into stepticker/use-64bit-fixed-point
Victor Bolshakov [Sat, 18 Feb 2017 13:34:19 +0000 (16:34 +0300)]
Start probing from (0;0) by removing navigation to bottom right corner left from DeltaGrid
Victor Bolshakov [Fri, 17 Feb 2017 08:02:24 +0000 (11:02 +0300)]
Wor If current grid size NxM less or equal to configured.
Arthur Wolf [Thu, 16 Feb 2017 13:59:02 +0000 (14:59 +0100)]
Merge pull request #1125 from Smoothieware/code-of-conduct
Stating the obvious : creating a code of conduct.
Arthur Wolf [Wed, 15 Feb 2017 22:44:47 +0000 (23:44 +0100)]
Stating the obvious : creating a code of conduct.
This is something that can be pointed at when people cross the line as happens sometimes. It might be useful to *some* people for who this isn't obvious, though I doubt it.
Victor Bolshakov [Wed, 15 Feb 2017 18:29:10 +0000 (21:29 +0300)]
Typos fixed
Victor Bolshakov [Wed, 15 Feb 2017 17:55:38 +0000 (20:55 +0300)]
revert .gitignore
Victor Bolshakov [Wed, 15 Feb 2017 10:33:55 +0000 (13:33 +0300)]
Compact grid sizes into struct
Victor Bolshakov [Wed, 15 Feb 2017 10:25:45 +0000 (13:25 +0300)]
G28 default grid size from configuration. Error messages for bigger that configured grid sizes.
Victor Bolshakov [Tue, 14 Feb 2017 19:39:03 +0000 (22:39 +0300)]
Fix save and load to/from file
Victor Bolshakov [Tue, 14 Feb 2017 19:17:52 +0000 (22:17 +0300)]
Compatibility fix
Victor Bolshakov [Tue, 14 Feb 2017 10:18:32 +0000 (13:18 +0300)]
Grid size on the fly
Victor Bolshakov [Tue, 14 Feb 2017 10:15:25 +0000 (13:15 +0300)]
Grid size on the fly
Jim Morris [Mon, 13 Feb 2017 23:06:17 +0000 (15:06 -0800)]
Merge pull request #1123 from wolfmanjm/upstreamedge
allow rectangular grid to use G32 as well as G31
Jim Morris [Mon, 13 Feb 2017 23:05:20 +0000 (15:05 -0800)]
allow rectangular grid to use G32 as well as G31
Jim Morris [Sat, 11 Feb 2017 18:44:40 +0000 (10:44 -0800)]
Update CartGridStrategy.cpp
Jim Morris [Sat, 11 Feb 2017 18:43:06 +0000 (10:43 -0800)]
Merge pull request #1121 from wolfmanjm/upstreamedge
remove extrapolation
Jim Morris [Sat, 11 Feb 2017 18:41:24 +0000 (10:41 -0800)]
remove unused rotuiens in cart grid
Jim Morris [Sat, 11 Feb 2017 18:39:35 +0000 (10:39 -0800)]
Merge remote-tracking branch 'upstream/edge' into upstreamedge
Jim Morris [Sat, 11 Feb 2017 18:39:08 +0000 (10:39 -0800)]
remove uneeded routine in cart grid
Jim Morris [Sat, 11 Feb 2017 18:38:26 +0000 (10:38 -0800)]
Merge pull request #1120 from lordofhyphens/cart-grid
Fix compensation to work over entire positive X,Y
Joseph Lenox [Sat, 11 Feb 2017 18:33:13 +0000 (12:33 -0600)]
Calculate the compensation grid over +X and +Y only (lower-left 0,0), instead of centered 0,0.
Jim Morris [Fri, 10 Feb 2017 07:40:37 +0000 (23:40 -0800)]
Merge pull request #1118 from wolfmanjm/upstreamedge
remove is_square from delta grid, but return a deprecated error inste…
Jim Morris [Fri, 10 Feb 2017 07:38:41 +0000 (23:38 -0800)]
remove is_square from delta grid, but return a deprecated error instead for now
Jim Morris [Fri, 10 Feb 2017 07:15:51 +0000 (23:15 -0800)]
Merge pull request #1117 from Smoothieware/cart-grid
rectangular z grid probe
Jim Morris [Fri, 10 Feb 2017 07:11:02 +0000 (23:11 -0800)]
change width length to x_size, y_size
Jim Morris [Fri, 10 Feb 2017 07:05:41 +0000 (23:05 -0800)]
fix some stuff modify other stuff
Jim Morris [Fri, 10 Feb 2017 06:48:36 +0000 (22:48 -0800)]
Merge branch 'cart-grid' of git://github.com/lordofhyphens/Smoothieware into cart-grid
Joseph Lenox [Fri, 10 Feb 2017 06:27:25 +0000 (00:27 -0600)]
Fixed descriptive text.
Joseph Lenox [Fri, 10 Feb 2017 05:06:55 +0000 (23:06 -0600)]
Initial commit for cart-grid, or cartesian-grid.
Assumes that 0,0 is in the corner.
Jim Morris [Wed, 8 Feb 2017 22:06:15 +0000 (14:06 -0800)]
Merge pull request #1114 from wolfmanjm/upstreamedge
fix switch momentary/toggle config setting
Jim Morris [Wed, 8 Feb 2017 22:04:32 +0000 (14:04 -0800)]
fix switch momentary/toggle config setting
Jim Morris [Wed, 8 Feb 2017 06:14:34 +0000 (22:14 -0800)]
update firmware.bin
Jim Morris [Wed, 8 Feb 2017 05:54:24 +0000 (21:54 -0800)]
Merge remote-tracking branch 'upstream/edge' into stepticker/use-64bit-fixed-point
Jim Morris [Wed, 8 Feb 2017 05:49:17 +0000 (21:49 -0800)]
Merge pull request #1111 from wolfmanjm/upstreamedge
fix config entries for delta grid
Jim Morris [Wed, 8 Feb 2017 05:48:29 +0000 (21:48 -0800)]
fix config entries for delta grid
Jim Morris [Wed, 8 Feb 2017 05:40:49 +0000 (21:40 -0800)]
Merge pull request #1110 from wolfmanjm/upstreamedge
fix zprobe to detect if config of LS failed.
Jim Morris [Wed, 8 Feb 2017 05:39:25 +0000 (21:39 -0800)]
fix zprobe to deteect of config of LS failed.
Jim Morris [Wed, 8 Feb 2017 04:38:12 +0000 (20:38 -0800)]
use 64 bit fixed point for stepticker
Jim Morris [Wed, 8 Feb 2017 04:15:27 +0000 (20:15 -0800)]
Merge pull request #1109 from wolfmanjm/upstreamedge
when is_square is set return error if dimensions changed between conf…
Jim Morris [Wed, 8 Feb 2017 04:14:12 +0000 (20:14 -0800)]
when is_square is set return error if dimensions changed between config and saved grid
Jim Morris [Wed, 8 Feb 2017 03:16:57 +0000 (19:16 -0800)]
Merge pull request #1108 from wolfmanjm/upstreamedge
Clean up is_square config handling for delta grid
Jim Morris [Wed, 8 Feb 2017 03:14:49 +0000 (19:14 -0800)]
Clean up is_square config handling for delta grid
max_x and max_y MUST be defined now when is_square is set
Jim Morris [Wed, 8 Feb 2017 02:23:11 +0000 (18:23 -0800)]
Merge pull request #1107 from lordofhyphens/fix-delta-radius
Set delta_grid when using is_square to be the half diagonal of square
Joseph Lenox [Wed, 8 Feb 2017 02:10:54 +0000 (20:10 -0600)]
Redefine delta_grid when using is_square to be the half diagonal of the square defined by the larger of x_max or y_max.
Jim Morris [Tue, 24 Jan 2017 05:27:32 +0000 (21:27 -0800)]
Merge pull request #1100 from wolfmanjm/upstreamedge
fix typo
Jim Morris [Tue, 24 Jan 2017 05:26:45 +0000 (21:26 -0800)]
fix type
Jim Morris [Tue, 24 Jan 2017 04:37:33 +0000 (20:37 -0800)]
Merge pull request #1099 from wolfmanjm/upstreamedge
fast-stream.py handle target being in halt state
Jim Morris [Tue, 24 Jan 2017 04:35:34 +0000 (20:35 -0800)]
handle target being in halt state
Jim Morris [Tue, 24 Jan 2017 04:29:58 +0000 (20:29 -0800)]
check for halt condition
Jim Morris [Sun, 22 Jan 2017 05:35:23 +0000 (21:35 -0800)]
Merge remote-tracking branch 'upstream/edge' into upstreamedge
Conflicts:
fast-stream.py
Jim Morris [Sun, 22 Jan 2017 05:31:29 +0000 (21:31 -0800)]
Create fast-stream.py
example of how to fast stream over USB serial to smoothie
Jim Morris [Sun, 22 Jan 2017 05:28:58 +0000 (21:28 -0800)]
added example script of fast stream over USB
Arthur Wolf [Thu, 19 Jan 2017 15:14:26 +0000 (16:14 +0100)]
Updating laser config to the latest format in delta config
Arthur Wolf [Thu, 19 Jan 2017 15:13:38 +0000 (16:13 +0100)]
Updating laser config to the latest format
Arthur Wolf [Thu, 19 Jan 2017 15:08:09 +0000 (16:08 +0100)]
Adapting config changes from cartesian to delta
Changes ( cosmetic ones ) were made to the cartesian config, I am porting them to the delta file. This was done using diff software, and does not change the content of the file just it's appearance.
I also added a delta grid configuration example.
Jim Morris [Thu, 19 Jan 2017 04:25:10 +0000 (20:25 -0800)]
update firmware.bin
Jim Morris [Thu, 19 Jan 2017 04:23:08 +0000 (20:23 -0800)]
Merge pull request #1095 from wolfmanjm/upstreamedge
Fix bug that did not allow the enable pin for a motor to be set to nc…
Jim Morris [Thu, 19 Jan 2017 04:21:39 +0000 (20:21 -0800)]
Merge remote-tracking branch 'upstream/edge' into upstreamedge
Jim Morris [Thu, 19 Jan 2017 04:19:53 +0000 (20:19 -0800)]
Fix bug that did not allow the enable pin for a motor to be set to nc (as needed with SPI drivers)
Fix error messages in SPI drivers module
Fix HALT setting enable in SPI drivers in on_idle so it does not crash
Arthur Wolf [Tue, 17 Jan 2017 12:51:34 +0000 (13:51 +0100)]
Merge pull request #1093 from Smoothieware/feature/config-minor-rework
Minor cosmetic config changes
Jim Morris [Mon, 16 Jan 2017 21:22:43 +0000 (13:22 -0800)]
Merge pull request #1094 from FluffyKaon/edge
Fix the z-probe delta grid code for cartesian printers.
laetitia [Mon, 16 Jan 2017 20:48:38 +0000 (13:48 -0700)]
Fix the z-probe delta grid code for cartesian printers.
Arthur Wolf [Sun, 15 Jan 2017 12:33:53 +0000 (13:33 +0100)]
Minor cosmetic config changes
Added some config option informations, made a few minor cosmetic changes, added some links, removed a few options users shouldn't mess with anyway
Jim Morris [Wed, 11 Jan 2017 05:11:57 +0000 (21:11 -0800)]
Merge pull request #1091 from wolfmanjm/upstreamedge
fix make clean for windows
Jim Morris [Wed, 11 Jan 2017 04:36:34 +0000 (20:36 -0800)]
fix make clean for windows
Jim Morris [Mon, 9 Jan 2017 03:29:19 +0000 (19:29 -0800)]
Merge pull request #1088 from wolfmanjm/upstreamedge
Fix max actuator speed checking in robot to exclude extruders
Jim Morris [Mon, 9 Jan 2017 03:26:41 +0000 (19:26 -0800)]
FIx max actuator speed checking in robot to exclude extruders
Jim Morris [Mon, 9 Jan 2017 03:12:35 +0000 (19:12 -0800)]
update firmware.bin
Jim Morris [Mon, 9 Jan 2017 03:09:39 +0000 (19:09 -0800)]
Merge pull request #1087 from wolfmanjm/upstreamedge
Fix M92, M203, M204 for extruders in a n-axis world
Jim Morris [Mon, 9 Jan 2017 03:07:17 +0000 (19:07 -0800)]
Fix M92, M203, M204 for extruders in a n-axis world
Jim Morris [Sun, 8 Jan 2017 22:19:55 +0000 (14:19 -0800)]
update firmware.bin
Jim Morris [Sun, 8 Jan 2017 22:13:13 +0000 (14:13 -0800)]
fix typo
Jim Morris [Tue, 3 Jan 2017 07:51:18 +0000 (23:51 -0800)]
update firmware.bin
Jim Morris [Tue, 3 Jan 2017 04:28:19 +0000 (20:28 -0800)]
Merge pull request #1085 from wolfmanjm/upstreamedge
Modify axis designator for the advanced motordriver controlller
Jim Morris [Tue, 3 Jan 2017 04:24:55 +0000 (20:24 -0800)]
issue Error: for message on alarm
Jim Morris [Tue, 3 Jan 2017 04:20:55 +0000 (20:20 -0800)]
Change the advanced motor config setting from designator to axis
Jim Morris [Mon, 2 Jan 2017 21:56:52 +0000 (13:56 -0800)]
update firmware.bin
Jim Morris [Mon, 2 Jan 2017 21:53:11 +0000 (13:53 -0800)]
Merge pull request #1083 from wolfmanjm/upstreamedge
Fix very old bug in Panel menu