Jim Morris [Thu, 20 Oct 2016 21:33:57 +0000 (14:33 -0700)]
Increase timeout max to 2040 secs or 34 minutes
Jim Morris [Thu, 20 Oct 2016 06:23:21 +0000 (23:23 -0700)]
add extra cooling down timeout for runaway
Pack more stuff in header so we do not have any net gain in memory usage (the 16 bits would have been padded to 32 before).
Add Cooling DOWN state so if temp is set lower it has a cooling down timeout (defaulkt is the same as heating up)
Jim Morris [Tue, 18 Oct 2016 06:56:47 +0000 (23:56 -0700)]
increase runaway_heating_timeout to a max of 511 seconds
decrease runaway_range to a max of 63 degrees
Jim Morris [Tue, 18 Oct 2016 04:42:50 +0000 (21:42 -0700)]
First pass at a simple fix for the runaway issue where changing the temp causes ON_HALT
Jim Morris [Tue, 18 Oct 2016 04:40:49 +0000 (21:40 -0700)]
some comments
Jim Morris [Mon, 17 Oct 2016 20:24:33 +0000 (13:24 -0700)]
add comments
Jim Morris [Mon, 17 Oct 2016 20:08:16 +0000 (13:08 -0700)]
fix extruder actuator setting when reseting axis
Jim Morris [Mon, 17 Oct 2016 19:42:02 +0000 (12:42 -0700)]
Fix typos in for loop
Jim Morris [Sun, 16 Oct 2016 22:05:05 +0000 (15:05 -0700)]
setting for an actuator to be an extruder
check the actuator is an extruder before applying or using e_scale()
Jim Morris [Sun, 16 Oct 2016 10:50:04 +0000 (03:50 -0700)]
Reset ABC and/or E axis correctly in reset_position_from_current_actuator_position()
in G92 En handle e scale properly if n != 0
Jim Morris [Sun, 16 Oct 2016 10:11:45 +0000 (03:11 -0700)]
Merge remote-tracking branch 'upstream/edge' into feature/e-endstop
Jim Morris [Sun, 16 Oct 2016 10:09:57 +0000 (03:09 -0700)]
Merge pull request #1043 from wolfmanjm/feature/Allow-relative-G10-L2
Allow relative mode to affect G10 L2
Jim Morris [Sun, 16 Oct 2016 10:07:26 +0000 (03:07 -0700)]
Allow relative mode to affect G10 L2
Jim Morris [Sun, 16 Oct 2016 05:27:09 +0000 (22:27 -0700)]
Merge remote-tracking branch 'upstream/edge' into feature/e-endstop
Jim Morris [Sun, 16 Oct 2016 05:23:03 +0000 (22:23 -0700)]
Merge pull request #1042 from wolfmanjm/feature/M18-allow-axis-parameter
Feature/m18 allow axis parameter
Jim Morris [Sun, 16 Oct 2016 05:18:36 +0000 (22:18 -0700)]
Add motor_id to stepper motors so they know what axis they are
Change MotorDriver Control so that the designator is actually the axis it is attached to.
Jim Morris [Sun, 16 Oct 2016 04:11:21 +0000 (21:11 -0700)]
Allow M18 E0 to act on currently selected extruder
Jim Morris [Sun, 16 Oct 2016 04:05:22 +0000 (21:05 -0700)]
Allow M18 to turn off selected motors
Jim Morris [Sun, 16 Oct 2016 03:25:36 +0000 (20:25 -0700)]
Merge remote-tracking branch 'upstream/edge' into upstreamedge
Jim Morris [Sat, 15 Oct 2016 04:51:11 +0000 (21:51 -0700)]
comment out max endstops if not used
Jim Morris [Sat, 15 Oct 2016 04:49:01 +0000 (21:49 -0700)]
add Snippet config for enabllin ABC axis. Old syntax left in Config Sample
Jim Morris [Fri, 14 Oct 2016 07:41:33 +0000 (00:41 -0700)]
update firmware.bin
Jim Morris [Fri, 14 Oct 2016 07:39:43 +0000 (00:39 -0700)]
Merge remote-tracking branch 'upstream/edge' into feature/e-endstop
Jim Morris [Fri, 14 Oct 2016 07:38:54 +0000 (00:38 -0700)]
Merge pull request #1041 from wolfmanjm/upstreamedge
Better and correct fix for Kill hanging on E moving
Jim Morris [Fri, 14 Oct 2016 07:27:48 +0000 (00:27 -0700)]
Merge remote-tracking branch 'upstream/edge' into feature/e-endstop
Jim Morris [Fri, 14 Oct 2016 07:25:59 +0000 (00:25 -0700)]
Merge remote-tracking branch 'upstream/edge' into upstreamedge
Jim Morris [Fri, 14 Oct 2016 07:21:36 +0000 (00:21 -0700)]
update firmware.bin
Jim Morris [Fri, 14 Oct 2016 07:15:28 +0000 (00:15 -0700)]
Better and correct fix for Kill hanging on E moving
Jim Morris [Thu, 13 Oct 2016 22:56:15 +0000 (15:56 -0700)]
update firmware.bin
Jim Morris [Thu, 13 Oct 2016 22:53:12 +0000 (15:53 -0700)]
Merge pull request #1040 from wolfmanjm/upstreamedge
workaround to handle kill and not wait for motors to stop
Jim Morris [Thu, 13 Oct 2016 22:52:15 +0000 (15:52 -0700)]
change ERROR : to ERROR: for out of band temp errors
Jim Morris [Thu, 13 Oct 2016 09:00:52 +0000 (02:00 -0700)]
workaround to handle kill and not wait for motors to stop as that seems to hang
Jim Morris [Thu, 13 Oct 2016 06:20:39 +0000 (23:20 -0700)]
Merge remote-tracking branch 'upstream/edge' into feature/e-endstop
Jim Morris [Wed, 12 Oct 2016 21:13:39 +0000 (14:13 -0700)]
Merge pull request #1038 from michael-moore0/feature/time-format
modified timestamp format to HH:MM:SS.
Jim Morris [Wed, 12 Oct 2016 21:12:26 +0000 (14:12 -0700)]
Merge pull request #1039 from michael-moore0/feature/implement-mkdir
implemented the 'mkdir' command on the shell.
Michael Moore [Wed, 12 Oct 2016 20:46:59 +0000 (16:46 -0400)]
implemented the 'mkdir' command on the shell.
Michael Moore [Wed, 12 Oct 2016 13:35:13 +0000 (09:35 -0400)]
fixed whitespace issue and removed 'sd' to correct spacing.
Michael Moore [Wed, 12 Oct 2016 02:05:56 +0000 (22:05 -0400)]
modified timestamp format to HH:MM:SS.
- modified watch screen time format.
- modified 'progress' command time format.
Jim Morris [Sun, 9 Oct 2016 05:19:51 +0000 (22:19 -0700)]
Merge remote-tracking branch 'upstream/edge' into feature/e-endstop
Jim Morris [Sun, 9 Oct 2016 05:18:35 +0000 (22:18 -0700)]
Merge pull request #1036 from wolfmanjm/upstreamedge
Add fix to not recursively call refresh in ON_IDLE
Jim Morris [Sun, 9 Oct 2016 05:16:54 +0000 (22:16 -0700)]
Add fix to not recursively call refresh in ON_IDLE
Jim Morris [Sun, 9 Oct 2016 03:27:31 +0000 (20:27 -0700)]
check probe status before starting probe.
Jim Morris [Fri, 7 Oct 2016 22:09:15 +0000 (15:09 -0700)]
Merge remote-tracking branch 'upstream/edge' into feature/e-endstop
Jim Morris [Fri, 7 Oct 2016 19:32:27 +0000 (12:32 -0700)]
clean up M119 and limit switch hit messages
Jim Morris [Fri, 7 Oct 2016 19:13:28 +0000 (12:13 -0700)]
move where compensation transform is disabled so axis reset gets it right and Z does not move during home
Jim Morris [Thu, 6 Oct 2016 05:36:42 +0000 (22:36 -0700)]
Fix detection of endstops when it is a corexy and X or Y are moving.
Jim Morris [Thu, 6 Oct 2016 04:55:12 +0000 (21:55 -0700)]
update comments
Jim Morris [Wed, 5 Oct 2016 04:37:42 +0000 (21:37 -0700)]
Delete ZprobeGrid.config
Jim Morris [Wed, 5 Oct 2016 00:18:01 +0000 (17:18 -0700)]
Add more info to M119 to show pins as well as homing endstops
implement the manual homing for axis ABC
fix the reset axis for axis ABC
Jim Morris [Tue, 4 Oct 2016 20:20:26 +0000 (13:20 -0700)]
allow homing of A B and C individually
Jim Morris [Tue, 4 Oct 2016 19:59:24 +0000 (12:59 -0700)]
completed refactor
added new config for ABC endstops
changed the public access for homing_offset
Jim Morris [Tue, 4 Oct 2016 00:48:28 +0000 (17:48 -0700)]
refactor again to split pin info of endstops from homing axis info
Jim Morris [Mon, 3 Oct 2016 22:06:16 +0000 (15:06 -0700)]
major refactor of endstop definitions and storage
introdue new syntax for endstops config requied for using ABC endstops
Jim Morris [Mon, 3 Oct 2016 18:03:31 +0000 (11:03 -0700)]
Merge branch 'fix/inverse-transform' into feature/e-endstop
Jim Morris [Mon, 3 Oct 2016 18:03:13 +0000 (11:03 -0700)]
comment
Jim Morris [Mon, 3 Oct 2016 04:39:30 +0000 (21:39 -0700)]
Merge branch 'fix/inverse-transform' into feature/e-endstop
Jim Morris [Mon, 3 Oct 2016 04:37:05 +0000 (21:37 -0700)]
refactor to rename last_milestone to machine_position, and last_machne_position to compensated_machine_position
Thi smore accurately refelcts what is going on and will hopefully reduce confusion
Jim Morris [Mon, 3 Oct 2016 00:55:23 +0000 (17:55 -0700)]
refactor endstops pins to handle three extra axis
initial handling of A axis homing
Jim Morris [Sun, 2 Oct 2016 20:23:48 +0000 (13:23 -0700)]
change M306 again to use MCS position not actuator position
Jim Morris [Sun, 2 Oct 2016 06:02:23 +0000 (23:02 -0700)]
set homed for all axis if a delta
Jim Morris [Sun, 2 Oct 2016 05:55:28 +0000 (22:55 -0700)]
Introduce concept of homed or not
add G28.6 to display homed status
add G28.5 to clear homed status (set unhomed ala linuxcnc)
M306 now requires axis be homed or returns error, and forces axis to be homed before setting it again
Note M306 may still be buggy if compenstaion transform is on
Jim Morris [Sat, 1 Oct 2016 07:09:03 +0000 (00:09 -0700)]
Fix reset_axis_position for homing.
we are given the post compensation position sdo use inverse transform to get last milestone
Change the way G30 Zxxx works.
so it actually just does a G92 Zxxx after the probe
Jim Morris [Wed, 28 Sep 2016 05:49:24 +0000 (22:49 -0700)]
Fix homing comamnds if in grbl mode
Jim Morris [Wed, 28 Sep 2016 05:40:30 +0000 (22:40 -0700)]
more zprobe refactor, remove probeDistance()
Jim Morris [Wed, 28 Sep 2016 05:30:43 +0000 (22:30 -0700)]
refactor zprobe probe return to be a method and returns to saved last_milestone so compensation will be taken into account
Jim Morris [Sat, 24 Sep 2016 22:43:56 +0000 (15:43 -0700)]
Merge remote-tracking branch 'upstream/edge' into fix/inverse-transform
Jim Morris [Sat, 24 Sep 2016 22:33:37 +0000 (15:33 -0700)]
Merge pull request #1033 from wolfmanjm/upstreamedge
add BS and DEL to the USB serial to delete last character entered
Jim Morris [Sat, 24 Sep 2016 22:31:53 +0000 (15:31 -0700)]
add BS and DEL to the USB serial to delete last chanracter entered, gives simple line editing to commands
Jim Morris [Sat, 24 Sep 2016 20:38:15 +0000 (13:38 -0700)]
Merge pull request #1031 from nallar/patch-1
Fix broken link in README (HowToFileIssues.md)
Arthur Wolf [Sat, 24 Sep 2016 18:22:31 +0000 (20:22 +0200)]
Making it clear issues are for issue ( Duh. )
Ross Allan [Sat, 24 Sep 2016 13:11:23 +0000 (14:11 +0100)]
Fix broken link in README (HowToFileIssues.md)
Was linking to HowToFileIssues.md which was renamed in these commits
7bb7936875 3fd39027e to ISSUE_TEMPLATE.md
Jim Morris [Fri, 23 Sep 2016 20:24:36 +0000 (13:24 -0700)]
Merge branch 'upstreamedge' into fix/inverse-transform
Jim Morris [Fri, 23 Sep 2016 20:24:00 +0000 (13:24 -0700)]
Merge pull request #1030 from wolfmanjm/upstreamedge
add a set_g92 x,y,z to config
Jim Morris [Fri, 23 Sep 2016 20:22:11 +0000 (13:22 -0700)]
add a set_g92 x,y,z to config
Jim Morris [Thu, 22 Sep 2016 05:48:18 +0000 (22:48 -0700)]
Merge pull request #1029 from wolfmanjm/upstreamedge
fix modifyvalue screen, update laser screen
Jim Morris [Thu, 22 Sep 2016 05:42:00 +0000 (22:42 -0700)]
Merge branch 'upstreamedge' into fix/inverse-transform
Jim Morris [Thu, 22 Sep 2016 05:41:07 +0000 (22:41 -0700)]
fix single entry ModifyValuesScreen when not immediate set
Jim Morris [Wed, 21 Sep 2016 07:59:09 +0000 (00:59 -0700)]
Merge branch 'upstreamedge' into fix/inverse-transform
Jim Morris [Wed, 21 Sep 2016 07:54:59 +0000 (00:54 -0700)]
add set S value menu item to laser screen
Jim Morris [Wed, 21 Sep 2016 06:39:58 +0000 (23:39 -0700)]
update firmware.bin
Jim Morris [Wed, 21 Sep 2016 06:37:45 +0000 (23:37 -0700)]
Merge pull request #1028 from wolfmanjm/upstreamedge
fix watchscree
Jim Morris [Wed, 21 Sep 2016 06:36:09 +0000 (23:36 -0700)]
fix watchscree
Jim Morris [Sat, 17 Sep 2016 20:39:05 +0000 (13:39 -0700)]
fix M306 again
Jim Morris [Sat, 17 Sep 2016 20:11:37 +0000 (13:11 -0700)]
change the way M306 sets home offset
Jim Morris [Sat, 17 Sep 2016 20:05:51 +0000 (13:05 -0700)]
remove zgrid strategy form build, as it has been replaced by delta grid which also handles square beds now.
Jim Morris [Thu, 15 Sep 2016 20:31:47 +0000 (13:31 -0700)]
Merge remote-tracking branch 'upstream/edge' into fix/inverse-transform
Jim Morris [Thu, 15 Sep 2016 20:31:11 +0000 (13:31 -0700)]
Merge pull request #1025 from wolfmanjm/upstreamedge
Single entry ModifyValue menus go straight into value update mode and…
Jim Morris [Thu, 15 Sep 2016 20:27:52 +0000 (13:27 -0700)]
Single entry ModifyValue menus go straight into value update mode and exit direct to parent
No need to disolay a selection menu when only one entry.
Update laser power setting to use the above
Jim Morris [Wed, 14 Sep 2016 23:15:58 +0000 (16:15 -0700)]
fix ? to use inverse transform
Jim Morris [Wed, 14 Sep 2016 20:19:00 +0000 (13:19 -0700)]
add inverse compensation transform
use inverse transform for reseting axis from actuator position
All probes leave compensation transform on now
homing will use compensation transform to get actual position at the given position
? and M114.1 and M114.2 will return corrected position based on compensation transform
Jim Morris [Wed, 14 Sep 2016 17:31:41 +0000 (10:31 -0700)]
Merge pull request #1023 from docdawning/patch-1
Update Readme.md
James [Wed, 14 Sep 2016 15:29:56 +0000 (09:29 -0600)]
Update Readme.md
s/alos/also
Jim Morris [Tue, 13 Sep 2016 20:49:28 +0000 (13:49 -0700)]
Merge pull request #1022 from wolfmanjm/features/laser-panel
Features/laser panel
Jim Morris [Tue, 13 Sep 2016 20:48:36 +0000 (13:48 -0700)]
add comments
Jim Morris [Tue, 13 Sep 2016 20:05:34 +0000 (13:05 -0700)]
add option to test fire menu to leave laser on when it exits, and disable the timeout
Jim Morris [Tue, 13 Sep 2016 07:28:23 +0000 (00:28 -0700)]
update control screen for both 3dprinter and cnc uses same file, fixes jogging in absolute mode for 3dprinter
added actual current laser power to watch screen
Jim Morris [Tue, 13 Sep 2016 06:20:20 +0000 (23:20 -0700)]
Add laser menu
sets power scaler
does test fire
Add Dynamic Menu class
Add Goto park position and set park position for CNC mode
Add current laser power value (S value) to watch screen
Jim Morris [Sat, 10 Sep 2016 19:07:17 +0000 (12:07 -0700)]
Update Readme.md
Jim Morris [Fri, 9 Sep 2016 05:15:21 +0000 (22:15 -0700)]
Merge remote-tracking branch 'upstream/edge' into features/laser-panel
Jim Morris [Thu, 8 Sep 2016 05:56:23 +0000 (22:56 -0700)]
Create PULL_REQUEST_TEMPLATE.md