X-Git-Url: https://git.hcoop.net/clinton/Smoothieware.git/blobdiff_plain/e4bae6f662de69645bfbb9a57b723d619902df3c..f95320b7155f6fe614f7579727b840ffb01248e6:/src/modules/tools/zprobe/ZProbe.cpp

diff --git a/src/modules/tools/zprobe/ZProbe.cpp b/src/modules/tools/zprobe/ZProbe.cpp
index 961e68fe..98240b89 100644
--- a/src/modules/tools/zprobe/ZProbe.cpp
+++ b/src/modules/tools/zprobe/ZProbe.cpp
@@ -31,6 +31,7 @@
 #include "DeltaCalibrationStrategy.h"
 #include "ThreePointStrategy.h"
 #include "DeltaGridStrategy.h"
+#include "CartGridStrategy.h"
 
 #define enable_checksum          CHECKSUM("enable")
 #define probe_pin_checksum       CHECKSUM("probe_pin")
@@ -40,7 +41,9 @@
 #define return_feedrate_checksum CHECKSUM("return_feedrate")
 #define probe_height_checksum    CHECKSUM("probe_height")
 #define gamma_max_checksum       CHECKSUM("gamma_max")
+#define max_z_checksum           CHECKSUM("max_z")
 #define reverse_z_direction_checksum CHECKSUM("reverse_z")
+#define dwell_before_probing_checksum CHECKSUM("dwell_before_probing")
 
 // from endstop section
 #define delta_homing_checksum    CHECKSUM("delta_homing")
@@ -54,8 +57,6 @@
 #define STEPS_PER_MM(a) (STEPPER[a]->get_steps_per_mm())
 #define Z_STEPS_PER_MM STEPS_PER_MM(Z_AXIS)
 
-#define abs(a) ((a<0) ? -a : a)
-
 void ZProbe::on_module_loaded()
 {
     // if the module is disabled -> do nothing
@@ -70,7 +71,7 @@ void ZProbe::on_module_loaded()
     // register event-handlers
     register_for_event(ON_GCODE_RECEIVED);
 
-    // we read the probe in this timer, currently only for G38 probes.
+    // we read the probe in this timer
     probing= false;
     THEKERNEL->slow_ticker->attach(1000, this, &ZProbe::read_probe);
 }
@@ -86,25 +87,38 @@ void ZProbe::config_load()
     for( auto cs : modules ){
         if( THEKERNEL->config->value(leveling_strategy_checksum, cs, enable_checksum )->as_bool() ){
             bool found= false;
+            LevelingStrategy *ls= nullptr;
+
             // check with each known strategy and load it if it matches
             switch(cs) {
                 case delta_calibration_strategy_checksum:
-                    this->strategies.push_back(new DeltaCalibrationStrategy(this));
+                    ls= new DeltaCalibrationStrategy(this);
                     found= true;
                     break;
 
                 case three_point_leveling_strategy_checksum:
                     // NOTE this strategy is mutually exclusive with the delta calibration strategy
-                    this->strategies.push_back(new ThreePointStrategy(this));
+                    ls= new ThreePointStrategy(this);
                     found= true;
                     break;
 
                 case delta_grid_leveling_strategy_checksum:
-                    this->strategies.push_back(new DeltaGridStrategy(this));
+                    ls= new DeltaGridStrategy(this);
+                    found= true;
+                    break;
+
+                case cart_grid_leveling_strategy_checksum:
+                    ls= new CartGridStrategy(this);
                     found= true;
                     break;
             }
-            if(found) this->strategies.back()->handleConfig();
+            if(found) {
+                if(ls->handleConfig()) {
+                    this->strategies.push_back(ls);
+                }else{
+                    delete ls;
+                }
+            }
         }
     }
 
@@ -126,7 +140,12 @@ void ZProbe::config_load()
     this->fast_feedrate = THEKERNEL->config->value(zprobe_checksum, fast_feedrate_checksum)->by_default(100)->as_number(); // feedrate in mm/sec
     this->return_feedrate = THEKERNEL->config->value(zprobe_checksum, return_feedrate_checksum)->by_default(0)->as_number(); // feedrate in mm/sec
     this->reverse_z     = THEKERNEL->config->value(zprobe_checksum, reverse_z_direction_checksum)->by_default(false)->as_bool(); // Z probe moves in reverse direction
-    this->max_z         = THEKERNEL->config->value(gamma_max_checksum)->by_default(500)->as_number(); // maximum zprobe distance
+    this->max_z         = THEKERNEL->config->value(zprobe_checksum, max_z_checksum)->by_default(NAN)->as_number(); // maximum zprobe distance
+    if(isnan(this->max_z)){
+        this->max_z = THEKERNEL->config->value(gamma_max_checksum)->by_default(200)->as_number(); // maximum zprobe distance
+    }
+    this->dwell_before_probing = THEKERNEL->config->value(zprobe_checksum, dwell_before_probing_checksum)->by_default(0)->as_number(); // dwell time in seconds before probing
+
 }
 
 uint32_t ZProbe::read_probe(uint32_t dummy)
@@ -160,6 +179,13 @@ uint32_t ZProbe::read_probe(uint32_t dummy)
 // returns boolean value indicating if probe was triggered
 bool ZProbe::run_probe(float& mm, float feedrate, float max_dist, bool reverse)
 {
+    if(dwell_before_probing > .0001F) safe_delay_ms(dwell_before_probing*1000);
+
+    if(this->pin.get()) {
+        // probe already triggered so abort
+        return false;
+    }
+
     float maxz= max_dist < 0 ? this->max_z*2 : max_dist;
 
     probing= true;
@@ -167,14 +193,9 @@ bool ZProbe::run_probe(float& mm, float feedrate, float max_dist, bool reverse)
     debounce= 0;
 
     // save current actuator position so we can report how far we moved
-    ActuatorCoordinates start_pos{
-        THEROBOT->actuators[X_AXIS]->get_current_position(),
-        THEROBOT->actuators[Y_AXIS]->get_current_position(),
-        THEROBOT->actuators[Z_AXIS]->get_current_position()
-    };
+    float z_start_pos= THEROBOT->actuators[Z_AXIS]->get_current_position();
 
     // move Z down
-    THEROBOT->disable_segmentation= true; // we must disable segmentation as this won't work with it enabled
     bool dir= (!reverse_z != reverse); // xor
     float delta[3]= {0,0,0};
     delta[Z_AXIS]= dir ? -maxz : maxz;
@@ -182,19 +203,13 @@ bool ZProbe::run_probe(float& mm, float feedrate, float max_dist, bool reverse)
 
     // wait until finished
     THECONVEYOR->wait_for_idle();
-    THEROBOT->disable_segmentation= false;
 
     // now see how far we moved, get delta in z we moved
     // NOTE this works for deltas as well as all three actuators move the same amount in Z
-    mm= start_pos[2] - THEROBOT->actuators[2]->get_current_position();
+    mm= z_start_pos - THEROBOT->actuators[2]->get_current_position();
 
     // set the last probe position to the actuator units moved during this home
-    THEROBOT->set_last_probe_position(
-        std::make_tuple(
-            start_pos[0] - THEROBOT->actuators[0]->get_current_position(),
-            start_pos[1] - THEROBOT->actuators[1]->get_current_position(),
-            mm,
-            probe_detected?1:0));
+    THEROBOT->set_last_probe_position(std::make_tuple(0, 0, mm, probe_detected?1:0));
 
     probing= false;
 
@@ -206,8 +221,13 @@ bool ZProbe::run_probe(float& mm, float feedrate, float max_dist, bool reverse)
     return probe_detected;
 }
 
-bool ZProbe::return_probe(float mm, bool reverse)
+// do probe then return to start position
+bool ZProbe::run_probe_return(float& mm, float feedrate, float max_dist, bool reverse)
 {
+    float save_z_pos= THEROBOT->get_axis_position(Z_AXIS);
+
+    bool ok= run_probe(mm, feedrate, max_dist, reverse);
+
     // move probe back to where it was
     float fr;
     if(this->return_feedrate != 0) { // use return_feedrate if set
@@ -217,38 +237,17 @@ bool ZProbe::return_probe(float mm, bool reverse)
         if(fr > this->fast_feedrate) fr = this->fast_feedrate; // unless that is greater than fast feedrate
     }
 
-    bool dir= ((mm < 0) != reverse_z); // xor
-    if(reverse) dir= !dir;
-
-    float delta[3]= {0,0,0};
-    delta[Z_AXIS]= dir ? -mm : mm;
-    THEROBOT->delta_move(delta, fr, 3);
-
-    // wait until finished
-    THECONVEYOR->wait_for_idle();
+    // absolute move back to saved starting position
+    coordinated_move(NAN, NAN, save_z_pos, fr, false);
 
-    return true;
+    return ok;
 }
 
 bool ZProbe::doProbeAt(float &mm, float x, float y)
 {
-    float s;
     // move to xy
     coordinated_move(x, y, NAN, getFastFeedrate());
-    if(!run_probe(s)) return false;
-
-    // return to original Z
-    return_probe(s);
-    mm = s;
-
-    return true;
-}
-
-float ZProbe::probeDistance(float x, float y)
-{
-    float s;
-    if(!doProbeAt(s, x, y)) return NAN;
-    return s;
+    return run_probe_return(mm, slow_feedrate);
 }
 
 void ZProbe::on_gcode_received(void *argument)
@@ -259,9 +258,10 @@ void ZProbe::on_gcode_received(void *argument)
 
         // make sure the probe is defined and not already triggered before moving motors
         if(!this->pin.connected()) {
-            gcode->stream->printf("ZProbe not connected.\n");
+            gcode->stream->printf("ZProbe pin not configured.\n");
             return;
         }
+
         if(this->pin.get()) {
             gcode->stream->printf("ZProbe triggered before move, aborting command.\n");
             return;
@@ -271,40 +271,30 @@ void ZProbe::on_gcode_received(void *argument)
             // first wait for all moves to finish
             THEKERNEL->conveyor->wait_for_idle();
 
+            bool set_z= (gcode->has_letter('Z') && !is_rdelta);
             bool probe_result;
             bool reverse= (gcode->has_letter('R') && gcode->get_value('R') != 0); // specify to probe in reverse direction
             float rate= gcode->has_letter('F') ? gcode->get_value('F') / 60 : this->slow_feedrate;
             float mm;
-            probe_result = run_probe(mm, rate, -1, reverse);
+
+            // if not setting Z then return probe to where it started, otherwise leave it where it is
+            probe_result = (set_z ? run_probe(mm, rate, -1, reverse) : run_probe_return(mm, rate, -1, reverse));
 
             if(probe_result) {
-                // the result is in actuator coordinates and raw steps
-                gcode->stream->printf("Z:%1.4f\n", mm);
-
-                // set the last probe position to the current actuator units
-                THEROBOT->set_last_probe_position(std::make_tuple(
-                    THEROBOT->actuators[X_AXIS]->get_current_position(),
-                    THEROBOT->actuators[Y_AXIS]->get_current_position(),
-                    THEROBOT->actuators[Z_AXIS]->get_current_position(),
-                    1));
-
-                // move back to where it started, unless a Z is specified (and not a rotary delta)
-                if(gcode->has_letter('Z') && !is_rdelta) {
-                    // set Z to the specified value, and leave probe where it is
-                    THEROBOT->reset_axis_position(gcode->get_value('Z'), Z_AXIS);
-
-                } else {
-                    // return to pre probe position
-                    return_probe(mm, reverse);
+                // the result is in actuator coordinates moved
+                gcode->stream->printf("Z:%1.4f\n", THEKERNEL->robot->from_millimeters(mm));
+
+                if(set_z) {
+                    // set current Z to the specified value, shortcut for G92 Znnn
+                    char buf[32];
+                    int n = snprintf(buf, sizeof(buf), "G92 Z%f", gcode->get_value('Z'));
+                    string g(buf, n);
+                    Gcode gc(g, &(StreamOutput::NullStream));
+                    THEKERNEL->call_event(ON_GCODE_RECEIVED, &gc);
                 }
 
             } else {
                 gcode->stream->printf("ZProbe not triggered\n");
-                THEROBOT->set_last_probe_position(std::make_tuple(
-                    THEROBOT->actuators[X_AXIS]->get_current_position(),
-                    THEROBOT->actuators[Y_AXIS]->get_current_position(),
-                    THEROBOT->actuators[Z_AXIS]->get_current_position(),
-                    0));
             }
 
         } else {
@@ -335,8 +325,8 @@ void ZProbe::on_gcode_received(void *argument)
 
     } else if(gcode->has_g && gcode->g == 38 ) { // G38.2 Straight Probe with error, G38.3 straight probe without error
         // linuxcnc/grbl style probe http://www.linuxcnc.org/docs/2.5/html/gcode/gcode.html#sec:G38-probe
-        if(gcode->subcode != 2 && gcode->subcode != 3) {
-            gcode->stream->printf("error:Only G38.2 and G38.3 are supported\n");
+        if(gcode->subcode < 2 || gcode->subcode > 5) {
+            gcode->stream->printf("error:Only G38.2, G38.3, G38.4, and G38.5 are supported\n");
             return;
         }
 
@@ -346,28 +336,47 @@ void ZProbe::on_gcode_received(void *argument)
             return;
         }
 
-        if(this->pin.get()) {
-            gcode->stream->printf("error:ZProbe triggered before move, aborting command.\n");
-            return;
+        if(gcode->subcode == 4 || gcode->subcode == 5) {
+            if(!this->pin.get()) {
+                gcode->stream->printf("error:ZProbe triggered before move, aborting command.\n");
+                return;
+            }
+        } else {
+            if(this->pin.get()) {
+                gcode->stream->printf("error:ZProbe triggered before move, aborting command.\n");
+                return;
+            }
         }
 
         // first wait for all moves to finish
         THEKERNEL->conveyor->wait_for_idle();
 
+        float x= NAN, y=NAN, z=NAN;
         if(gcode->has_letter('X')) {
-            // probe in the X axis
-            probe_XYZ(gcode, X_AXIS);
+            x= gcode->get_value('X');
+        }
 
-        }else if(gcode->has_letter('Y')) {
-            // probe in the Y axis
-            probe_XYZ(gcode, Y_AXIS);
+        if(gcode->has_letter('Y')) {
+            y= gcode->get_value('Y');
+        }
 
-        }else if(gcode->has_letter('Z')) {
-            // probe in the Z axis
-            probe_XYZ(gcode, Z_AXIS);
+        if(gcode->has_letter('Z')) {
+            z= gcode->get_value('Z');
+        }
 
-        }else{
+        if(isnan(x) && isnan(y) && isnan(z)) {
             gcode->stream->printf("error:at least one of X Y or Z must be specified\n");
+            return;
+        }
+
+        if(gcode->subcode == 4 || gcode->subcode == 5) {
+            pin.set_inverting(pin.is_inverting() != 1);
+        }
+
+        probe_XYZ(gcode, x, y, z);
+
+        if(gcode->subcode == 4 || gcode->subcode == 5) {
+            pin.set_inverting(pin.is_inverting() != 1);
         }
 
         return;
@@ -392,12 +401,13 @@ void ZProbe::on_gcode_received(void *argument)
                     invert_override= (gcode->get_value('I') != 0);
                     pin.set_inverting(pin.is_inverting() != invert_override); // XOR so inverted pin is not inverted and vice versa
                 }
+                if (gcode->has_letter('D')) this->dwell_before_probing = gcode->get_value('D');
                 break;
 
             case 500: // save settings
             case 503: // print settings
-                gcode->stream->printf(";Probe feedrates Slow/fast(K)/Return (mm/sec) max_z (mm) height (mm):\nM670 S%1.2f K%1.2f R%1.2f Z%1.2f H%1.2f\n",
-                    this->slow_feedrate, this->fast_feedrate, this->return_feedrate, this->max_z, this->probe_height);
+                gcode->stream->printf(";Probe feedrates Slow/fast(K)/Return (mm/sec) max_z (mm) height (mm) dwell (s):\nM670 S%1.2f K%1.2f R%1.2f Z%1.2f H%1.2f D%1.2f\n",
+                    this->slow_feedrate, this->fast_feedrate, this->return_feedrate, this->max_z, this->probe_height, this->dwell_before_probing);
 
                 // fall through is intended so leveling strategies can handle m-codes too
 
@@ -412,22 +422,18 @@ void ZProbe::on_gcode_received(void *argument)
 }
 
 // special way to probe in the X or Y or Z direction using planned moves, should work with any kinematics
-void ZProbe::probe_XYZ(Gcode *gcode, int axis)
+void ZProbe::probe_XYZ(Gcode *gcode, float x, float y, float z)
 {
     // enable the probe checking in the timer
     probing= true;
     probe_detected= false;
     THEROBOT->disable_segmentation= true; // we must disable segmentation as this won't work with it enabled (beware on deltas probing in X or Y)
 
-    // get probe feedrate if specified
-    float rate = (gcode->has_letter('F')) ? gcode->get_value('F')*60 : this->slow_feedrate;
+    // get probe feedrate in mm/min and convert to mm/sec if specified
+    float rate = (gcode->has_letter('F')) ? gcode->get_value('F')/60 : this->slow_feedrate;
 
     // do a regular move which will stop as soon as the probe is triggered, or the distance is reached
-    switch(axis) {
-        case X_AXIS: coordinated_move(gcode->get_value('X'), 0, 0, rate, true); break;
-        case Y_AXIS: coordinated_move(0, gcode->get_value('Y'), 0, rate, true); break;
-        case Z_AXIS: coordinated_move(0, 0, gcode->get_value('Z'), rate, true); break;
-    }
+    coordinated_move(x, y, z, rate, true);
 
     // coordinated_move returns when the move is finished
 
@@ -444,12 +450,12 @@ void ZProbe::probe_XYZ(Gcode *gcode, int axis)
     uint8_t probeok= this->probe_detected ? 1 : 0;
 
     // print results using the GRBL format
-    gcode->stream->printf("[PRB:%1.3f,%1.3f,%1.3f:%d]\n", pos[X_AXIS], pos[Y_AXIS], pos[Z_AXIS], probeok);
+    gcode->stream->printf("[PRB:%1.3f,%1.3f,%1.3f:%d]\n", THEKERNEL->robot->from_millimeters(pos[X_AXIS]), THEKERNEL->robot->from_millimeters(pos[Y_AXIS]), THEKERNEL->robot->from_millimeters(pos[Z_AXIS]), probeok);
     THEROBOT->set_last_probe_position(std::make_tuple(pos[X_AXIS], pos[Y_AXIS], pos[Z_AXIS], probeok));
 
-    if(probeok == 0 && gcode->subcode == 2) {
-        // issue error if probe was not triggered and subcode == 2
-        gcode->stream->printf("ALARM:Probe fail\n");
+    if(probeok == 0 && (gcode->subcode == 2 || gcode->subcode == 4)) {
+        // issue error if probe was not triggered and subcode is 2 or 4
+        gcode->stream->printf("ALARM: Probe fail\n");
         THEKERNEL->call_event(ON_HALT, nullptr);
     }
 }
@@ -459,43 +465,51 @@ void ZProbe::probe_XYZ(Gcode *gcode, int axis)
 // NOTE must use G53 to force move in machine coordinates and ignore any WCS offsets
 void ZProbe::coordinated_move(float x, float y, float z, float feedrate, bool relative)
 {
-    char buf[32];
-    char cmd[64];
+    #define CMDLEN 128
+    char *cmd= new char[CMDLEN]; // use heap here to reduce stack usage
 
     if(relative) strcpy(cmd, "G91 G0 ");
     else strcpy(cmd, "G53 G0 "); // G53 forces movement in machine coordinate system
 
     if(!isnan(x)) {
-        int n = snprintf(buf, sizeof(buf), " X%1.3f", x);
-        strncat(cmd, buf, n);
+        size_t n= strlen(cmd);
+        snprintf(&cmd[n], CMDLEN-n, " X%1.3f", x);
     }
     if(!isnan(y)) {
-        int n = snprintf(buf, sizeof(buf), " Y%1.3f", y);
-        strncat(cmd, buf, n);
+        size_t n= strlen(cmd);
+        snprintf(&cmd[n], CMDLEN-n, " Y%1.3f", y);
     }
     if(!isnan(z)) {
-        int n = snprintf(buf, sizeof(buf), " Z%1.3f", z);
-        strncat(cmd, buf, n);
+        size_t n= strlen(cmd);
+        snprintf(&cmd[n], CMDLEN-n, " Z%1.3f", z);
+    }
+
+    {
+        size_t n= strlen(cmd);
+        // use specified feedrate (mm/sec)
+        snprintf(&cmd[n], CMDLEN-n, " F%1.1f", feedrate * 60); // feed rate is converted to mm/min
     }
 
-    // use specified feedrate (mm/sec)
-    int n = snprintf(buf, sizeof(buf), " F%1.1f", feedrate * 60); // feed rate is converted to mm/min
-    strncat(cmd, buf, n);
     if(relative) strcat(cmd, " G90");
 
-    //THEKERNEL->streams->printf("DEBUG: move: %s\n", cmd);
+    //THEKERNEL->streams->printf("DEBUG: move: %s: %u\n", cmd, strlen(cmd));
 
     // send as a command line as may have multiple G codes in it
+    THEROBOT->push_state();
     struct SerialMessage message;
     message.message = cmd;
+    delete [] cmd;
+
     message.stream = &(StreamOutput::NullStream);
     THEKERNEL->call_event(ON_CONSOLE_LINE_RECEIVED, &message );
     THEKERNEL->conveyor->wait_for_idle();
+    THEROBOT->pop_state();
+
 }
 
 // issue home command
 void ZProbe::home()
 {
-    Gcode gc("G28", &(StreamOutput::NullStream));
+    Gcode gc(THEKERNEL->is_grbl_mode() ? "G28.2" : "G28", &(StreamOutput::NullStream));
     THEKERNEL->call_event(ON_GCODE_RECEIVED, &gc);
 }