#leveling-strategy.three-point-leveling.probe_offsets 0,0,0 # the probe offsets from nozzle, must be x,y,z, default is no offset# Robot module configurations : general handling of movement G-codes and slicing into moves default_feed_rate 4000 # Default rate ( mm/minute ) for G1/G2/G3 moves default_seek_rate 4000 # Default rate ( mm/minute ) for G0 moves mm_per_arc_segment 0.5 # Arcs are cut into segments ( lines ), this is the length for these segments. Smaller values mean more resolution, higher values mean faster computation mm_per_line_segment 5 # Lines can be cut into segments ( not usefull with cartesian coordinates robots ). # Arm solution configuration : Cartesian robot. Translates mm positions into stepper positions alpha_steps_per_mm 80 # Steps per mm for alpha stepper beta_steps_per_mm 80 # Steps per mm for beta stepper gamma_steps_per_mm 1637.7953 # Steps per mm for gamma stepper # Planner module configuration : Look-ahead and acceleration configuration planner_queue_size 32 # Size of the planning queue, must be a power of 2. 128 seems to be the maximum. acceleration 3000 # Acceleration in mm/second/second. #z_acceleration 500 # Acceleration for Z only moves in mm/s^2, 0 disables it, disabled by default. DO NOT SET ON A DELTA acceleration_ticks_per_second 1000 # Number of times per second the speed is updated junction_deviation 0.05 # Similar to the old "max_jerk", in millimeters, see : https://github.com/grbl/grbl/blob/master/planner.c#L409 # and https://github.com/grbl/grbl/wiki/Configuring-Grbl-v0.8 . Lower values mean being more careful, higher values means being faster and have more jerk # Stepper module configuration microseconds_per_step_pulse 1 # Duration of step pulses to stepper drivers, in microseconds minimum_steps_per_minute 1200 # Never step slower than this base_stepping_frequency 100000 # Base frequency for stepping, higher gives smoother movement # Stepper module pins ( ports, and pin numbers, appending "!" to the number will invert a pin ) alpha_step_pin 2.1 # Pin for alpha stepper step signal alpha_dir_pin 0.11 # Pin for alpha stepper direction alpha_en_pin 0.10 # Pin for alpha enable pin alpha_current 1.0 # X stepper motor current x_axis_max_speed 30000 # mm/min beta_step_pin 2.2 # Pin for beta stepper step signal beta_dir_pin 0.20 # Pin for beta stepper direction beta_en_pin 0.19 # Pin for beta enable beta_current 1.0 # Y stepper motor current y_axis_max_speed 30000 # mm/min gamma_step_pin 2.3 # Pin for gamma stepper step signal gamma_dir_pin 0.22 # Pin for gamma stepper direction gamma_en_pin 0.21 # Pin for gamma enable gamma_current 1.0 # Z stepper motor current z_axis_max_speed 300 # mm/min # Serial communications configuration ( baud rate default to 9600 if undefined ) uart0.baud_rate 115200 # Baud rate for the default hardware serial port second_usb_serial_enable false # This enables a second usb serial port (to have both pronterface and a terminal connected) #msd_disable false # disable the MSD (USB SDCARD) when set to true # Extruder module configuration extruder_module_enable true # Whether to activate the extruder module at all. All configuration is ignored if false extruder_steps_per_mm 140 # Steps per mm for extruder stepper extruder_default_feed_rate 600 # Default rate ( mm/minute ) for moves where only the extruder moves extruder_acceleration 500 # Acceleration in mm/sec^2, only used for retracts extruder_max_speed 1000 # mm/sec NOTE only used for retracts extruder_step_pin 2.0 # Pin for extruder step signal extruder_dir_pin 0.5 # Pin for extruder dir signal extruder_en_pin 0.4 # Pin for extruder enable signal delta_current 1.0 # Extruder stepper motor current # Laser module configuration laser_module_enable false # Whether to activate the laser module at all. All configuration is ignored if false. #laser_module_pin 2.7 # this pin will be PWMed to control the laser #laser_module_max_power 0.8 # this is the maximum duty cycle that will be applied to the laser #laser_module_tickle_power 0.0 # this duty cycle will be used for travel moves to keep the laser active without actually burning # Hotend temperature control configuration temperature_control.hotend.enable true # Whether to activate this ( "hotend" ) module at all. All configuration is ignored if false. temperature_control.hotend.thermistor_pin 0.24 # Pin for the thermistor to read temperature_control.hotend.heater_pin 2.5 # Pin that controls the heater temperature_control.hotend.thermistor EPCOS100K # see src/modules/tools/temperaturecontrol/TemperatureControl.cpp:64 for a list of valid thermistor names temperature_control.hotend.set_m_code 104 # temperature_control.hotend.set_and_wait_m_code 109 # temperature_control.hotend.designator T # temperature_control.hotend.p_factor 13.7 # temperature_control.hotend.i_factor 0.097 # temperature_control.hotend.d_factor 24 # temperature_control.bed.enable false # temperature_control.bed.thermistor_pin 0.23 # temperature_control.bed.heater_pin 2.7 # temperature_control.bed.thermistor Honeywell100K # see src/modules/tools/temperaturecontrol/TemperatureControl.cpp:64 for a list of valid thermistor names temperature_control.bed.set_m_code 140 # temperature_control.bed.set_and_wait_m_code 190 # temperature_control.bed.designator B # # Switch module for fan control switch.fan.enable true # switch.fan.input_on_command M106 # switch.fan.input_off_command M107 # switch.fan.output_pin 2.4 # switch.misc.enable false # switch.misc.input_on_command M42 # switch.misc.input_off_command M43 # switch.misc.output_pin 2.4 # # automatically toggle a switch at a specified temperature. Different ones of these may be defined to monitor different temperatures and switch different swithxes # useful to turn on a fan or water pump to cool the hotend #temperatureswitch.hotend.enable true # #temperatureswitch.hotend.designator T # first character of the temperature control designator to use as the temperature sensor to monitor #temperatureswitch.hotend.switch misc # select which switch to use, matches the name of the defined switch #temperatureswitch.hotend.threshold_temp 60.0 # temperature to turn on (if rising) or off the switch #temperatureswitch.hotend.heatup_poll 15 # poll heatup at 15 sec intervals #temperatureswitch.hotend.cooldown_poll 60 # poll cooldown at 60 sec intervals # Switch module for spindle control #switch.spindle.enable false # # Endstops endstops_enable true # the endstop module is enabled by default and can be disabled here #corexy_homing false # set to true if homing on a hbit or corexy alpha_min_endstop 1.24^ # add a ! to invert if endstop is NO connected to ground #alpha_max_endstop 1.24^ # alpha_homing_direction home_to_min # or set to home_to_max and set alpha_max alpha_min 0 # this gets loaded after homing when home_to_min is set alpha_max 200 # this gets loaded after homing when home_to_max is set beta_min_endstop 1.26^ # #beta_max_endstop 1.26^ # beta_homing_direction home_to_min # beta_min 0 # beta_max 200 # gamma_min_endstop 1.28^ # #gamma_max_endstop 1.28^ # gamma_homing_direction home_to_min # gamma_min 0 # gamma_max 200 # # optional enable limit switches, actions will stop if any enabled limit switch is triggered #alpha_limit_enable false # set to true to enable X min and max limit switches #beta_limit_enable false # set to true to enable Y min and max limit switches #gamma_limit_enable false # set to true to enable Z min and max limit switches #probe endstop #probe_pin 1.29 # optional pin for probe alpha_fast_homing_rate_mm_s 50 # feedrates in mm/second beta_fast_homing_rate_mm_s 50 # " gamma_fast_homing_rate_mm_s 4 # " alpha_slow_homing_rate_mm_s 25 # " beta_slow_homing_rate_mm_s 25 # " gamma_slow_homing_rate_mm_s 2 # " alpha_homing_retract_mm 5 # distance in mm beta_homing_retract_mm 5 # " gamma_homing_retract_mm 1 # " #endstop_debounce_count 100 # uncomment if you get noise on your endstops, default is 100 # optional Z probe zprobe.enable false # set to true to enable a zprobe zprobe.probe_pin 1.29!^ # pin probe is attached to if NC remove the ! zprobe.slow_feedrate 5 # mm/sec probe feed rate #zprobe.debounce_count 100 # set if noisy zprobe.fast_feedrate 100 # move feedrate mm/sec zprobe.probe_height 5 # how much above bed to start probe # associated with zprobe the leveling strategy to use #leveling-strategy.three-point-leveling.enable true # a leveling strategy that probes three points to define a plane and keeps the Z parallel to that plane #leveling-strategy.three-point-leveling.point1 100.0,0.0 # the first probe point (x,y) optional may be defined with M557 #leveling-strategy.three-point-leveling.point2 200.0,200.0 # the second probe point (x,y) #leveling-strategy.three-point-leveling.point3 0.0,200.0 # the third probe point (x,y) #leveling-strategy.three-point-leveling.home_first true # home the XY axis before probing #leveling-strategy.three-point-leveling.tolerance 0.03 # the probe tolerance in mm, anything less that this will be ignored, default is 0.03mm #leveling-strategy.three-point-leveling.probe_offsets 0,0,0 # the probe offsets from nozzle, must be x,y,z, default is no offset #leveling-strategy.three-point-leveling.save_plane false # set to true to allow the bed plane to be saved with M500 default is false # Pause button pause_button_enable true # # Panel panel.enable false # set to true to enable the panel code # Example for reprap discount GLCD # on glcd EXP1 is to left and EXP2 is to right, pin 1 is bottom left, pin 2 is top left etc. # +5v is EXP1 pin 10, Gnd is EXP1 pin 9 #panel.lcd reprap_discount_glcd # #panel.spi_channel 0 # pins 0.18, 0.15 ; GLCD EXP1 Pins 3,5 (MOSI, SCLK) #panel.spi_cs_pin 0.16 # spi chip select ; GLCD EXP1 Pin 4 #panel.encoder_a_pin 3.25!^ # encoder pin ; GLCD EXP2 Pin 3 #panel.encoder_b_pin 3.26!^ # encoder pin ; GLCD EXP2 Pin 5 #panel.click_button_pin 2.11!^ # click button ; GLCD EXP1 Pin 2 #panel.buzz_pin 1.31 # pin for buzzer ; GLCD EXP1 Pin 1 #panel.button_pause_pin 4.29^ # kill/pause ; GLCD EXP2 Pin 8 either #panel.back_button_pin 4.29!^ # back button ; GLCD EXP2 Pin 8 or panel.menu_offset 0 # some panels will need 1 here panel.alpha_jog_feedrate 6000 # x jogging feedrate in mm/min panel.beta_jog_feedrate 6000 # y jogging feedrate in mm/min panel.gamma_jog_feedrate 200 # z jogging feedrate in mm/min panel.hotend_temperature 185 # temp to set hotend when preheat is selected panel.bed_temperature 60 # temp to set bed when preheat is selected # Example of a custom menu entry, which will show up in the Custom entry. # NOTE _ gets converted to space in the menu and commands, | is used to separate multiple commands custom_menu.power_on.enable true # custom_menu.power_on.name Power_on # custom_menu.power_on.command M80 # custom_menu.power_off.enable true # custom_menu.power_off.name Power_off # custom_menu.power_off.command M81 # # Azteeg specific settings do not change currentcontrol_module_enable true # digipot_max_current 2.4 # max current digipot_factor 106.0 # factor for converting current to digipot value return_error_on_unhandled_gcode false #