moved wilson-bom.txt to -rs and added another for ts

diff --git a/doc/wilson-bom.txt b/doc/wilson-bom-rs.txt
similarity index 100%
rename from doc/wilson-bom.txt
rename to doc/wilson-bom-rs.txt

diff --git a/doc/wilson-bom-ts.txt b/doc/wilson-bom-ts.txt
new file mode 100644 (file)
index 0000000..34d1f26
--- /dev/null
+++ b/doc/wilson-bom-ts.txt
@@ -0,0 +1,84 @@
+Exported bom for Wilson TS from wilson-bom.ods 
+----------------------------------------------
+
+Item   Quantity        Length / Notes
+
+2020 Extrusions                
+Vertical frame piece (sides)                   2       400mm
+Horizontal frame piece (top and bottom)        2       320mm
+Y axis frame piece (TS only)                   2       415mm
+
+M8 Smooth Rods         
+X-Axis                                                                 2       380mm
+Y-Axis                                                                 2       415mm
+Z-Axis                                                                 2       350mm
+
+Threaded Rods          
+M5 threaded rod for Z axis                             2       325
+
+Belts & Pulleys                
+Y axis GT2 timing belt (w=6mm) 1       850mm
+X axis GT2 timing belt (w=6mm) 1       930mm
+GT2 pulley     2       Want diameter 16-20mm
+Nuts & Bolts           
+M10 nuts and washers   0       
+M5 x 10mm machine screw        44      
+M5 hex nut     2       
+M5 t slot nut  44      
+M4 x 20mm machine screw        6       
+M4 hex nut     6       
+M3 x 8mm machine screw 1       
+M3 x 10mm machine screw        11      
+M3 x 14mm machine screw        18      
+M3 x 30mm machine screw        7       
+M3 x 60mm machine screw        2       50mm?
+M3 hex nut     20?     This number is approximate
+M3 lock nut    7       
+M3 washer      20?     This number is approximate
+M8 x 20mm smooth rod or grub screw     1       
+M8 washers     5       For alignment of hobbed bolt
+M8 locknut     1       For extruder bolt
+Printed Parts – Required             
+X end idler    1       
+X end motor    1       
+X carriage     1       
+Y end idler    1       
+Y end motor    1       
+Y belt holder  1       
+Y axis bearing holder  4       for lm8uu bearings
+Z motor holder, left   1       
+Z motor holder, right  1       
+Z rod holder, left     1       
+Z rod holder, right    1       
+Z rear bracket 2       
+Z endstop holder       1       
+Frame brace    4       
+Idler bearing guide (pair)     2       
+Extruder body / idler set      1       
+Extruder big gear / small gear set     1       
+Extruder fan duct      1       
+Belt guides    4       (two belt guides, one for each 624 bearing)
+Printed Parts – Recommended          
+Electronics frame mount (for RAMPS)    1       
+Filament spool support (two pieces)    1       
+SMART display frame mount (two pieces) 1       
+Everything Else                
+NEMA17 Stepper motor   5       
+MDF board (6mm thick)  1       230mm by 230mm
+MK2 Heat bed   1       
+Glass bed      1       3mm borosilicate
+Controller (Mega/RAMPS, Rambo, etc)    1       
+Endstop (limit) switch 3       6mm x 10mm x 20mm
+LM8UU Linear bearing   12      
+608ZZ roller bearing   4       
+624 roller bearing     2       
+5mm to 5mm shaft couplers      2       Can also use vinyl tubing instead
+40mm x 40mm x 10mm fan 1       12V
+80mm x 80mm fan        1       For use with RAMPS frame mount
+Miniature zip ties     20      This number is approximate
+Extruder idler springs 2       High tension 
+Bed leveling springs   4       Lower tension
+Power Supply   1       Size appropriately for heat bed and extruder
+Hobbed bolt    1       Recommend airwolf3d
+Hot end        1       Recommend Jhead
+