Václav 'Ax' Hůla [Thu, 28 Feb 2013 14:38:19 +0000 (15:38 +0100)]
Tensioning X axis idler
Václav 'Ax' Hůla [Thu, 28 Feb 2013 14:29:11 +0000 (15:29 +0100)]
Fillet on motor end for rods > 8mm
Václav 'ax' Hůla [Thu, 28 Feb 2013 13:33:20 +0000 (05:33 -0800)]
Merge pull request #35 from AxTheB/master
Reduce visual artifacts with fillets
Václav 'Ax' Hůla [Thu, 28 Feb 2013 13:30:02 +0000 (14:30 +0100)]
Redice visual artifacts with fillets, fix idler assy axle hole
Václav 'ax' Hůla [Tue, 26 Feb 2013 08:28:57 +0000 (00:28 -0800)]
Merge pull request #34 from AxTheB/master
Increase Y corners height by 3mm
Václav 'Ax' Hůla [Tue, 26 Feb 2013 08:25:27 +0000 (09:25 +0100)]
Increase Y corners height by 3mm to get space under bed. It also
increases distance between smooth rod and frame
Václav 'ax' Hůla [Mon, 25 Feb 2013 15:05:07 +0000 (07:05 -0800)]
Merge pull request #33 from AxTheB/master
Fix motor mount block height depending on rod thickness, not z_delta
Václav 'Ax' Hůla [Mon, 25 Feb 2013 15:03:19 +0000 (16:03 +0100)]
Fix motor mount block height depending on rod thickness, not z_delta
Václav 'Ax' Hůla [Fri, 22 Feb 2013 14:12:26 +0000 (15:12 +0100)]
fix readme
Václav 'Ax' Hůla [Fri, 22 Feb 2013 14:05:42 +0000 (15:05 +0100)]
Add info about calibrating object to readme
Václav 'Ax' Hůla [Fri, 22 Feb 2013 10:48:58 +0000 (11:48 +0100)]
Belt holding teeth refactor config update
Václav 'Ax' Hůla [Fri, 22 Feb 2013 10:46:47 +0000 (11:46 +0100)]
Calibration testing part
Václav 'Ax' Hůla [Fri, 22 Feb 2013 10:46:24 +0000 (11:46 +0100)]
Belt holding teeth refactor
Václav 'Ax' Hůla [Tue, 19 Feb 2013 14:50:49 +0000 (15:50 +0100)]
Update rod dimensions to match EiNSTeiN's workshop bom
Václav 'Ax' Hůla [Tue, 19 Feb 2013 14:49:39 +0000 (15:49 +0100)]
Increase part separation to avoid touching for 12mm smooth rods
Václav 'Ax' Hůla [Mon, 18 Feb 2013 21:14:58 +0000 (22:14 +0100)]
Fix previous fix (left comments there)
Václav 'Ax' Hůla [Mon, 18 Feb 2013 20:33:25 +0000 (21:33 +0100)]
Fix Z axis
Václav 'Ax' Hůla [Sun, 17 Feb 2013 23:14:58 +0000 (00:14 +0100)]
dimensions.md updates
Václav 'Ax' Hůla [Sun, 17 Feb 2013 23:14:10 +0000 (00:14 +0100)]
Comments to boxframe.scad
Václav 'Ax' Hůla [Sun, 17 Feb 2013 22:32:37 +0000 (23:32 +0100)]
Assure there is enough space for belt under bearing in box x carriage
Václav 'Ax' Hůla [Sun, 17 Feb 2013 22:13:56 +0000 (23:13 +0100)]
Add doc/dimensions.md explaining correct rod lengths
Václav 'Ax' Hůla [Sun, 17 Feb 2013 22:12:55 +0000 (23:12 +0100)]
make extras to make models in extras [box only]
Václav 'Ax' Hůla [Sun, 17 Feb 2013 21:47:34 +0000 (22:47 +0100)]
Update gregs-wade to M3 hotswap screws
Václav 'Ax' Hůla [Fri, 15 Feb 2013 21:35:55 +0000 (22:35 +0100)]
fix: Move idler 1mm down on X, do its printable w. 10mm rods
Václav 'Ax' Hůla [Fri, 15 Feb 2013 21:11:02 +0000 (22:11 +0100)]
move bearing-guide.scad to inc/, add guides to x-end/y-drivetrain
Václav 'ax' Hůla [Fri, 15 Feb 2013 13:35:25 +0000 (05:35 -0800)]
Merge pull request #32 from AxTheB/new-bushing
New bushing
Václav 'Ax' Hůla [Thu, 14 Feb 2013 20:53:29 +0000 (21:53 +0100)]
Correcting previous statement
Václav 'Ax' Hůla [Thu, 14 Feb 2013 00:52:42 +0000 (01:52 +0100)]
PLA warning
Václav 'ax' Hůla [Mon, 11 Feb 2013 18:33:29 +0000 (10:33 -0800)]
Merge pull request #1 from kliment/new-bushing
Add tension adjuster to y idler
Kliment Yanev [Mon, 11 Feb 2013 18:27:14 +0000 (19:27 +0100)]
Add tension adjuster to y idler
Václav 'Ax' Hůla [Sun, 10 Feb 2013 23:08:48 +0000 (00:08 +0100)]
Add renders so its usable with OpenCSG rendering disabled, fix Z axis
screws
Václav 'Ax' Hůla [Sun, 10 Feb 2013 23:08:13 +0000 (00:08 +0100)]
Stepper shadow was in wrong place on Z
Václav 'Ax' Hůla [Sun, 10 Feb 2013 21:18:08 +0000 (22:18 +0100)]
polish
Václav 'Ax' Hůla [Sun, 10 Feb 2013 15:40:27 +0000 (16:40 +0100)]
Update manual to mention screws on bearings
Václav 'Ax' Hůla [Sat, 9 Feb 2013 22:22:04 +0000 (23:22 +0100)]
fix colouring
Václav 'Ax' Hůla [Sat, 9 Feb 2013 21:59:33 +0000 (22:59 +0100)]
Modified X carriage
Václav 'Ax' Hůla [Sat, 9 Feb 2013 19:39:44 +0000 (20:39 +0100)]
fix: make both xends;)
Václav 'Ax' Hůla [Sat, 9 Feb 2013 19:38:42 +0000 (20:38 +0100)]
Idler holder fixes
Václav 'Ax' Hůla [Thu, 7 Feb 2013 14:35:44 +0000 (15:35 +0100)]
readme updates
Václav 'Ax' Hůla [Thu, 7 Feb 2013 14:24:25 +0000 (15:24 +0100)]
Move clamping screw closer to bearing
Václav 'Ax' Hůla [Thu, 7 Feb 2013 13:59:59 +0000 (14:59 +0100)]
Merge branch 'master' of github.com:josefprusa/Prusa3 into new-bushing
Václav 'Ax' Hůla [Thu, 7 Feb 2013 13:56:13 +0000 (14:56 +0100)]
remove echo()
Václav 'Ax' Hůla [Thu, 7 Feb 2013 13:53:46 +0000 (14:53 +0100)]
Idler bearing rework
Václav 'Ax' Hůla [Mon, 4 Feb 2013 08:38:29 +0000 (09:38 +0100)]
Grow Y axis corners up when needed
Václav 'Ax' Hůla [Mon, 4 Feb 2013 08:37:32 +0000 (09:37 +0100)]
Longer bearings are held on both sides
Václav 'Ax' Hůla [Mon, 4 Feb 2013 08:36:12 +0000 (09:36 +0100)]
Better configuration of idler bearings
Joachim Glauche [Sun, 3 Feb 2013 13:25:06 +0000 (14:25 +0100)]
set extruder hole spacing to 30mm; made it thicker for extruders not to ram onto the boxframe x-end bolt; made it producing valid stls
Václav 'Ax' Hůla [Fri, 1 Feb 2013 18:47:16 +0000 (19:47 +0100)]
Move holes for Z axis single box (joaz)
Václav 'Ax' Hůla [Fri, 1 Feb 2013 14:18:31 +0000 (15:18 +0100)]
Fix for error in generated stl
Václav 'Ax' Hůla [Thu, 31 Jan 2013 10:13:55 +0000 (11:13 +0100)]
Update note for i_want_to_use_single_plate_dxf_and_make_my_z_weaker
Václav 'Ax' Hůla [Thu, 31 Jan 2013 09:59:52 +0000 (10:59 +0100)]
Change default for Z screw position when i_am_box = 0
Václav 'Ax' Hůla [Wed, 30 Jan 2013 13:40:10 +0000 (14:40 +0100)]
Move smooth rod to the board for thicker smooth rods
Václav 'Ax' Hůla [Wed, 30 Jan 2013 12:21:52 +0000 (13:21 +0100)]
fixes or single plate, z bottom is higher now
Václav 'Ax' Hůla [Wed, 30 Jan 2013 11:36:14 +0000 (12:36 +0100)]
calculate deltas for thick bearings
Václav 'Ax' Hůla [Wed, 30 Jan 2013 11:34:11 +0000 (12:34 +0100)]
lm10luu length fix
Václav 'Ax' Hůla [Wed, 30 Jan 2013 11:30:36 +0000 (12:30 +0100)]
foot moves when bearing holder enlarges, print only 2 Y carriage holders
for long bearings
Václav 'Ax' Hůla [Sun, 27 Jan 2013 20:06:39 +0000 (21:06 +0100)]
Increasing strength of z axis parts
Václav 'Ax' Hůla [Sun, 27 Jan 2013 20:06:02 +0000 (21:06 +0100)]
New bushing changes (unfinished)
Václav 'Ax' Hůla [Sun, 27 Jan 2013 14:39:32 +0000 (15:39 +0100)]
Fix default i_am_box
Václav 'Ax' Hůla [Sat, 26 Jan 2013 13:10:34 +0000 (14:10 +0100)]
box mounts updated to variable long threaded rod
Václav 'Ax' Hůla [Sat, 26 Jan 2013 13:06:30 +0000 (14:06 +0100)]
y corners adapted to new bushing config
Václav 'Ax' Hůla [Fri, 25 Jan 2013 20:09:16 +0000 (21:09 +0100)]
Remove #
Václav 'Ax' Hůla [Thu, 24 Jan 2013 13:42:35 +0000 (14:42 +0100)]
box config update
Václav 'Ax' Hůla [Thu, 24 Jan 2013 13:36:20 +0000 (14:36 +0100)]
Merge branch 'master' of github.com:josefprusa/Prusa3 into new-bushing
Václav 'Ax' Hůla [Thu, 24 Jan 2013 13:34:36 +0000 (14:34 +0100)]
z axis rework, inspired by single-plate Z
Václav 'Ax' Hůla [Thu, 24 Jan 2013 13:34:00 +0000 (14:34 +0100)]
Simplify x end nut trap
Shane Graber [Tue, 22 Jan 2013 23:45:21 +0000 (18:45 -0500)]
corrected frame for mini
Alessandro Ranellucci [Mon, 21 Jan 2013 08:05:20 +0000 (00:05 -0800)]
Merge pull request #28 from awratten/patch-1
Create Prusa3_SC10UU-v1.dxf
awratten [Mon, 21 Jan 2013 05:52:39 +0000 (21:52 -0800)]
Create Prusa3_SC10UU-v1.dxf
For SC10UU Linear bearings
Václav 'Ax' Hůla [Sun, 20 Jan 2013 22:18:33 +0000 (23:18 +0100)]
away with the z constraint, its not doing any good
Václav 'Ax' Hůla [Sun, 20 Jan 2013 21:50:10 +0000 (22:50 +0100)]
Move bushing config
Václav 'Ax' Hůla [Sun, 20 Jan 2013 21:48:19 +0000 (22:48 +0100)]
Merge remote-tracking branch 'upstream/master' into new-bushing
Václav 'Ax' Hůla [Sun, 20 Jan 2013 21:42:30 +0000 (22:42 +0100)]
Config file with different bearings and bushings
Shane Graber [Wed, 16 Jan 2013 03:12:09 +0000 (22:12 -0500)]
for 6mm lasercut wood. initial import.
Shane Graber [Wed, 16 Jan 2013 03:10:44 +0000 (22:10 -0500)]
for 6mm lasercut wood. initial commit.
Václav 'Ax' Hůla [Tue, 15 Jan 2013 15:47:03 +0000 (16:47 +0100)]
remove #
Kaz Walker [Thu, 10 Jan 2013 11:09:37 +0000 (04:09 -0700)]
Added License file (GPL v3) to repo.
Alessandro Ranellucci [Wed, 9 Jan 2013 19:00:18 +0000 (20:00 +0100)]
More mini files!
Alessandro Ranellucci [Wed, 9 Jan 2013 18:59:51 +0000 (19:59 +0100)]
Allow STL files from outside box_frame and single_plate
Alessandro Ranellucci [Wed, 9 Jan 2013 18:57:43 +0000 (19:57 +0100)]
New mini!
Alessandro Ranellucci [Wed, 9 Jan 2013 18:53:15 +0000 (19:53 +0100)]
Remove frame-mount.scad, not needed anymore. #21
Alessandro Ranellucci [Wed, 9 Jan 2013 18:25:34 +0000 (19:25 +0100)]
Updated DXF file with 10mm threaded rods
Alessandro Ranellucci [Wed, 9 Jan 2013 16:49:35 +0000 (17:49 +0100)]
Merging jo-final to single_plate/
Alessandro Ranellucci [Wed, 9 Jan 2013 16:29:21 +0000 (17:29 +0100)]
Merge remote branch 'alexrj/jo-final' into HEAD
Conflicts:
src/compact-extruder.scad
Alessandro Ranellucci [Wed, 9 Jan 2013 16:23:46 +0000 (17:23 +0100)]
Move everything to box_frame/
Kaz Walker [Wed, 9 Jan 2013 04:45:12 +0000 (21:45 -0700)]
Add GT2 to configuration.scad.dist, closes #19
Václav 'Ax' Hůla [Sun, 6 Jan 2013 15:20:38 +0000 (16:20 +0100)]
linear_preclean function to make sure there is empty space for
bushings/bearings (fixes y axis bearings)
Václav 'Ax' Hůla [Thu, 3 Jan 2013 14:45:12 +0000 (15:45 +0100)]
update x-end to new bushing.scad - still needs more work to allow bigger
bearings
Václav 'Ax' Hůla [Thu, 3 Jan 2013 14:44:40 +0000 (15:44 +0100)]
Update x-carriage to new bushing.scad
Václav 'Ax' Hůla [Thu, 3 Jan 2013 14:43:07 +0000 (15:43 +0100)]
bushing rewrite
Václav 'Ax' Hůla [Thu, 20 Dec 2012 09:30:28 +0000 (10:30 +0100)]
Let the board_thickness affect y-axis-corner height
Václav 'Ax' Hůla [Thu, 20 Dec 2012 09:24:36 +0000 (10:24 +0100)]
Merge branch 'master' of github.com:josefprusa/Prusa3
kliment [Sun, 16 Dec 2012 10:21:21 +0000 (02:21 -0800)]
Merge pull request #18 from cymerio/master
New scad file with all the parts and vitamins
David Rubio [Sat, 15 Dec 2012 22:42:21 +0000 (23:42 +0100)]
Fixed bottom nuts separation.
Václav 'Ax' Hůla [Fri, 14 Dec 2012 22:41:04 +0000 (23:41 +0100)]
Z constraining bearing touches
Václav 'Ax' Hůla [Sat, 8 Dec 2012 18:50:58 +0000 (19:50 +0100)]
Option to disable fillets
Václav 'Ax' Hůla [Sat, 8 Dec 2012 18:04:56 +0000 (19:04 +0100)]
Merge remote-tracking branch 'upstream/master'
Conflicts:
bushing.scad
x-carriage.scad
x-end.scad
Václav 'Ax' Hůla [Sat, 8 Dec 2012 17:41:57 +0000 (18:41 +0100)]
use M10 threaded rods in Y direction
Václav 'Ax' Hůla [Sat, 8 Dec 2012 17:40:33 +0000 (18:40 +0100)]
Use correct bushing/bearing negative
Václav 'Ax' Hůla [Sat, 8 Dec 2012 17:38:20 +0000 (18:38 +0100)]
Added notes and some