Joachim Glauche [Sat, 4 Aug 2012 21:07:13 +0000 (23:07 +0200)]
made Y idler configurable by bearing size, also made it square for perfect print results without support
Nathan Zadoks [Wed, 25 Jul 2012 13:13:01 +0000 (15:13 +0200)]
Updated belt clamp, it was too large.
Nathan Zadoks [Mon, 23 Jul 2012 15:38:03 +0000 (17:38 +0200)]
X carriage adjustable belt clamp \o/
Joachim Glauche [Mon, 23 Jul 2012 10:27:48 +0000 (12:27 +0200)]
made outside wall a 1mm thicker for more stability
Joachim Glauche [Mon, 23 Jul 2012 10:25:11 +0000 (12:25 +0200)]
increased pushfit rod size (came out way too small)) and z rod hole size
Joachim Glauche [Sat, 21 Jul 2012 18:02:01 +0000 (20:02 +0200)]
set default for nema 17 motor to 24 to get correctly sized bolt holes
Nathan Zadoks [Fri, 13 Jul 2012 06:56:19 +0000 (08:56 +0200)]
Improved Y bottom plate mount code a bit.
vlnofka [Wed, 11 Jul 2012 08:48:02 +0000 (10:48 +0200)]
More space for extruder motor.
vlnofka [Sun, 8 Jul 2012 20:38:35 +0000 (22:38 +0200)]
Now motor should not collide with Z plate.
Idler uses m4 screws.
Motor mount holes are now rotaded.
Now we have sunken extruder mounting screws.
Joachim Glauche [Sat, 7 Jul 2012 19:24:30 +0000 (21:24 +0200)]
make hole for Z rod bigger to actually fit through
Joachim Glauche [Sat, 7 Jul 2012 19:16:20 +0000 (21:16 +0200)]
Merge branch 'master' of github.com:josefprusa/Prusa3
Nathan Zadoks [Sat, 7 Jul 2012 15:32:39 +0000 (17:32 +0200)]
fixed up Z axis nut trap direction and dimensions
Joachim Glauche [Fri, 6 Jul 2012 10:02:46 +0000 (12:02 +0200)]
more space for belts
Joachim Glauche [Fri, 6 Jul 2012 09:57:25 +0000 (11:57 +0200)]
more space for belts to slip in
Joachim Glauche [Wed, 4 Jul 2012 18:43:46 +0000 (20:43 +0200)]
made a y to bottom plate mounting part
Joachim Glauche [Tue, 3 Jul 2012 14:04:58 +0000 (16:04 +0200)]
fix charset
Joachim Glauche [Tue, 3 Jul 2012 11:43:06 +0000 (13:43 +0200)]
made linear bearing channels 5mm shorter to end at the same height as the main body
Václav 'Ax' Hůla [Mon, 2 Jul 2012 10:24:53 +0000 (12:24 +0200)]
Merge branch 'master' of github.com:josefprusa/Prusa3
Václav 'Ax' Hůla [Mon, 2 Jul 2012 09:58:33 +0000 (11:58 +0200)]
z-axis can be mounted by 2 crews from front or one front/one side screw.
Toni Frost [Sat, 30 Jun 2012 10:02:01 +0000 (19:32 +0930)]
complete-printer - need updates to the config dist
Toni Frost [Sat, 30 Jun 2012 09:45:38 +0000 (19:15 +0930)]
complete-printer - fix y axis and nuts
Toni Frost [Sat, 30 Jun 2012 09:05:48 +0000 (18:35 +0930)]
more complete printer updates
Toni Frost [Sat, 30 Jun 2012 06:23:21 +0000 (15:53 +0930)]
updates for the assembled printer
Toni Frost [Sat, 30 Jun 2012 03:08:48 +0000 (12:38 +0930)]
typos in includes
Václav 'Ax' Hůla [Thu, 28 Jun 2012 16:45:40 +0000 (18:45 +0200)]
Some more configurable dimensions
vlnofka [Tue, 26 Jun 2012 21:01:00 +0000 (23:01 +0200)]
Modified Greg's Wade extruder
Václav 'Ax' Hůla [Tue, 26 Jun 2012 19:47:36 +0000 (21:47 +0200)]
Fixed typo in filename
Václav 'Ax' Hůla [Tue, 26 Jun 2012 19:13:49 +0000 (21:13 +0200)]
Hotswap carriage
Václav 'Ax' Hůla [Mon, 25 Jun 2012 22:07:52 +0000 (00:07 +0200)]
parametric x axis distance creeps in
Václav 'Ax' Hůla [Mon, 25 Jun 2012 16:19:30 +0000 (18:19 +0200)]
fix hardcoded 16 in fillet
Joachim Glauche [Wed, 20 Jun 2012 08:56:19 +0000 (10:56 +0200)]
remove the second hole, make parts smaller
Joachim Glauche [Wed, 20 Jun 2012 08:30:16 +0000 (10:30 +0200)]
made the z mounts parametric according to board size
Václav 'Ax' Hůla [Tue, 19 Jun 2012 20:40:39 +0000 (22:40 +0200)]
x-ends: make far wall thicker a bit
Václav 'Ax' Hůla [Tue, 19 Jun 2012 20:03:31 +0000 (22:03 +0200)]
Add readme to output dir
Václav 'Ax' Hůla [Tue, 19 Jun 2012 20:02:02 +0000 (22:02 +0200)]
Merge branch 'fillet'
Kliment Yanev [Mon, 18 Jun 2012 14:40:13 +0000 (16:40 +0200)]
Finished y axis instructions
Kliment Yanev [Sat, 16 Jun 2012 21:05:35 +0000 (23:05 +0200)]
Merge branch 'fillet' of github.com:josefprusa/Prusa3 into fillet
Kliment Yanev [Sat, 16 Jun 2012 21:04:33 +0000 (23:04 +0200)]
Fix shadow motor orientation in y motor holder, wrote most of y axis docs, generated more images.
John Yang [Fri, 15 Jun 2012 18:31:14 +0000 (14:31 -0400)]
folding clamp holder for mounting Y frame to single board for storage or transport
Kliment Yanev [Thu, 14 Jun 2012 14:08:14 +0000 (16:08 +0200)]
Merge branch 'fillet' of github.com:josefprusa/Prusa3 into fillet
Kliment Yanev [Thu, 14 Jun 2012 14:07:43 +0000 (16:07 +0200)]
Move manual to doc folder
Václav 'Ax' Hůla [Thu, 14 Jun 2012 14:04:03 +0000 (16:04 +0200)]
more doc moving
Kliment Yanev [Thu, 14 Jun 2012 13:44:58 +0000 (15:44 +0200)]
Move doc files to doc directory
Kliment Yanev [Thu, 14 Jun 2012 12:57:47 +0000 (14:57 +0200)]
Initial manual sketch, frame assembly images and source images were generated from.
Václav 'Ax' Hůla [Wed, 13 Jun 2012 13:16:02 +0000 (15:16 +0200)]
Fix z-axis thickness scaling, make it thicker by default
Václav 'Ax' Hůla [Wed, 13 Jun 2012 12:45:51 +0000 (14:45 +0200)]
dump the damn nuttraps
Václav 'Ax' Hůla [Wed, 13 Jun 2012 07:04:07 +0000 (09:04 +0200)]
idler fix
Václav 'Ax' Hůla [Tue, 12 Jun 2012 20:28:58 +0000 (22:28 +0200)]
Thinner bearing-guide walls
Václav 'Ax' Hůla [Tue, 12 Jun 2012 17:54:57 +0000 (19:54 +0200)]
Merge branch 'fillet' of github.com:josefprusa/Prusa3 into fillet
Václav 'Ax' Hůla [Tue, 12 Jun 2012 17:54:09 +0000 (19:54 +0200)]
Give motor some breathing space
Václav 'Ax' Hůla [Tue, 12 Jun 2012 17:48:02 +0000 (19:48 +0200)]
two screw hole
vlnofka [Mon, 11 Jun 2012 19:56:48 +0000 (21:56 +0200)]
Better NEMA17 dummy (with flange and shaft)
Václav 'Ax' Hůla [Mon, 11 Jun 2012 01:26:07 +0000 (03:26 +0200)]
linear bearings dont need springy housing
Václav 'Ax' Hůla [Mon, 11 Jun 2012 01:16:47 +0000 (03:16 +0200)]
Even smaller floating bearing, lifted ends for firmer grasp.
Václav 'Ax' Hůla [Mon, 11 Jun 2012 00:03:36 +0000 (02:03 +0200)]
Merge branch 'fillet' of github.com:josefprusa/Prusa3 into fillet
Václav 'Ax' Hůla [Sun, 10 Jun 2012 23:55:01 +0000 (01:55 +0200)]
reduce springiness, clean-up
Václav 'Ax' Hůla [Sat, 9 Jun 2012 22:26:38 +0000 (00:26 +0200)]
Make floating bearing less springy and smaller
vlnofka [Thu, 7 Jun 2012 21:48:45 +0000 (23:48 +0200)]
Fixed syntax error
John Yang [Thu, 7 Jun 2012 13:00:04 +0000 (09:00 -0400)]
decreased padding width of lm8uu bearing to have tighter fit
John Yang [Thu, 7 Jun 2012 12:58:44 +0000 (08:58 -0400)]
adjusted idler hole to closer match beaing radius, increased width of belt hole to bette fit 608 bearing within bearing guide
Nathan Zadoks [Thu, 7 Jun 2012 11:46:15 +0000 (13:46 +0200)]
make output dir automatically
Václav 'Ax' Hůla [Thu, 7 Jun 2012 09:50:39 +0000 (11:50 +0200)]
Address #3
John Yang [Thu, 7 Jun 2012 03:36:11 +0000 (23:36 -0400)]
added in the bearing_type variable with the default value. comment was in the file, but the example/default variable declaration was missing
John Yang [Thu, 7 Jun 2012 03:05:00 +0000 (23:05 -0400)]
make idler mount hole use config size for idler instead of hard coded value. also moved so m8 hole would not be so close to edge.
John Yang [Thu, 7 Jun 2012 02:28:02 +0000 (22:28 -0400)]
lme8uu and lm8uu dimensions inverted fo bearing calculations
Václav 'Ax' Hůla [Wed, 6 Jun 2012 14:30:16 +0000 (16:30 +0200)]
bearing fixes... hopefully it has all correct dimensions now.
Václav 'Ax' Hůla [Wed, 6 Jun 2012 09:31:11 +0000 (11:31 +0200)]
Add credit to fillet() author
Václav 'Ax' Hůla [Wed, 6 Jun 2012 09:30:24 +0000 (11:30 +0200)]
linear bearing has minimum size now, fixed fillet.
Václav 'Ax' Hůla [Tue, 5 Jun 2012 16:42:08 +0000 (18:42 +0200)]
now we have Makefile, ho ho ho!
Václav 'Ax' Hůla [Tue, 5 Jun 2012 13:47:43 +0000 (15:47 +0200)]
Fix bearing sizes
Václav 'Ax' Hůla [Mon, 4 Jun 2012 12:57:19 +0000 (14:57 +0200)]
heptagonal nema17 holes, yay!
Václav 'Ax' Hůla [Mon, 4 Jun 2012 11:06:19 +0000 (13:06 +0200)]
Shorter screw for x-end stepper
Václav 'Ax' Hůla [Mon, 4 Jun 2012 11:04:28 +0000 (13:04 +0200)]
ignore .gcode files too
Václav 'Ax' Hůla [Mon, 4 Jun 2012 11:03:10 +0000 (13:03 +0200)]
give nema17 screw longer head shaft
Václav 'Ax' Hůla [Mon, 4 Jun 2012 09:24:21 +0000 (11:24 +0200)]
Header change, minor fiddling with bushings, x-carriage refactor part I
Also, I removed link to prusadjs.cz, as the blog is 2 years dead.
Václav 'Ax' Hůla [Sun, 3 Jun 2012 18:50:55 +0000 (20:50 +0200)]
size clenaup too
Václav 'Ax' Hůla [Sun, 3 Jun 2012 18:45:19 +0000 (20:45 +0200)]
cleanup: remove size argument name from cubes
Václav 'Ax' Hůla [Sun, 3 Jun 2012 17:36:11 +0000 (19:36 +0200)]
tree-point mount of x motor
Václav 'Ax' Hůla [Sun, 3 Jun 2012 01:51:00 +0000 (03:51 +0200)]
purge redundant <inc/functions.scad>
Václav 'Ax' Hůla [Sun, 3 Jun 2012 01:47:11 +0000 (03:47 +0200)]
nushing.scad rework. Y and Z axis change as in configuraion.scad
Václav 'Ax' Hůla [Sat, 2 Jun 2012 18:37:23 +0000 (20:37 +0200)]
LARGE reformat (tabs to 4 spaces everywhere, cleaning of rotatate and
translate arguments).
Václav 'Ax' Hůla [Fri, 1 Jun 2012 23:18:24 +0000 (01:18 +0200)]
Bushing.scad rewrite, part 1
Václav 'Ax' Hůla [Fri, 1 Jun 2012 23:18:08 +0000 (01:18 +0200)]
More eyecandy
Václav 'Ax' Hůla [Fri, 1 Jun 2012 20:31:12 +0000 (22:31 +0200)]
Extract printer preview, add colors
Václav 'Ax' Hůla [Fri, 1 Jun 2012 20:27:30 +0000 (22:27 +0200)]
Added desired layer width and WoT to README
Václav 'Ax' Hůla [Fri, 1 Jun 2012 17:41:24 +0000 (19:41 +0200)]
Y motor holder has proper shadow stepper now
Václav 'Ax' Hůla [Fri, 1 Jun 2012 15:30:12 +0000 (17:30 +0200)]
rename nema->nema17, put shadow bearing on idlerholder
Václav 'Ax' Hůla [Fri, 1 Jun 2012 15:04:51 +0000 (17:04 +0200)]
more parametric idler stuff
Václav 'Ax' Hůla [Fri, 1 Jun 2012 13:20:08 +0000 (15:20 +0200)]
Changed idler to bearing-guide from i2, parametrised
Václav 'Ax' Hůla [Fri, 1 Jun 2012 11:35:36 +0000 (13:35 +0200)]
Start of README
Václav 'Ax' Hůla [Fri, 1 Jun 2012 11:22:33 +0000 (13:22 +0200)]
LARGE scale cleanup
Václav 'Ax' Hůla [Fri, 1 Jun 2012 09:18:10 +0000 (11:18 +0200)]
Fix for missing holes in older openscads
Václav 'Ax' Hůla [Thu, 31 May 2012 06:31:55 +0000 (08:31 +0200)]
open top Y corners
Václav 'Ax' Hůla [Wed, 30 May 2012 19:24:28 +0000 (21:24 +0200)]
round bottom
Václav 'Ax' Hůla [Wed, 30 May 2012 18:39:04 +0000 (20:39 +0200)]
stepper on bridges
Václav 'Ax' Hůla [Wed, 30 May 2012 08:20:01 +0000 (10:20 +0200)]
I really think that module idler was of no use.
Václav 'Ax' Hůla [Wed, 30 May 2012 08:10:04 +0000 (10:10 +0200)]
fix last commit
Václav 'Ax' Hůla [Wed, 30 May 2012 00:04:25 +0000 (02:04 +0200)]
Refactored y frame. Split in two files.
Václav 'Ax' Hůla [Tue, 29 May 2012 23:58:13 +0000 (01:58 +0200)]
Make teeth of y-belt-holder wider so its more usable
Václav 'Ax' Hůla [Tue, 29 May 2012 23:52:25 +0000 (01:52 +0200)]
y belt holder with round corners and teeth info from config