1 # NOTE Lines must not exceed 132 characters
2 # Robot module configurations : general handling of movement G-codes and slicing into moves
3 default_feed_rate 4000 # Default rate ( mm/minute ) for G1/G2/G3 moves
4 default_seek_rate 4000 # Default rate ( mm/minute ) for G0 moves
5 mm_per_arc_segment 0.5 # Arcs are cut into segments ( lines ), this is the length for
6 # these segments. Smaller values mean more resolution,
7 # higher values mean faster computation
8 #mm_per_line_segment 5 # Lines can be cut into segments ( not usefull with cartesian
9 # coordinates robots ).
11 # Arm solution configuration : Cartesian robot. Translates mm positions into stepper positions
12 alpha_steps_per_mm 80 # Steps per mm for alpha stepper
13 beta_steps_per_mm 80 # Steps per mm for beta stepper
14 gamma_steps_per_mm 1600 # Steps per mm for gamma stepper
16 # Planner module configuration : Look-ahead and acceleration configuration
17 planner_queue_size 32 # DO NOT CHANGE THIS UNLESS YOU KNOW EXACTLY WHAT YOU ARE DOING
18 acceleration 3000 # Acceleration in mm/second/second.
19 #z_acceleration 500 # Acceleration for Z only moves in mm/s^2, 0 uses acceleration which is the default. DO NOT SET ON A DELTA
20 acceleration_ticks_per_second 1000 # Number of times per second the speed is updated
21 junction_deviation 0.05 # Similar to the old "max_jerk", in millimeters,
22 # see https://github.com/grbl/grbl/blob/master/planner.c
23 # and https://github.com/grbl/grbl/wiki/Configuring-Grbl-v0.8
24 # Lower values mean being more careful, higher values means being
25 # faster and have more jerk
26 #z_junction_deviation 0.0 # for Z only moves, -1 uses junction_deviation, zero disables junction_deviation on z moves DO NOT SET ON A DELTA
27 #minimum_planner_speed 0.0 # sets the minimum planner speed in mm/sec
29 # Stepper module configuration
30 microseconds_per_step_pulse 1 # Duration of step pulses to stepper drivers, in microseconds
31 base_stepping_frequency 100000 # Base frequency for stepping
33 # Cartesian axis speed limits
34 x_axis_max_speed 30000 # mm/min
35 y_axis_max_speed 30000 # mm/min
36 z_axis_max_speed 300 # mm/min
38 # Stepper module pins ( ports, and pin numbers, appending "!" to the number will invert a pin )
39 alpha_step_pin 2.0 # Pin for alpha stepper step signal
40 alpha_dir_pin 0.5 # Pin for alpha stepper direction
41 alpha_en_pin 0.4 # Pin for alpha enable pin
42 alpha_current 1.5 # X stepper motor current
43 alpha_max_rate 30000.0 # mm/min
45 beta_step_pin 2.1 # Pin for beta stepper step signal
46 beta_dir_pin 0.11 # Pin for beta stepper direction
47 beta_en_pin 0.10 # Pin for beta enable
48 beta_current 1.5 # Y stepper motor current
49 beta_max_rate 30000.0 # mm/min
51 gamma_step_pin 2.2 # Pin for gamma stepper step signal
52 gamma_dir_pin 0.20 # Pin for gamma stepper direction
53 gamma_en_pin 0.19 # Pin for gamma enable
54 gamma_current 1.5 # Z stepper motor current
55 gamma_max_rate 300.0 # mm/min
57 # Serial communications configuration ( baud rate default to 9600 if undefined )
58 uart0.baud_rate 115200 # Baud rate for the default hardware serial port
59 second_usb_serial_enable false # This enables a second usb serial port (to have both pronterface
60 # and a terminal connected)
61 #leds_disable true # disable using leds after config loaded
62 #play_led_disable true # disable the play led
63 pause_button_enable true # Pause button enable
64 #pause_button_pin 2.12 # pause button pin. default is P2.12
65 #kill_button_enable false # set to true to enable a kill button
66 #kill_button_pin 2.12 # kill button pin. default is same as pause button 2.12 (2.11 is another good choice)
67 #msd_disable false # disable the MSD (USB SDCARD) when set to true (needs special binary)
68 #dfu_enable false # for linux developers, set to true to enable DFU
70 # Extruder module configuration
71 extruder.hotend.enable true # Whether to activate the extruder module at all. All configuration is ignored if false
72 extruder.hotend.steps_per_mm 140 # Steps per mm for extruder stepper
73 extruder.hotend.default_feed_rate 600 # Default rate ( mm/minute ) for moves where only the extruder moves
74 extruder.hotend.acceleration 500 # Acceleration for the stepper motor mm/sec²
75 extruder.hotend.max_speed 50 # mm/s
77 extruder.hotend.step_pin 2.3 # Pin for extruder step signal
78 extruder.hotend.dir_pin 0.22 # Pin for extruder dir signal
79 extruder.hotend.en_pin 0.21 # Pin for extruder enable signal
82 #extruder.hotend.x_offset 0 # x offset from origin in mm
83 #extruder.hotend.y_offset 0 # y offset from origin in mm
84 #extruder.hotend.z_offset 0 # z offset from origin in mm
86 # firmware retract settings when using G10/G11, these are the defaults if not defined, must be defined for each extruder if not using the defaults
87 #extruder.hotend.retract_length 3 # retract length in mm
88 #extruder.hotend.retract_feedrate 45 # retract feedrate in mm/sec
89 #extruder.hotend.retract_recover_length 0 # additional length for recover
90 #extruder.hotend.retract_recover_feedrate 8 # recover feedrate in mm/sec (should be less than retract feedrate)
91 #extruder.hotend.retract_zlift_length 0 # zlift on retract in mm, 0 disables
92 #extruder.hotend.retract_zlift_feedrate 6000 # zlift feedrate in mm/min (Note mm/min NOT mm/sec)
94 delta_current 1.5 # First extruder stepper motor current
96 # Second extruder module configuration
97 #extruder.hotend2.enable true # Whether to activate the extruder module at all. All configuration is ignored if false
98 #extruder.hotend2.steps_per_mm 140 # Steps per mm for extruder stepper
99 #extruder.hotend2.default_feed_rate 600 # Default rate ( mm/minute ) for moves where only the extruder moves
100 #extruder.hotend2.acceleration 500 # Acceleration for the stepper motor, as of 0.6, arbitrary ratio
101 #extruder.hotend2.max_speed 50 # mm/s
103 #extruder.hotend2.step_pin 2.8 # Pin for extruder step signal
104 #extruder.hotend2.dir_pin 2.13 # Pin for extruder dir signal
105 #extruder.hotend2.en_pin 4.29 # Pin for extruder enable signal
107 #extruder.hotend2.x_offset 0 # x offset from origin in mm
108 #extruder.hotend2.y_offset 25.0 # y offset from origin in mm
109 #extruder.hotend2.z_offset 0 # z offset from origin in mm
110 #epsilon_current 1.5 # Second extruder stepper motor current
113 # Laser module configuration
114 laser_module_enable false # Whether to activate the laser module at all. All configuration is
116 #laser_module_pin 2.5 # this pin will be PWMed to control the laser. Only P2.0 - P2.5, P1.18, P1.20, P1.21, P1.23, P1.24, P1.26, P3.25, P3.26
117 # can be used since laser requires hardware PWM
118 #laser_module_maximum_power 1.0 # this is the maximum duty cycle that will be applied to the laser
119 #laser_module_minimum_power 0.0 # This is a value just below the minimum duty cycle that keeps the laser
120 # active without actually burning.
121 #laser_module_default_power 0.8 # This is the default laser power that will be used for cuts if a power has not been specified. The value is a scale between
122 # the maximum and minimum power levels specified above
123 #laser_module_pwm_period 20 # this sets the pwm frequency as the period in microseconds
125 # Hotend temperature control configuration
126 temperature_control.hotend.enable true # Whether to activate this ( "hotend" ) module at all.
127 # All configuration is ignored if false.
128 temperature_control.hotend.thermistor_pin 0.23 # Pin for the thermistor to read
129 temperature_control.hotend.heater_pin 2.7 # Pin that controls the heater, set to nc if a readonly thermistor is being defined
130 temperature_control.hotend.thermistor EPCOS100K # see http://smoothieware.org/temperaturecontrol#toc5
131 #temperature_control.hotend.beta 4066 # or set the beta value
132 temperature_control.hotend.set_m_code 104 #
133 temperature_control.hotend.set_and_wait_m_code 109 #
134 temperature_control.hotend.designator T #
135 #temperature_control.hotend.max_temp 250 # Set maximum temperature
136 #temperature_control.hotend.min_temp 0 # Set minimum temperature - Will prevent heating below if set
138 #temperature_control.hotend.p_factor 13.7 # permanently set the PID values after an auto pid
139 #temperature_control.hotend.i_factor 0.097 #
140 #temperature_control.hotend.d_factor 24 #
142 #temperature_control.hotend.max_pwm 64 # max pwm, 64 is a good value if driving a 12v resistor with 24v.
144 # Hotend2 temperature control configuration
145 #temperature_control.hotend2.enable true # Whether to activate this ( "hotend" ) module at all.
146 # All configuration is ignored if false.
148 #temperature_control.hotend2.thermistor_pin 0.25 # Pin for the thermistor to read
149 #temperature_control.hotend2.heater_pin 1.23 # Pin that controls the heater
150 #temperature_control.hotend2.thermistor EPCOS100K # see http://smoothieware.org/temperaturecontrol#toc5
151 ##temperature_control.hotend2.beta 4066 # or set the beta value
152 #temperature_control.hotend2.set_m_code 884 #
153 #temperature_control.hotend2.set_and_wait_m_code 889 #
154 #temperature_control.hotend2.designator T1 #
156 #temperature_control.hotend2.p_factor 13.7 # permanently set the PID values after an auto pid
157 #temperature_control.hotend2.i_factor 0.097 #
158 #temperature_control.hotend2.d_factor 24 #
160 #temperature_control.hotend2.max_pwm 64 # max pwm, 64 is a good value if driving a 12v resistor with 24v.
162 temperature_control.bed.enable true #
163 temperature_control.bed.thermistor_pin 0.24 #
164 temperature_control.bed.heater_pin 2.5 #
165 temperature_control.bed.thermistor Honeywell100K # see http://smoothieware.org/temperaturecontrol#toc5
166 #temperature_control.bed.beta 3974 # or set the beta value
168 temperature_control.bed.set_m_code 140 #
169 temperature_control.bed.set_and_wait_m_code 190 #
170 temperature_control.bed.designator B #
172 #temperature_control.bed.bang_bang false # set to true to use bang bang control rather than PID
173 #temperature_control.bed.hysteresis 2.0 # set to the temperature in degrees C to use as hysteresis
174 # when using bang bang
176 # Switch module for fan control
177 switch.fan.enable true #
178 switch.fan.input_on_command M106 #
179 switch.fan.input_off_command M107 #
180 switch.fan.output_pin 2.6 #
181 switch.fan.output_type pwm # pwm output settable with S parameter in the input_on_comand
182 #switch.fan.max_pwm 255 # set max pwm for the pin default is 255
184 #switch.misc.enable true #
185 #switch.misc.input_on_command M42 #
186 #switch.misc.input_off_command M43 #
187 #switch.misc.output_pin 2.4 #
188 #switch.misc.output_type digital # just an on or off pin
190 # automatically toggle a switch at a specified temperature. Different ones of these may be defined to monitor different temperatures and switch different swithxes
191 # useful to turn on a fan or water pump to cool the hotend
192 #temperatureswitch.hotend.enable true #
193 #temperatureswitch.hotend.designator T # first character of the temperature control designator to use as the temperature sensor to monitor
194 #temperatureswitch.hotend.switch misc # select which switch to use, matches the name of the defined switch
195 #temperatureswitch.hotend.threshold_temp 60.0 # temperature to turn on (if rising) or off the switch
196 #temperatureswitch.hotend.heatup_poll 15 # poll heatup at 15 sec intervals
197 #temperatureswitch.hotend.cooldown_poll 60 # poll cooldown at 60 sec intervals
199 # Switch module for spindle control
200 #switch.spindle.enable false #
203 endstops_enable true # the endstop module is enabled by default and can be disabled here
204 #corexy_homing false # set to true if homing on a hbit or corexy
205 alpha_min_endstop 1.24^ # add a ! to invert if endstop is NO connected to ground
206 alpha_max_endstop 1.25^ # NOTE set to nc if this is not installed
207 alpha_homing_direction home_to_min # or set to home_to_max and set alpha_max
208 alpha_min 0 # this gets loaded after homing when home_to_min is set
209 alpha_max 200 # this gets loaded after homing when home_to_max is set
210 beta_min_endstop 1.26^ #
211 beta_max_endstop 1.27^ #
212 beta_homing_direction home_to_min #
215 gamma_min_endstop 1.28^ #
216 gamma_max_endstop 1.29^ #
217 gamma_homing_direction home_to_min #
221 # optional order in which axis will home, default is they all home at the same time,
222 # if this is set it will force each axis to home one at a time in the specified order
223 #homing_order XYZ # x axis followed by y then z last
225 # optional enable limit switches, actions will stop if any enabled limit switch is triggered
226 #alpha_limit_enable false # set to true to enable X min and max limit switches
227 #beta_limit_enable false # set to true to enable Y min and max limit switches
228 #gamma_limit_enable false # set to true to enable Z min and max limit switches
230 alpha_fast_homing_rate_mm_s 50 # feedrates in mm/second
231 beta_fast_homing_rate_mm_s 50 # "
232 gamma_fast_homing_rate_mm_s 4 # "
233 alpha_slow_homing_rate_mm_s 25 # "
234 beta_slow_homing_rate_mm_s 25 # "
235 gamma_slow_homing_rate_mm_s 2 # "
237 alpha_homing_retract_mm 5 # distance in mm
238 beta_homing_retract_mm 5 # "
239 gamma_homing_retract_mm 1 # "
241 #endstop_debounce_count 100 # uncomment if you get noise on your endstops, default is 100
244 zprobe.enable false # set to true to enable a zprobe
245 zprobe.probe_pin 1.28!^ # pin probe is attached to if NC remove the !
246 zprobe.slow_feedrate 5 # mm/sec probe feed rate
247 #zprobe.debounce_count 100 # set if noisy
248 zprobe.fast_feedrate 100 # move feedrate mm/sec
249 zprobe.probe_height 5 # how much above bed to start probe
250 #gamma_min_endstop nc # normally 1.28. Change to nc to prevent conflict,
252 # associated with zprobe the leveling strategy to use
253 #leveling-strategy.three-point-leveling.enable true # a leveling strategy that probes three points to define a plane and keeps the Z parallel to that plane
254 #leveling-strategy.three-point-leveling.point1 100.0,0.0 # the first probe point (x,y) optional may be defined with M557
255 #leveling-strategy.three-point-leveling.point2 200.0,200.0 # the second probe point (x,y)
256 #leveling-strategy.three-point-leveling.point3 0.0,200.0 # the third probe point (x,y)
257 #leveling-strategy.three-point-leveling.home_first true # home the XY axis before probing
258 #leveling-strategy.three-point-leveling.tolerance 0.03 # the probe tolerance in mm, anything less that this will be ignored, default is 0.03mm
259 #leveling-strategy.three-point-leveling.probe_offsets 0,0,0 # the probe offsets from nozzle, must be x,y,z, default is no offset
260 #leveling-strategy.three-point-leveling.save_plane false # set to true to allow the bed plane to be saved with M500 default is false
263 panel.enable false # set to true to enable the panel code
264 panel.lcd smoothiepanel # set type of panel
265 panel.encoder_a_pin 3.25!^ # encoder pin
266 panel.encoder_b_pin 3.26!^ # encoder pin
268 # Example for reprap discount GLCD
269 # on glcd EXP1 is to left and EXP2 is to right, pin 1 is bottom left, pin 2 is top left etc.
270 # +5v is EXP1 pin 10, Gnd is EXP1 pin 9
271 #panel.lcd reprap_discount_glcd #
272 #panel.spi_channel 0 # spi channel to use ; GLCD EXP1 Pins 3,5 (MOSI, SCLK)
273 #panel.spi_cs_pin 0.16 # spi chip select ; GLCD EXP1 Pin 4
274 #panel.encoder_a_pin 3.25!^ # encoder pin ; GLCD EXP2 Pin 3
275 #panel.encoder_b_pin 3.26!^ # encoder pin ; GLCD EXP2 Pin 5
276 #panel.click_button_pin 1.30!^ # click button ; GLCD EXP1 Pin 2
277 #panel.buzz_pin 1.31 # pin for buzzer ; GLCD EXP1 Pin 1
278 #panel.back_button_pin 2.11!^ # back button ; GLCD EXP2 Pin 8
280 # pins used with other panels
281 #panel.up_button_pin 0.1! # up button if used
282 #panel.down_button_pin 0.0! # down button if used
283 #panel.click_button_pin 0.18! # click button if used
285 panel.menu_offset 0 # some panels will need 1 here
287 panel.alpha_jog_feedrate 6000 # x jogging feedrate in mm/min
288 panel.beta_jog_feedrate 6000 # y jogging feedrate in mm/min
289 panel.gamma_jog_feedrate 200 # z jogging feedrate in mm/min
291 panel.hotend_temperature 185 # temp to set hotend when preheat is selected
292 panel.bed_temperature 60 # temp to set bed when preheat is selected
294 # Example of a custom menu entry, which will show up in the Custom entry.
295 # NOTE _ gets converted to space in the menu and commands, | is used to separate multiple commands
296 custom_menu.power_on.enable true #
297 custom_menu.power_on.name Power_on #
298 custom_menu.power_on.command M80 #
300 custom_menu.power_off.enable true #
301 custom_menu.power_off.name Power_off #
302 custom_menu.power_off.command M81 #
304 # Only needed on a smoothieboard
305 currentcontrol_module_enable true #
307 return_error_on_unhandled_gcode false #
310 network.enable false # enable the ethernet network services
311 network.webserver.enable true # enable the webserver
312 network.telnet.enable true # enable the telnet server
313 network.ip_address auto # use dhcp to get ip address
314 # uncomment the 3 below to manually setup ip address
315 #network.ip_address 192.168.3.222 # the IP address
316 #network.ip_mask 255.255.255.0 # the ip mask
317 #network.ip_gateway 192.168.3.1 # the gateway address
318 #network.mac_override xx.xx.xx.xx.xx.xx # override the mac address, only do this if you have a conflict
HCoop / clinton / Smoothieware.git / blob